广 州 视 琨 电 子 科 技 有 限 公 司 Guangzhou Shikun Electronic Technology Company Limited 保密等级:机密 SPECIFICATION 产品规格书 SKO.W603.6 IEEE 802.11b/g/n 2T2R USB Wi-Fi Module Approved by Shikun Checked by 审核 Rechecked by 复审 Approved by 批准 Please send the original back to us after you have approved and signed.
REVISION HISTORY VERSION DATE BOARD ID V0 2020.07.10 SKO.W603.6 A20233 V1 2020.08.26 SKO.W603.6 B20332 PAGE 1\2\3\ 4 DESCRIPTION AUTHOR First Issued. Lee Modify the product pictures, dimensions Lee and package outline. Modify the product V2 2020.09.25 SKO.W603.6 B20332 3\4 pictures and package. \11 Delete software Lee requirements. V3 2020.11.17 SKO.W603.6 B20332 13\14\ Add 15\16 warning information.
Content 1. Introduction(简介) ...................................................... 1 2. FEATURES(特性) ....................................................... 1 3. Block Diagram(结构框图) ............................................... 2 4. Package Outline and Mounting(外形及安装尺寸) ......................... 2 5. Product Pictures(实物图片) .............................................. 3 6. Key Materials(关键物料)................................................. 4 7. General Requirements(一般要求) ................................
SKO.W603.6 1. Introduction(简介) SKO.W603.6 module is based on MEDIATEK MT7603U solution. The MT7603U is a highly integrated Wi-Fi single chip which supports 300 Mbps PHY rate. It fully complies with IEEE 802.11n and IEEE 802.11 b/g standards, offering feature-rich wireless connectivity at high standards, and delivering reliable, cost-effective throughput from an extended distance. This documentation describes the engineering requirements specification. SKO.W603.
SKO.W603.6 4. Package Outline and Mounting(外形及安装尺寸) Note:1. The unit is mm. 2.The tolerance of the external dimensions of the module is ±0.2mm, and the tolerance of the board thickness and unmarked is ±0.2mm. 注意:1. 单位为 mm。 2.模组外形尺寸公差为±0.2mm,板厚及未标注公差为±0.
SKO.W603.6 Pin Definition(引脚定义) PIN SYMBOL DESCRIPTION 1 VDD_5V VDD 5.0V\+5.0V 直流供电输入 2 VDD_5V VDD 5.0V\+5.0V 直流供电输入 3 NC NC\悬空 4 GND Connected to Ground\连接到地 5 GND Connected to Ground\连接到地 6 USB_DM USB2.0 DM Signal\USB2.0 差分负电压信号 7 USB_DP USB2.0 DP Signal\USB2.0 差分正电压信号 8 GND Connected to Ground\连接到地 9 WoW 10 RESET Wake on Wireless LAN\唤醒引脚 (低电平有效,内有 10K 电阻到 3.3V 上拉) RESET\复位引脚 (低电平有效,内部没有上拉电阻,整机端需要加 10K 电阻到 3.3V 上拉) 5.
SKO.W603.6 背视图(bottom view) 6. Key Materials(关键物料) 序号 关键件名称 型号 规格/材料 1 集成电路 MT7603U 48-QFN 2 PCB SKO.W603.6 FR-4,2LAY 3 晶体振荡器 无源晶振,SPXO,± 备注 40MHz 10ppm,12pF,SMD3225 7. General Requirements(一般要求) No. Feature Description 7-1 Operation Voltage 工作电压范围 5.0V+/-0.5 7-2 Current Consumption 最大电流 800mA 7-3 Ripple 纹波 ≤250Vp-p 7-4 Operation Temperature 工作温度范围 0°C to +40°C 7-5 Antenna Type 天线类型 Internal antenna 7-6 USB High Speed USB 2.
SKO.W603.6 8.1 IEEE 802.11b Section Items Contents Specification IEEE802.11b Mode DBPSK, DQPSK and CCK and DSSS Channel CH1 to CH13 TX Characteristics Min. Typ. Max. Unit 14 16 18 dBm 1) fc +/-11MHz to +/-22MHz - - -30 dBr 2) fc > +/-22MHz - - -50 dBr 1) 1Mbps - - -10 dB 2) 2Mbps - - -10 dB 3) 5.5Mbps - - -10 dB 4) 11Mbps - - -10 dB -20 - 20 ppm Min. Typ. Max. Unit 1) 1Mbps (FER ≦8%) - - -83 dBm 2) 2Mbps (FER ≦8%) - - -80 dBm 3) 5.
SKO.W603.6 2) 9Mbps - - -8 dB 3) 12Mbps - - -10 dB 4) 18Mbps - - -13 dB 5) 24Mbps - - -16 dB 6) 36Mbps - - -19 dB 7) 48Mbps - - -22 dB 8) 54Mbps - - -25 dB -20 - 20 ppm Min. Typ. Max.
SKO.W603.6 4. Frequency Error -20 - 20 ppm Min. Typ. Max. Unit 1) MCS0 (PER ≦10%) - - -82 dBm 2) MCS1 (PER ≦10%) - - -79 dBm 3) MCS2 (PER ≦10%) - - -77 dBm 4) MCS3 (PER ≦10%) - - -74 dBm 5) MCS4 (PER ≦10%) - - -70 dBm 6) MCS5 (PER ≦10%) - - -66 dBm 7) MCS6 (PER ≦10%) - - -65 dBm 8) MCS7 (PER ≦10%) - - -64 dBm -20 - - dBm RX Characteristics 5. Minimum Input Level Sensitivity (each chain) 6. Maximum Input Level (PER ≦10%) 8.4 IEEE 802.11n HT40 Section(2.
SKO.W603.6 3) MCS2 (PER ≦10%) - - -74 dBm 4) MCS3 (PER ≦10%) - - -71 dBm 5) MCS4 (PER ≦10%) - - -67 dBm 6) MCS5 (PER ≦10%) - - -63 dBm 7) MCS6 (PER ≦10%) - - -62 dBm 8) MCS7 (PER ≦10%) - - -61 dBm -20 - - dBm 6.
SKO.W603.6 9. Mechanical,Environmental and Reliability Tests (机械、环境和可靠性测试) Test Items Test Conditions Qty Criteria Condition The packed samples was tested at below condition: After test, the outer box and inner box Drop height: 9-1 Drop test 760mm(0.5~9.5kg) 1xBox 610mm(9.5~18.5kg) will not been broken by appearance visual inspection, and the products should be ok. Drop time: 1x corner, 3x edge and 6x face.
SKO.W603.6 Low temperature 9-7 start test Leave samples in -15℃ for 4x hours After test, power on and off the samples 4 to start normally High Temperature and 9-8 Humidity After test, the products appearance, Leave samples in 85℃, 95% RH @ 48 hours 4 Storage Test functional parameter shall be satisfied After test, the products appearance, Low Temperature power, EVM and frequency error with the test specification.
SKO.W603.6 10.
SKO.W603.6 11.
SKO.W603.6 12. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
SKO.W603.6 Installation must be controlled. Installation requires special training CFR 47 FCC Part 15 Subpart C (15.247, DTS ) has been investigated. It is applicable to the modular transmitter This radio transmitter 2AR82-SKOW603601has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated.
SKO.W603.6 l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précédé des mots « Contient un module d'émission », du mot « IC: 24728-SKOW603601 » ou d'une formulation similaire exprimant le même sens, comme suit The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
SKO.W603.6 4. Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual.