Assembly Instructions

ManualsBrandsGuangzhou Shikun Electronics ManualsElectronicsIEEE 802.11b/g/n/a/ac/ax 2T2R USB WiFi Module Integrated BT 2.1+EDR/4.2/5.2

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Caution: The user is cautioned that changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

If power exceeds the limit and the distance（Over 20cm distance in actual use between the device and user） is

compliant with the requirement

FCC RF Radiation Exposure Statement:

The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any

portable device, for example, USB dongle like transmitters is forbidden.

This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This

modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

The device must be professionally installed

The intended use is generally not for the general public.It is generally for industry/commercial use.

The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not

normally required. the user has no access to the connector.

Summary of content (5 pages)

PAGE 1
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 2
Installation must be controlled. Installation requires special training Frequency (MHz) Antenna Type 2400-2500 External Antenna 5100-5900 External Antenna Antenna Gain (dBi) Zhongshan B&T, model: AG-011320-0679 MAX gain: 3.0dBi Shenzhen KTC, model: 3D0504BK07-001 MAX gain：3.5dBi Shenzhen KTC, model: SLK-KG-B3DBS-SMA(P) MAX gain：3.5dBi Shenzhen KTC, model: A100-0062 MAX gain：3.5dBi Shenzhen KTC model: 3D0504BK07-001 MAX gain: 4.5dBi Shenzhen KTC model: SLK-KG-B3DBS-SMA(P) MAX gain：5.
PAGE 3
Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 4
The concrete contents to check are the following three points. 1) Should be installed so that the end user cannot modify the antenna; 2) Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. Le contenu concret à vérifier sont les trois points suivants. 1) doivent être installés de façon que l'utilisateur final ne peut pas modifier l'antenne 2) La ligne d’alimentation doit être conçue en 50ohm Le réglage précis de la perte de rendement, etc.
PAGE 5
Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual.