广 州 视 琨 电 子 科 技 有 限 公 司 Guangzhou Shikun Electronic Technology Company Limited SPECIFICATION 产品规格书 SKI.WB800D.2 IEEE 802.11b/g/n/ax 1T1R USB Wi-Fi Module Integrated Bluetooth 2.1+EDR/3.0/4.x/5.0 Approved by Shikun Checked by 审核 Rechecked by 复审 Approved by 批准 Please send the original back to us after you have approved and signed.
REVISION HISTORY VERSION DATE V0 2021.05.19 V1.0 2021.06.19 V1.1 V1.2 2021.06.19 2021.10.19 BOARD ID SKI.WB800D.2 A21163 SKI.WB800D.2 A21163 SKI.WB800D.2 B21281 SKI.WB800D.2 B21281 PAGE DESCRIPTION AUTHOR All First Issued.
Content 1. Introduction(简介)............................................................................................................1 2. Features(特性)................................................................................................................... 1 3. Package Outline and Mounting(外形及安装尺寸)................................................... 2 4. Pin Definition(引脚定义)................................................................................................. 3 5.
SKI.WB800D.2 1. Introduction(简介) SKI.WB800D.2 is based on AICSEMI AIC8800D, complied with IEEE 802.11b/g/n /ax & BT5.0 standard from 2.4-2.5GHz. The HW architecture for the module is shown in Figure 1. It combines a WLAN MAC, a 1T1R capable WLAN baseband, and RF in CMOS single chip, which are designed to meet both the low power and high throughput application. The AIC8800D provides a complete solution for a high-performance integrated wireless and Bluetooth device.
SKI.WB800D.2 3.
SKI.WB800D.2 4. Pin Definition(引脚定义) 正视图 Top view PIN SYMBOL DESCRIPTION 1 GND Ground\地 2 WiFi(NC) NC,WiFi 默认使用模组 WiFi ipex 3 GND Ground\地 4 GND Ground\地 5 BT(NC) NC,WiFi 默认使用模组 BT ipex 6 GND Ground\地 7 GND Ground\地 8 DP WLAN/BT USB2.0 DP Signal\WLAN/BT USB2.0 差分正电压信号 9 DM WLAN/BT USB2.0 DM Signal\WLAN/BT USB2.0 差分负电压信号 10 3.3V 11 Powerkey 12 BT_Wake_Host QR-ZZPJ-017A 3.3V WiFi is enabled, low level is active, the module has a pull-up 47K Remark: 1.
SKI.WB800D.2 Powerkey timing requirements:The timing requirements of Powerkey and VBAT (power supply 3.3V) are as shown in the figure below. Powerkey lags at least 200us after power-on. In actual use, it is recommended that customers use GPIO to control powerkey. ), the module starts normally! 5.
SKI.WB800D.2 Silkscreen instructions: (1) Inside the red box: B stands for Bluetooth, W stands for WIFI (2) Inside the blue box: B21281 is the product cycle number (3) Inside the yellow box: SKI.WB800D.2 is the product model (4) The content of the product nameplate is as follows 6. Key Materials(关键物料) 序号 关键件名称 型号 规格/材料 1 integrated circuit AIC8800D QFN48 PCB SKI.WB800D.2 FR-4,2LAY 2.3.3.400001535 40MHz 2 3 Crystal oscillation 备注 7. General Requirements(一般要求) No.
SKI.WB800D.2 8. Electrical Characteristics(电气特性) 除非另有说明,电气规范试验都在下列条件下进行: 环境条件温度:25℃±5℃; 电源电压:模块输上入电压 3.3V(±10%); The Test for electrical specification was performed under the following condition unless otherwise specified. Ambient condition Temperature :25℃ ± 5℃; Power supply voltages:3.3V (±10%) input power at the Module; 8.1 IEEE 802.11b Section Items Contents Specification IEEE802.11b Mode CCK Channel CH1 to CH13 Data rate 1, 2, 5.5, 11Mbps TX Characteristics Min. Typ. Max.
SKI.WB800D.2 Mode OFDM Channel CH1 to CH13 Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit 12 14 16 dBm 1) at fc ±11MHz - - -20 dBr 2) at fc ±20MHz - - -28 dBr 3) at fc > ±30MHz - - -40 dBr 1) 6Mbps - - -5 dB 2) 9Mbps - - -8 dB 3) 12Mbps - - -10 dB 4) 18Mbps - - -13 dB 5) 24Mbps - - -16 dB 6) 36Mbps - - -19 dB 7) 48Mbps - - -22 dB 8) 54Mbps - - -25 dB -10 - 10 ppm Min. Typ. Max.
SKI.WB800D.2 14dBm Target (For Each antenna port) 12 14 16 dBm 1) at fc ±11MHz - - -20 dBr 2) at fc ±20MHz - - -28 dBr 3) at fc > ±30MHz - - -45 dBr 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -28 dB -10 - 10 ppm Min. Typ. Max.
SKI.WB800D.2 3) at fc > ±60MHz - - -45 dBr 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -28 dB -25 - 25 ppm Min. Typ. Max.
SKI.WB800D.2 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -27 dB 9) MCS8 - - -30 dB 10) MCS9 - - -32 dB 11) MCS10 -34 dB 12) MCS11 -35 dB 4. Frequency Error RX Characteristics -20 - 20 ppm Min. Typ. Max. Unit 5.
SKI.WB800D.2 2)Delta f2max(For at least 99.9% of all Delta f2max) - 121 - kHz - 0.85 - kHz - ±20 - kHz 1) One Slot packet drift (DH1) - ±15 - kHz 2) Three Slot packet drift (DH3) - ±15 - kHz 3) Five Slot packet drift (DH5) - ±15 - kHz 4) Max Drift Rate - ±15 - kHz/50us 1. Receiver Sensitivity (BER<0.1%) - -92 - dBm 2. Maximum usable signal (BER<0.1%) - -5 - dBm 3)Delta f2/ Delta f1 3.Initial Carrier Frequency Tolerance 4.
SKI.WB800D.2 1) π/4-DQPSK - -91 - dBm 2) 8PSK - -85 - dBm 1) π/4-DQPSK - -5 - dBm 2) 8PSK - -5 - dBm 2. Maximum usable signal (BER<0.1%) 8.6.3 LE Specification Items Contents Host Interface USB Antenna Reference Small antennas with 0~2 dBi peak gain Channel CH0 to CH39 Min. Typ. Max. Unit - 6 - dBm 225 - 275 kHz 185 - - kHz 0.8 0.
SKI.WB800D.2 Drop time: 1 each Face and edge. X-Y-Z direction, first Frequency changing from 10Hz to 30Hz to 10Hz,amplitude 0.75mm, 10-2 Vibration test After test, the Appearance, Power EVM 5 times vibrations, then 3 frequency Changing from and Frequency error shall be satisfied with the specification. 30Hz to 55 Hz to 30 Hz, amplitude 0.15mm, 5 time vibration.
SKI.WB800D.2 Low 10-8 temperatur e storage Leave samples in standard test condition Leave the samples in 3 -25±3℃@24 hours test Low 10-9 temperatur e load test for 2 hours then test, the Appearance, Power, EVM and Frequency error shall be satisfied with the test specification.
SKI.WB800D.2 10.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “ Contains IC: 24728-SKIWB800D21” any similar wording that expresses the same meaning may be used.
Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual.
Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.
2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements. a) Information that includes permitted variances (e.g.
2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an “omni-directional antenna” is not considered to be a specific “antenna type”)).
2.10 Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.