广 州 视 琨 电 子 科 技 有 限 公 司 Guangzhou Shikun Electronic Technology Company Limited 保密等级:机密 SPECIFICATION 产品规格书 SKI.WB663U.1 IEEE 802.11a/b/g/n/ac 2T2R USB Wi-Fi Module Integrated Bluetooth 2.1+EDR/4.2/5.1 Approved by Shikun Checked by 审核 Rechecked by 复审 Approved by 批准 Please send the original back to us after you have approved and signed.
REVISION HISTORY VERSION DATE V0 2021.05.31 BOARD ID SKI.WB663U.1 A21173 PAGE DESCRIPTION AUTHOR All First Issued.
Content 1. Introduction(简介).............................................................................................................. 1 2. FEATURES(特性).................................................................................................................. 1 3. Block Diagram(结构框图)..................................................................................................2 4. Package Outline and Mounting(外形及安装尺寸)..................................................... 2 5.
SKI.WB663U.1 1. Introduction(简介) SKI.WB663U.1 module is based on MEDIATEK MT7663BUN solution. MT7663B is a highly integrated single chip which features a low power 2x2 11a/b/g/n/ac dual-band Wi-Fi subsystem and a Bluetooth subsystem. The Wi-Fi subsystem contains the 802.11a/b/g/n/ac radio, baseband, and MAC that are designed to meet both the low power and high throughput application. The Bluetooth subsystem contains the Bluetooth radio which complies with Bluetooth v2.1+EDR, v4.2, and v5.
SKI.WB663U.1 3. Block Diagram(结构框图) 4. Package Outline and Mounting(外形及安装尺寸) 模组结构图及建议 PCB 封装如下(焊盘圆弧直径与焊盘宽度一致): 23 21 20 18 17 24 32 9 1 8 模组俯视图 模组侧视图 模组底视图 NOTE: 1.板内顶层器件最高2.1mm; 2.模组外形尺寸公差为±0.15mm,板厚以及未标注公差为±0.
SKI.WB663U.1 5. Pin Definition(引脚定义) WLAN_EN 需要在主板上用 10K 电阻上拉到 3.3V。 正视图 PIN SYMBOL DESCRIPTION 1 NC NC\不使用 2 NC NC\不使用 3 NC NC\不使用 4 NC NC\不使用 5 GND Ground\地 6 WL_USB_DP WLAN/BT USB2.0 DP Signal\WLAN/BT USB2.0 差分正电压信号 7 WL_USB_DM WLAN/BT USB2.0 DM Signal\WLAN/BT USB2.0 差分负电压信号 8 GND Ground\地 9 BT_USB_DP NC\不使用,BT 与 WIFI 复用 USB 10 BT_USB_DM NC\不使用,BT 与 WIFI 复用 USB 11 GND Ground\地 12 BT_RF BT RF Output, connect to external antenna\蓝牙射频输出,连接外置天线 13 GND Ground\地 BT_W
SKI.WB663U.1 发模组复位 29 GND Ground\地 30 VDD_3.3V 3.3V input\3.3V 输入 31 32 3D_SYNC (GPIO0) Frame sync signals from TV to sync with 3D glass via Bluetooth\3D 帧同步信号 Ground\地 GND 6.
SKI.WB663U.1 7. Key Materials(关键物料) 序号 关键件名称 型号 规格/材料 1 集成电路 MT7663BUN FN-76 2 PCB SKI.WB663U.1 FR-4 , 4LAY P178 3 晶体振荡器 40MHz JWT 4 双工器 CN4040M00012T211523 0 RFDIP160806ALM6T30 备注 Walsin 8. General Requirements(一般要求) No. Feature Description 8-1 Operation Voltage 工作电压范围 3.3V+/-0.3 8-2 Current Consumption 最大电流 700mA 8-3 Ripple 纹波 ≤100mV 8-4 Operation Temperature 工作温度范围 0°C to +40°C 8-5 Antenna Type 天线类型 External antenna 8-6 USB High Speed USB 2.
SKI.WB663U.1 10. Mechanical,Environmental and Reliability Tests (机械、环境和可靠性测试) Test Items Test Conditions Qty Criteria Condition The packed samples within 100Kg can be tested Drop height: 10-1 Drop test Face Side: 800/600/450mm Edge line: 600/450/350mm 1xB ox After drop test, the outer box and inner box will not been broken by appearance visual inspection. Drop time: 1 each Face and edge.
SKI.WB663U.1 frequency Changing from 30Hz to 55 Hz to 30 Hz, amplitude 0.15mm, 5 time vibration. Impact After test, the Appearance, Power EVM acceleration: 10-3 Impact test 3 50m/sec2; and Frequency error shall be satisfied with the specification. Impact duration: 16ms; Impact times: 1000. 1.
SKI.WB663U.1 satisfied with the test specification. After test, leave the samples in standard One cycle duration 10-10 Temperature -10±3℃@3H circle test 40±3℃ @3H condition and tested Power EVM and 3 the characters shall be satisfied with the Total cycle: 10x 10-11 Continuous TP test Frequency error shall be qualified and all test specification. During test, There will not been appeared Twice cycle duration -10±3℃@4H +60±3℃@4H, 3 signal disconnection or interruption between DUT and AP.
SKI.WB663U.
SKI.WB663U.1 (4)标签样式: 内盒标签示例【具体内容根据系统打印为准】 12. Software Requirements(软件要求) The driver supports the following operating systems: Microsoft Windows XP, Vista and Win7. 驱动程序支持以下操作系统:微软 Windows XP,Vista 和 win7。 13.
SKI.WB663U.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “ Contains IC: 24728-SKIWB663U11” any similar wording that expresses the same meaning may be used.
WF2 Antenna MAX:1.5dBi Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. La bande 5 150-5 250 MHz est réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. Users are advised that high-power radars are allocated as primary users (i.e.
The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. This module is a limit modules. host manufacturer should confirm with module manufacturer for the installation method in end system. The external circuit should be installed in the host and connect to BT_RFIO.