User's Manual

ManualsBrandsGuangzhou MCOHome Technology ManualsElectronicsMH-S220

User Manual

Micro Switch

MH-S220

Introduction

Micro Switch is a Z-Wave enabled module that can be set in existing in-wall switches. It

supports basic command class, and also can act as a repeater in Z-Wave network. This product

can be included and operated in any Z-Wave network with other Z-Wave certified devices from

any other manufacturers.

Specifications

Power supply: 85~260VAC, 50/60Hz

Z-Wave frequency: 868.42MHz (EU), 908.42MHz (US) or other frequency customized

*Max output: 1*10A （Resistive）

Dimension：44 *38 *17mm (L *W *H)

*Note: For non-resistive load, a derating output is highly suggested.

Installation Instructions

IMPORTANT:

 A qualified electrician with the understanding of wiring diagrams and knowledge of

electrical safety should complete the installation inside the main circuit box (normally

outside your house)

 Read all instructions and documentation and save for future reference

Step1 Preparing

CAUTION: Cut off power supply at circuit breaker or fuse before installation to avoid fire, shock or

death!

1. Remove the wall switch cover plate.

2. Disconnect both wires from the wall switch.

Step2 Wiring ( standard strip length: 6-7mm)

1. Connect Hot Line to “L”.

2. Connect Neutral Line to “N”.

3. Connect “I” with “L”.

4. Connect “O” with load and then with “N”.

5. Connect “S1”, “S2” with external switch separately,

and then with “L” .

Summary of content (5 pages)

PAGE 1
User Manual Micro Switch MH-S220 Introduction Micro Switch is a Z-Wave enabled module that can be set in existing in-wall switches. It supports basic command class, and also can act as a repeater in Z-Wave network. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from any other manufacturers. Specifications Power supply: 85~260VAC, 50/60Hz Z-Wave frequency: 868.42MHz (EU), 908.
PAGE 2
User Manual Step3 Mounting In-Wall Box Mount wall switch and cover plate back to the in-wall box. Step4 Restoring Power Restore power at circuit breaker or fuse. Installation is complete. Operation INCLUDING device into Z-Wave network: 1. Set controller into INCLUSION mode. Follow the instructions provided by the controller/gateway manufacturer. 1. Press the momentary button on the device, or the connected external button S1 3 times in quick succession.
PAGE 3
User Manual Multi Channel Association: To set association groups by “COMMAND_CLASS_MULTI_CHANNEL_ ASSOCIATION”. Refer to “Z-Wave Command Class Specification” for detail information, or consult the information provided by controller/gateway manufacturer. The device supports 3 association groups(AG): 1st AG: reports device’s state. It supports only one Node ID (with/without End Point). A controller/gateway SHOULD be associated to this AG. 2nd AG: to control the associated devices synchronously.
PAGE 4
User Manual 0x00 report ON/OFF state of S1 to AG2 Operation report 8 from Switch1 to 1 Association Group2 0x01 only report ON state of S1 to AG2 0x02 only report OFF state of S1 to AG2 0x00 0xFF no report to AG 2 0x01 enable Scene Activation & send Basic ON/OFF to associated devices 9 Switch 2 function 1 0x02 Scene Activation only 0x01 0x03 send Basic ON/OFF only 0xFF disable S2 Function 0x00 send Basic ON or Basic OFF to AG3 Operation report 10 from Switch2 to when turn on/off S2 1 Associat
PAGE 5
User Manual SAFETY NOTICE 1. Flush-mount only into a UL/ETL/CE certified plastic junction box and switch panel cover. The minimum size should be 65*65*42mm, minimum Volume is 180cm3. 2. Use Copper Conductors Only. 3. CAUTION - Risk of Electric Shock - More than one disconnect switch may be required to de-energize the equipment before servicing. 4. WARNING-This device shall not be used in combination with a wall switch controlling a receptacle.