Users Manual

ManualsBrandsGuangzhou Goldsun Electronic ManualsElectronicsslacker digital suspension tuner

Table Of Contents

.. 一·

SMSUNG

Motool Service Assistant 4.0

















口



赁印或霆



IGI









，

User Guida

�

 彝L —-

U.S. Patent No. 9,021,872

Summary of content (9 pages)

PAGE 1
.. 一· SIIMSUNG Motool Service Assistant 4.0 The new Service Assistant app works as a virtual remote display for the new Slacker V4 and allows you to keep notes and settings on all your off-road, street and adventure motorcycles and full suspension mountain bikes to! Keep all your bikes and setting safe and secure in the cloud and accessible from any iOS or Android device with internet connectivity. Take your ride to the next level with this simple, free app by Motool! ， —- � 口 ...
PAGE 2
Slacker V4 Overview (D For virtual remote just turn Slacker on and open the app. You do not need to pair your phone, just the wireless remote. *Android requires location services to be enabled. 盓缢气 G) Power/Reset -Press for 1 second to turn on. -Press for 5 seconds to turn off. -Press once to reset Sacker to zero. -Automatically turns off after 5 min. LCD Display -Displays readings in millimeters. -Displays system messages. -Backlit for poor lighting cond巾ons. -Low battery indicator.
PAGE 3
。。 Quick Tips • Be sure to install 2) A从batteries before use. ·For dirt bikes, always take measurements across the arc of the axle except for 2016 and newer KTM and Husky bikes. Measure to the provided mark on the fender for those bikes. • For street and adventure bikes, always measure vertically from the axle. ·For mountain bikes, be sure to take the initial travel measurement. ·Always center Slacker on the axle and angle with the cable.
PAGE 4
。。 Dirt Bikes 0 1) Place the universal clip or drill a small hole where the arc of the axle meets the side plate/fender. 2) Make sure you place the butt of the clip all the way against the plastics to prevent movement. 1)To find the a『c of the axle, simply take a piece of string and pinch one end against the swing arm pivot axle. Then grab it at the rear axle with your other hand and swing it up to see whe『e it hits the plastics.
PAGE 5
KTM & Husqvarna newer) (2016 and 0 。 1) Place the universal clip or drill a small hole at the sag mark provided by the factory. 2) Make sure you place the butt of the clip all the way against the plastics to prevent movement. 1) Place Slacker centered on the rear axle, extend the 『etractable slacker cable and hook to the clip or the hole in the plastics from the previous step. 2) Angle Slacker so the cable exits at a 90" angle. 3) Turn Slacke『 on by pressing the power button for 1 second.
PAGE 6
C) Street Bikes 1) Place a clear adhesive loop directly above the rear axle with the loop oriented vertically. Note: Make sure to clean the area of dirt and oils before you place the loop to assure the adhesive loop sticks properly and does not get pulled off the bodywork. ＠ 1) Place Slacker centered on the rear axle, extend the retractable slacker cable and hook it to the loop. ° 2) Angle Slacker so the cable exits at a 90 angle. 3) Turn Slacker on by pressing the power button for 1 second.
PAGE 7
C) Adventure Bikes 1) Place a clear adhesive loop directly above the rear axle with the loop oriented vertically. If you have panniers, you can also place the loop on the back side of them in most cases. Note: Make sure to clean the area of dirt and oils before you place the loop to assu「e the adhesive loop sticks properly and does not get pulled off the bodywork. ＠ 1) Place Slacker centered on the rear axle, extend the retractable slacker cable and hook it to the loop.
PAGE 8
Mountain Bikes 0 1) Strap the universal fork/seat post adapter to the seat post and angle it out slightly to keep the retractable cable clear of the rear tire. 2) Make sure you snug the cinch strap付mly to the seat post to prevent any movement. ＠ 1) Place the MTB hex key axle inse『t on the magnet and insert into hex key in the axle. 2) Pull the retractable cable out and hook it on the universal fork/seat post adapter. ° 3) Angle Slacker so the cable exits at a 90 angle.
PAGE 9
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.