User's Manual

ManualsBrandsGuangzhou FiiO Electronic Technology ManualsElectronics2.4GHz Wireless Audio Transmitter

FiiO

W1T1 User Manual

Read this instruction carefully before using the product

Introduction to FiiO W1T1——Wireless Audio Transmitter

Brief introduction

W1T1 is an all-in-one machine which with multifunction of audio decoder and 2.4G

wireless transmitter. It can decode digital audio for inputs of optical, coaxial and

USB, outputs via optical port (Digital signal) and RCA port (Analog signal), while

transmits through 2.4G so as to receive by the receiver in agreement. In the same

way, it can input analog signal via RCA port and transmits by 2.4G as well.

Specifications

●Analog output range: 1.3Vrms（0dB Fs）

●Analog output THD: 0.006%（-3dB ）

●Frequency response: 20Hz-20 KHz

●Signal To Noise Ratio:

●RF Frequency: 2404-2479MHz

●RF Power：＜10dBm

●Sample rate: 24Bit 192 KHz Max.（Optical/Coaxial）

16Bit 44.1/48 KHz Max.（USB）

●Power Voltage： DC-5.0V

●Size: 141mmx82.7mmx23.2mm

●Weight: 175g

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio frequency energyand, if not

Summary of content (6 pages)

PAGE 1
FiiO W1T1 User Manual Read this instruction carefully before using the product Introduction to FiiO W1T1——Wireless Audio Transmitter Brief introduction W1T1 is an all-in-one machine which with multifunction of audio decoder and 2.4G wireless transmitter. It can decode digital audio for inputs of optical, coaxial and USB, outputs via optical port (Digital signal) and RCA port (Analog signal), while transmits through 2.4G so as to receive by the receiver in agreement.
PAGE 2
installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following  --Reorient or relocate the receiving antenna.
PAGE 3
-In order, they are Optical, Coaxial, Analog and USB. ●Optical Input—Wireless transmission, optical output and RCA analog output. ●Coaxial Input—Wireless transmission, optical output and RCA analog output. ●RCA Analog Input—Wireless transmission. ●USB Audio Input--- Wireless transmission, optical output and RCA analog output. ⑧ * Working Status Indicator - Connection: Blue light remains on steadily. - Connectionless: Blue light flashes once per three-second.
PAGE 4
To guarantee the transmitting quality, the height of the wall-hung is supposed to be higher than 1.2m. And make sure the transmission side is facing outside without any obstacles surrounded by. A: With one wall-hung holder: 1. Stick sponge mat to the holder (see following picture). 2. Fix the holder to the wall by two ST 3.5 nails (self-prepare). 3. Put W1T1 on. B: With two wall-hung holders: 1. Stick sponge mats to the two holders. 2. Fix the holders to the wall by two ST 3.5 nails (self-prepare). 3.
PAGE 5
●Intermittent connection: Obstacles may gather around the devices or between them, please remove the potential blocks or shorten the distance (it is highly suggested to put the two devices within seeable distances). ●Unable to use the USB sound card function: Auto install the driver according to the computer’s prompt and set the output device as…….. (See following picture). Special Statement: ★ FiiO has the final interpretation of these instructions.
PAGE 6