Installation Instructions

ManualsBrandsGuangzhou Elite Education & Technology ManualsElectronicsWIFI&BLE-MODULE

Table Of Contents

2.2 List of applicable FCC rules
a) Information that includes permitted variances (e.g., trace boundary limits, thickness, length, width, shape(s), dielectric constant, and impedance as applicable for each type of antenna); b) Each design shall be considered a different type (e.g., a...

LY-C3-22P WIFI&BLE-MODULE

This is a support WIFI b/g/n and BLE5 RF module，The module make the host application

development easier as as a bridge of smart phone peripherals. User's’existing products or

solutions with this module, can communicate with mobile devices (with Bluetooth 5.0 and WIFI

b/g/n) , realize intelligent control and management under the bridge (serial port) mode. Users

can design their own solutions or products to use the module to extend simple peripherals

under the direct driving mode,to release new peripherals in lowest cost and efficiency.

It works in the 2.4 GHz ISM band，BLE to work at 2402 MHZ to 2480 MHZ and wifi working

at 2412 MHZ to 2472 MHZ band，The maximum output power control of the radio frequency in

17 bgn wifi b mode

Features:

1.Convenient, do without any Bluetooth protocol stack application experience.

2.Using universal serial to design users’ interface with bi-directional reading and

simple operation

3.Dimensional channel design, minimize data packet processing, and maximize

the communication efficiency .

4.Ultra low power consumption in standby mode.

Applications:

 2.4-GHz Bluetooth low energy Systems

 Mobile Phone Accessories

 Sports and Leisure Equipment

 Health Care and Medical

 Home and Building Automation

 Consumer Electronics

Summary of content (8 pages)

PAGE 1
LY-C3-22P WIFI&BLE-MODULE This is a support WIFI b/g/n and BLE5 RF module，The module make the host application development easier as as a bridge of smart phone peripherals. User's’existing products or solutions with this module, can communicate with mobile devices (with Bluetooth 5.0 and WIFI b/g/n) , realize intelligent control and management under the bridge (serial port) mode.
PAGE 2
FCC WARNING FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 3
antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
PAGE 4
Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See alsoSection 2.
PAGE 5
module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This Single Modular procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state how control of the product into which the modular transmitter will be installed will be maintained such that full compliance of the product is always ensured.
PAGE 6
Explanation: The module complies with FCC radiofrequency radiation exposure limits for uncontrolled environments. The device is installed and operated with a distance of more than 20 cm between the radiator and your body." This module follows FCC statement design, FCC ID : 2A8RE-C322P 2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions.
PAGE 7
The module manufacturers shall provide a list of acceptable unique connectors. Explanation: The product antenna uses an irreplaceable antenna with a gain of 0dBi 2.8 Label and compliance information Grantees are responsible for the continued compliance of their modules to the FCC rules. This includes advising host product manufacturers that they need to provide a physical or e-label stating “Contains FCC ID” with their finished product.
PAGE 8
as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Explanation: The module without unintentional-radiator digital circuity, so the module does not require an evaluation by FCC Part 15 Subpart B. The host shoule be evaluated by the FCC Subpart B.