TPAD10M RFID Pad Reader User Manual ◆ Before you use this product, please carefully read this manual, and properly keep it for future reference. ◆ As our products continue improving, they may be changed without advanced notice. ◆ The contents of this manual have been carefully checked. For any printing error or misunderstanding content, please contact us as soon as possible. Version: V1.
User Manual Contents 1. 2. 3. 4. 5. 6. Product Overview ................................................................................ 1 1.1. Product Introduction .................................................................... 1 1.2. Product Features .......................................................................... 1 1.3. Pictures ........................................................................................ 1 1.4. Main Parameter................................................
User manual 1. Product Overview 1.1. Product Introduction TPAD10M is a RFID reader-writer machine that is specially designed for self-checkout and check-in, book sorter and production lines. It has the super anti-interference ability of reading and writing. The product uses a metal shielding design, so they can be installed in metal environment and not affected by the metal at the bottom and around.
User manual 1.4. Main Parameter Table 1 Description of main technical parameters of the product Parameters Description Operating Frequency 13.56MHz Support Standard ISO15693, ISO14443A, ISO18000-3M1 ISO18000-3M3 RF Power 0.2W Communication Interface USB Recognition Distance ISO 14443A: 15cm ISO 15693: 24cm Range Of Reading Within Agreed Area ≤1cm Voltage 5VDC（USB powered） Maximum Power Consumption 1W Metal Shielding Design Yes Shell Material PCB and metal plate Dimensions 379.
User manual 2. Product Structure 2.1. Product Appearance Figure 1 Product appearance description Table 2 Product appearance description No. Description ① Power switch ② USB interface ③ LED indicator ④ Sensing area Guangzhou Andea Electronics Technology Co., Ltd. http://www.gzandea.
User manual 2.2. Product Dimensions Figure 2 Product dimension 2.3. Hardware Interface Description 2.4. Communication Interface Communication interface of the device adopts USB interface, and it can connect directly through the computer USB interface. as shown below: Figure 3 USB communication interface 2.5. Power Switch This device is equipped with a power switch button , as shown below: Guangzhou Andea Electronics Technology Co., Ltd. http://www.gzandea.
User manual Figure 4 Power switch 3. Device Connection The device is connected to the PC via a USB communication interface, and power is supplied via USB without additional power supply: Figure 5 Connect via the device's own USB cable 4. Description Of Indicator Light Figure 6 Indicator light Guangzhou Andea Electronics Technology Co., Ltd. http://www.gzandea.
User manual Table 3 Description of indicator light Status Function Description LED 1 The device is powered on normally when the red light flashes. LED 2 The device detects an RFID tag or card when the blue light is on 5. Instructions Of Configuration Tools Please refer to Section 3 "Device Connection" to connect the device. After the device is connected, press the power button.
User manual Since the communication interface of the device is a USB interface, select "USB Communication" in [Communication Interface] under [Search Parameters]. click the [Search] button to find the device. When the device is found, the device information will be automatically displayed in the "Discovered Devices" list as follows: ③ ① ② ④ Figure 8 Connection steps As shown above (Step ④), click the "Start" button to enter the main interface of the test software. 5.1.
User manual Figure 9 Parameter configuration interface 5.1.1. Communication Interface Figure 10 Configuration interface for communication interface ⚫ Bus address: between 1-255 ⚫ Baud Rate: 9600, 19200, 38400, 57600, 115200, 230400 ⚫ Parity check type: None, Odd, Even Guangzhou Andea Electronics Technology Co., Ltd. http://www.gzandea.
User manual 5.1.2. Buzzer Default Parameters Figure 11 Configuration interface for buzzer default parameters ⚫ Type: Unchanged, On, Off, Flash. ⚫ Frequency: value range from 0 to 255, only applicable for the Flash type. ⚫ Active time: the frequency of buzzer, only applicable for the Flash type. 5.1.3.
User manual 2)Timing for Auto Close RF：Value range: 0-256, the RF enters the idle mode if no operation in a specified time. ⚫ Air protocol selection 1) ISO15693: Enable to count tags of ISO15693 air protocol. 2) ISO14443A: Enable to count tags of ISO14443A air protocol. 3) ISO18000p3m3: Enable to count tags of ISO18000p3m3 air protocol. 4) ISO14443B: Enable to count tags of ISO14443B air protocol. ⚫ ISO15693 1) Data coding: 1/4, 1/256. 2) Subcarrier: single negative carrier, double negative carrier.
User manual ⚫ Basic options 1) Disable anti-collision: whether to turn off anti-collision function. 2) Beep when discovery tags: set whether the buzzer buzzes when the tag is detected. 3) Only read new tags: each tag is only read once, when it does not leave the antenna sensing area. 4) Stop Trigger Try N times when no tags: set the number of attempts if no new tags are found. Max Timeout: set the time of stopping trigger due to timeout. ⚫ ISO15693 1) AFI: 00-FF.Note: 00 means not to enable.
User manual 5.1.5. System Work Mode Figure 14 Configuration interface for system work mode ⚫ Mode: 1) Host mode: the host software needs to send commands. 2) Scan mode: the inventory can be automatically completed, even if the host software does not send commands; scan setting in the scan mode should be configured in advance. ⚫ Scan Mode Configuration: 1) Filtered time of duplicated tag(sec): The tag can only be counted again after leaving for the specified time.
User manual ④ Output format of UID: A. Format as hex string. B. Format as LSB 3 bytes convert to integer string. C. Format as LSB 4 bytes convert to integer string. D. Format as compliant with Wiegand. E. Format as compliant with Wiegand fix 8 bytes. ⑤ UID length: 0-8, 0 for unlimited length, output of a complete UID. 4) Parameter of reading block with ISO15693 Byte offset: The offset of the first byte to be read. Byte count: The number of bytes to be read.
User manual Note: Step 1: Select the menu "ISO Multi-Tag Test" in the main interface of the software; Step 2: Select the "Inventory " in the drop-down list above the "Start" button; Step 3: Click the "Start" button to carry out the inventory testing. 5.2.2.
User manual After the above steps, you can read and write tags, as shown below: Figure 17 Single tag reading and writing steps Steps: 1) Set the data block of the tag to be operated in the Addr drop-down box and the Num drop-down box.
User manual Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s).
Guangzhou Andea Electronics Technology Co., Ltd. Address: Room 401, Building H, Jingye San Street, Yushu Industrial Park, Economic And Technological Development Zone, Guangzhou. Zip code: 510663 Phone: 0086-20-32039550, 32039551, 32039552 Fax: 0086-20-32039553 Website: http://www.gzandea.
