RL863 Micro-power Multi-protocol Reader User Manual ◆ Before you use this product, please read this manual carefully, and properly keep it for future reference. ◆ As our products continue improving, they may be changed without advanced notice. ◆ The copyright of this manual belongs to our company. Unauthorized plagiarism or dissemination will be held legally responsible.
Version:V1.
User manual Contents 1. Product Overview ........................................................................... 1 1.1. Introduction ......................................................................... 1 1.2. Product Features .................................................................. 1 1.3. Pictures ............................................................................... 1 1.4. Main Parameter ................................................................... 2 2.
User manual 1. Product Overview 1.1. Introduction This product complies with ISO 15693, ISO 18000-3M3 and ISO 14443A protocol standards, it has high sensitivity reading and writing performance and fast anti-collision processing algorithm which supports reading electronic tags of each protocol at the same time. This product is widely used in desktop card issuance, access control systems, electronic bills, libraries, finance and other fields. 1.2. Product Features ➢ Operating frequency: 13.
User manual 1.4. Main Parameter Table 1 Description of main technical parameters of the product Parameter Description Operating Frequency 13.56MHz Support Standard ISO 15693、ISO 18000-3M3 and ISO 14443A Recognition Distance ISO 15693 16 cm ISO14443A 10 cm ISO 18000-3M3 6 cm Communication Interface USB Voltage 5V(USB powered) Maximum Power 0.
User manual Mini USB Interface Figure 1 Communication interface 3. Product Dimension The external dimensions of the product are shown in the following figure (unit: mm): Figure 2 Product dimension 4. Device Connection Before using the reader, connect the reader to the computer with the supplied "USB cable", as shown in the following figure: Guangzhou Andea Electronics Technology Co., Ltd. http://www.gzandea.
User manual USB Figure 3 Connection diagram 5. Instructions Of Configuration Tools After the device is connected and powered on normally, open the R-Tool folder of the configuration tool and find the file in the folder directory. Double-click this file to open the configuration tool, as shown below: Figure 4 R-Tool connection interface Select the corresponding communication method according to the actual interface type used by the device.
User manual ③ ① ② ④ Figure 5 Connection steps As shown above (Step ④), click the "Start" button to enter the main interface of the test software. 5.1. Configuration Description Of Parameters 5.1.1. Communication Interface Figure 6 Configuration interface for communication interface ⚫ Bus address: between 1-255 ⚫ Baud Rate: 9600, 19200, 38400, 57600, 115200, 230400 ⚫ Parity check type: None, Odd, Even Guangzhou Andea Electronics Technology Co., Ltd. http://www.gzandea.
User manual 5.1.2. Buzzer Default Parameters Figure 7 Configuration interface for buzzer default parameters ⚫ Type: Unchanged, On, Off, Flash. ⚫ Frequency: value range from 0 to 255, only applicable for the Flash type. ⚫ Active time: the frequency of buzzer, only applicable for the Flash type. 5.1.3.
User manual 2)Timing for Auto Close RF:Value range: 0-256, the RF enters the idle mode if no operation in a specified time. ⚫ Air protocol selection 1) ISO15693: Enable to count tags of ISO15693 air protocol. 2) ISO14443A: Enable to count tags of ISO14443A air protocol. 3) ISO18000p3m3: Enable to count tags of ISO18000p3m3 air protocol. 4) ISO14443B: Enable to count tags of ISO14443B air protocol. ⚫ ISO15693 1) Data coding: 1/4, 1/256. 2) Subcarrier: single negative carrier, double negative carrier.
User manual ⚫ Basic options 1) Disable anti-collision: whether to turn off anti-collision function. 2) Beep when discovery tags: set whether the buzzer buzzes when the tag is detected. 3) Only read new tags: each tag is only read once, when it does not leave the antenna sensing area. 4) Stop Trigger Try N times when no tags: set the number of attempts if no new tags are found. Max Timeout: set the time of stopping trigger due to timeout. ⚫ ISO15693 1) AFI: 00-FF.Note: 00 means not to enable.
User manual 5.1.5. System Work Mode Figure 10 Configuration interface for system work mode ⚫ Mode: 1) Host mode: the host software needs to send commands. 2) Scan mode: the inventory can be automatically completed, even if the host software does not send commands; scan setting in the scan mode should be configured in advance. ⚫ Scan Mode Configuration: 1) Filtered time of duplicated tag(sec): The tag can only be counted again after leaving the specified time.
User manual ④ Output format of UID: A. Format as hex string. B. Format as LSB 3 bytes convert to integer string. C. Format as LSB 4 bytes convert to integer string. D. Format as compliant with Wiegand. E. Format as compliant with Wiegand fix 8 bytes. ⑤ UID length: 0-8, 0 for unlimited length, output of a complete UID. 4) Parameter of reading block with ISO15693 Byte offset: The offset of the first byte to be read. Byte count: The number of bytes to be read.
User manual Note: Step 1: Select the menu "ISO Multi-Tag Test" in the main interface of the software; Step 2: Select the "Inventory " in the drop-down list above the "Start" button; Step 3: Click the "Start" button to carry out the inventory testing. 5.2.2.
User manual After the above steps, you can read and write tags, as shown below: Figure 13 Single tag reading and writing steps Steps: 1) Set the data block of the tag to be operated in the Addr drop-down box and the Num drop-down box.
User manual 2) The reader can read normally, but the light is still off, it may be the reader indicator is broken. 2.The reader works but the tag cannot be read normally: Failure analysis: 1)The tag is damaged; 2)The performance of the antenna board is unstable or the device has poor contact. Troubleshooting method: Please check whether the tag is damaged, and take another tag to test.
User manual Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s).
Guangzhou Andea Electronics Technology Co., Ltd. Address: Room 401, Building H, Jingye San Street, Yushu Industrial Park, Economic And Technological Development Zone, Guangzhou. Zip code: 510663 Phone: 86-020-32039550, 32039551, 32039552 Fax: 86-020-32039553 Website: http://www.gzandea.