PBYTJ Series HF RFID Embedded Reader User Manual ◆ Before you use this product, please carefully read this manual and properly keep it for future reference. ◆ As our products continue improving, they may be changed without advanced notice. ◆ The contents of this manual have been carefully checked. For any printing error or misunderstanding content, please contact us as soon as possible. Version: V1.
User manual Contents 1. Product Overview ................................................................................... 1 1.1. Product Introduction ....................................................................... 1 1.2. Product Features ............................................................................. 1 1.3. Product Models .............................................................................. 1 1.4. Product Parameters .........................................................
User manual 1. Product Overview 1.1. Product Introduction This product is a super anti-interference ability reading and writing device designed for self-service kiosk, book sorting machine, production line and other fields. The whole series adopts metal shielding design which will not be affected by the bottom and surrounding metal environment. 1.2. Product Features ➢ RF Power: 0.25~1.
User manual PBYTJ160 1.4. Product Parameters Table 1 Description of main technical parameters of the product Parameters / Models PBYTJ311 PBYTJ160 Working Frequency 13.56MHZ Support Protocols ISO/IEC 15693 and ISO/IEC 18000-3M1 RF Power 0.25~1.5W (adjustable) Recognition Distance 36 cm 16cm Communication Interface RS232 Working Modes Host or Scan Mode (Set by configuration tool) Working Power 12V DC Max Power Consumption 3.5W 3.
User manual 2. Product Structure 2.1. Product Appearance ① ④ ② ③ Figure 1 Product appearance description Table 2 Product appearance description No. Description ① Detection Area ② RS232 communication and power interface ③ Indicator Light ④ Metal shielding Cover Guangzhou Andea Electronics Technology Co., Ltd. http://www.gzandea.
User manual 2.2. Product Dimensions Figure 2 PBYTJ311 Figure 3 PBYTJ160 Chassis opening requirements of installing the detection area: When the equipment is installed in a metal chassis, the panel above the detection area must not be a metal material panel; if a metal panel is used, it must be opened and then a non-metal panel should be added. The size of the opening should not be less than Guangzhou Andea Electronics Technology Co., Ltd. http://www.gzandea.
User manual the size of the iron cover at the bottom of the equipment. which is: PBYTJ311 detection surface opening must be ≥ 320* 220MM. PBYTJ160 detection surface opening must be ≥ 140* 67MM. 3. Interface Description The communication interface (RS232) and power interface (DC 12V/1A) of this product use 3.
User manual Figure 6 DB9 connector ➢ Parameters Description of RS232 communication interface: Baud rate: 38400 Data bit: 8 Parity: even parity Stop bit: 1 Default address: 1 ➢ Definition of interface pin (as shown in the below sheet): Table 4 RS232 interface pin definition description Pin Signal Description 1 2 3 4 5 6 7 8 9 NC TXD RXD NC GND NC NC NC NC Reserved RS232 data output RS232 data input Reserved Ground Reserved Reserved Reserved Reserved Remarks: If the user's computer does not have RS
User manual Figure 7 Connection Description RS232 DC 12V AC 220V Power Figure 8 Connection diagram 5. Description of Indicator Light Figure 9 Product working indicator Table 5 Product working indicator status and description Indicator Status Flashing red light Green light Function Description The device is powered on normally. The device detected a RFID tag or card 6.
User manual shown in the figure below: Figure 10 R-Tool connection interface Choose "COM" from [Communication] under [Search parameters]. Choose "All" for [COM name], set [Baud rate] as 38400, set [Frame] as 8E1, and set [address] as 255，and then click the search button to search for the device.
User manual 6.1. Configuration Parameters 6.1.1. System Basic Figure 12 Configuration interface for system basic ⚫ Work mode: the system work mode can be set to "Host mode" and "Auto read mode", which will take effect immediately after setting: A. Host mode: in this mode, after the device starts, it is in a passive state. It responds to and returns results by receiving commands from the host. B.
User manual ⚫ USB： A. HID Custom + Keyboard: HID custom interface + keyboard emulation output; B. HID Custom + VCP: HID custom interface + virtual serial port； Note: Keyboard emulation output: it is available in auto read mode; Virtual serial port: need to install the driver. ⚫ RS232/RS485：it needs to be powered on again to take effect after setting. (Note: this parameter is shared with RS485 interface) Bus address: this parameter is mainly used on the RS485 bus, the value range is 1-255.
User manual ④ As working LED IO: This GPIO is configured with the same function as the work indicator. ⑤ As tag-found LED IO: The GPIO is configured to output a high level when the tag is found during the inventory process. ⑥ As error LED IO: The GPIO is configured as an error indicator function. ⚫ Output port initial status: it needs to be powered on again to take effect. Output x: the default setting is low level. After the device is powered on, the default state of the output port is low level. 6.1.4.
User manual 6.1.5. Inventory General Parameters Figure 16 Configuration interface for inventory general parameters ⚫ Basic: ① Beep when tag found: if this option is checked, the buzzer will sound when a tag is detected.
User manual Max timeout: the maximum time to read a card on an antenna; ⚫ Special application: ① Disable Anti-collision: Disable anti-collision doesn't mean reading only one tag. If it is an inventory of 1 slot, it can read up to 2 tags after turning off this function. If it is an inventory of 16 slots, turning off this function can read up to 16 tags. ② Disable stay quiet: If the feature is checked, it will not sleep after the tag inventory.
User manual ① Block size: the number of bytes per block, NXP ICODE SLI series chips are 4 bytes per block; ② Read block command: for unrecognized tags, we do not know whether it supports reading single block and reading multiple blocks, if both are supported, then choose to " Read multiple blocks"; ③ Write block: Command：for unrecognized tags, we don't know whether it supports writing single block and writing multiple blocks, if both are supported, then choose to "Write multiple blocks". 6.1.7.
User manual Figure 19 Configuration interface for data source ① Data field select: UID: whether to output the 64-bit unique serial number of the discovered tag; User block: whether to output the data block content of the discovered tag; Antenna ID: whether to output the antenna ID of the tag; Input status: whether to output the status of the input port; ② Data field parameters: ➢ UID Length: The default is to output all 8 bytes.
User manual ➢ Input port select: Input x: checking indicates that the state of the port is to be read, but the "Input status" in the "Data field select" must be checked firstly. ③ Data format: ➢ UID data format: A. Raw bytes output: without any conversion, directly output 64-bit data stream; B. Hex string output: each byte outputs 2 hexadecimal characters; C. Lower 3 bytes integer character output: the lower 3 bytes of the serial number are converted into a decimal string; D.
User manual ⚫ Trigger: Figure 20 Configuration interface for trigger ① Trigger way: Periodic trigger, trigger reading data every N milliseconds; ② Periodic trigger parameters: Internal(ms): trigger with an interval of N milliseconds; Inventory count(0 means once): how many times to inventory after triggering. ⚫ Filter: Figure 21 Configuration interface for filter UID effective time(100ms): It only outputs once when reading the same tag within the valid time. Guangzhou Andea Electronics Technology Co.
User manual ⚫ Serial output parameters: Figure 22 Configuration interface for serial output parameters ① Output port select: A. None: read-only does not output any data; B. RS232: output data through RS232 interface; C. HID Custom: output data through the HID Custom interface. If use this interface output, the USB interface must be enabled; D. HID Keyboard：The output characters are output in the form of keyboard emulation, without any software support.
User manual ② Data frame definition： Frame option: frame header + data field + separator + data field + Terminator; ✓ Enable header: whether to output the frame header byte; ✓ Enable separator: when the output data contains multiple fields, if the item is checked, the fields are separated by a separator, such as the comma separator "E004050102030405, 01"; ✓ Enable Terminator: whether to output the terminator; ✓ Separator: whether to use the system separator or the custom separator; ✓ Terminator: wh
User manual ① Reverse UID: the sequence number contained in the data packet of the inventory command is reversed; ② Enable buffer mode: If checked, the buffer mode is used; if not checked, the asynchronous output mode is used. Buffer mode: buffer the read tags in the memory of the reader, and output them after the inventory is finished. Asynchronous output mode: it will be output a data packet with a serial number when a tag is read every time, the end package is output after the inventory is completed.
User manual ① Enable: If it is enabled, after the RF is turned on, it will be turned off when Idle time exceeds the set time. ② RF idle time(100ms): timeout. Note: after the "Auto close RF power" function is enabled, the operation of password authentication for the tag may cause failure. 6.2. Testing 6.2.1.
User manual ③ ④ ⑤ ② ① Figure 25 Single tag operation test steps Note: Step 1: In the software main interface, select the menu "Single Tag Test"; Step 2: In the "Single Tag Test" interface, select the type of tag to be operated; Step 3: mode: none address, address. 1) For a single tag, select the "none address" mode. 2) For multiple tags, select the "address" mode. Step 4: Click the "Inventory" button to display the UID list in UID drop-down box.
User manual Steps: 1) Set the data block of the tag to be operated in the Addr drop-down box and the Num drop-down box.
User manual 1 RF power protection Voltage standing wave ratio is too high 2 Antenna error Antenna parameter configuration error or offset 3 Antenna circuit protection The antenna interface is configured output with electricity , which is inconsistent with the actual antenna 4 RF configuration failed RF configuration failed 7.2. Temperature If the temperature is too high when the device is running, it will affect the work of the device.
User manual Figure 29 Noise check ➢ Interference source analysis (1) Power adapter: laptop power supply, display power supply, LED light power supply, surveillance camera power supply, electric car charger, power supply of other electric equipment. (2) Card reader with the same frequency band: access card reader, desktop card issuer. (3) Motor equipment. ➢ Troubleshooting Turn on the Noise Detection function, and switch off the power of the interference source one by one.
User manual Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Guangzhou Andea Electronics Technology Co., Ltd. Address: Room 401, Building H, Jingye San Street, Yushu Industrial Park, Economic And Technological Development Zone, Guangzhou. Zip code: 510663 Phone: 0086-20-32039550, 32039551, 32039552 Fax: 0086-20-32039553 Website: http://www.gzandea.
