Version:1.0 User Manual Blood Pressure Monitor LS808-B Arm Type Contains FCC ID: OU9AW8001-LS GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTD Zone A, 5/F., Investment Building, No. 12, Huizhan East Rd., Torch Development District, Zhongshan, Guangdong, 528437, China Thank you very much for selecting TRANSTEK Blood Pressure Monitor LS808-B.
TABLE OF CONTENTS Table of Contents INTRODUCTION ............................................................. 2 General Description Indications for Use Measurement Principle Safety Information LCD Display Signal Monitor Components BEFORE YOU START ........................................................7 Power Supply and Charge Power Setting the Time,Date and Unit Pair up with Your Device Tie the Cuff MEASUREMENT .............................................................
INTRODUCTION INTRODUCTION General Description * Thank you for selecting TRANSTEK Blood pressure Monitor (LS808-B). The monitor features blood pressure measurement, pulse rate measurement and the result storage. The design provides you with two years of lifetime. * This manual contains important safety information and caution, and provides step by step instructions for using the product. * Please do read this user manual carefully and thoroughly before use. FEATURES: 86.
INTRODUCTION CAUTION This device is intended for adult use only. This device is intended for no-invasive measuring and monitoring of arterial blood pressure. It is not intended for use on extremities other than the arm or for functions other than obtaining a blood pressure measurement. Do not confuse self-monitoring with self-diagnosis. This unit allows you to monitor your blood pressure.Do not begin or end medical treatment based solely physician for treatment advice.
INTRODUCTION BEFORE YOU START Power Supply and Charge Power Monitor Components DC POWER SOCKET ON/OFF BUTTON 1. The battery of LS808-B is built-in rechargeable li-polymer battery, the battery current is 1000 mAh. 2.
BEFORE YOU START BEFORE YOU START Setting the Time,Date and Unit To ensure the stored measurement result has correct time record, please set time and unit before device is used. (3) Press “User 1” button again to confirm [HOUR]. Then the numeral representing [MINUTE] blinks. Before use,switch the button to the “ON” side to turn on the monitor. Note: If the button is on the “OFF” side, there is no reaction when you press any button.
BEFORE YOU START (5) Repeat step 2 and 3 to confirm[MONTH], [DAY] and [YEAR]. BEFORE YOU START (7) After confirming the measurement unit, the LCD will display “dOnE” and the monitor will shut off. (6) Repeat step 2 and 3 to confirm the measurement unit.
BEFORE YOU START BEFORE YOU START Pair up the Blood Pressure Monitor with Your Device Tie the Cuff (1) Turn on Bluetooth and the app. Make sure both are on when pair-up is proceeding. (2) When the monitor is off, press and hold the User 2 button to start pair-up. The symbol and the symbol will be shown on the LCD alternatively, indicating pair-up is proceeding. If succeed, symbol If fail, symbol will be shown on the LCD. will be shown on the LCD.
MEASUREMENT MEASUREMENT Inflating and measuring. Start Measurement Display and save the results. The data transmission will proceed. When the monitor is off, press User 1 button to turn on the monitor and it will finish the whole measurement, and then save the measure data for User 1. The same to the User 2. (1) When the monitor is off, press the User 1 button to turn on the monitor. LCD display Adjust to zero. (2) Press User 1 button to power off, otherwise it will turn off with one minute.
DATA MANAGEMENT Recall the Records (1) When the monitor is off, press “Query” button to access the memory. DATA MANAGEMENT (4) When in the memory mode, press the User 1 button to recall the measurement history of User 1, or press the User 2 button to recall the measurement history. (2) The LCD will display the latest measuring result of the user ID which completes the last measurement. The record number, measuring date and measuring time will be displayed alternatively.
DATA MANAGEMENT Delete the Records DATA MANAGEMENT (3) The LCD will display “dEL dOnE” and then shut off. (1) When under the query mode, press and hold “Query” button for 3 seconds to clear the memory. (2) When the LCD display “dEL ALL”, press “Query” button to confirm. (4) If you wish to stop clearing the memory, you may press the other button, rather than “Query” button to turn off the monitor, or wait until the monitor shuts off. CAUTION 1.
INFORMATION FOR USER INFORMATION FOR USER Maintenance To obtain the best performance, please follow below instructions. Tips for Measurement It can cause inaccuracy if the measurement is taken in the following circumstances. Within 1 hour after dinner or drinking Within 20 minutes after taking a bath Put in a dry place and avoid the sunshine Avoid immersing it in the water. Clean it with a dry cloth in case. Avoid shaking and collision.
ABOUT BLOOD PRESSURE ABOUT BLOOD PRESSURE What are systolic pressure and diastolic pressure? When ventricles contract and pump blood out of the heart, the blood pressure reaches its maximum value in the cycle, which is called systolic pressure. When the ventricles relax, the blood pressure reaches its minimum value in the cycle, which is called diastolic pressure.
TROUBLESHOOTING SPECIFICATIONS This section includes a list of error messages and frequently asked questions for problems you may encounter with your blood pressure monitor. If the products not operating as you think it should, check here before arranging for servicing. PROBLEM SYMPTOM REMEDY No power Display will not light up. Power is exhausted. Charge the power Low batteries Display is dim or shows Power is low.
COMPLIED STANDARDS LIST ATHORIZED COMPONENT Athorized Component Please use the TRANSTEK authorized adaptor Complied Standards List Risk management ISO/EN 14971:2012 Medical devices — Application of risk management to medical devices Labeling ISO/EN 15223-1:2012 Medical devices. Symbols to be used with medical device labels, labelling and information to be supplied.
FCC STATEMENT EMC GUIDANCE FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
