User's Manual

6+
1.5V“AA”
1.5V“AA”
USB
The materials, specifications, parts and packaging mentioned in this manual are for
reference purposes only. We are not responsible for any changes made to this printed
material, nor are we able to inform customers of any updates or changes. Please refer
to our website: R3VOLT.COM for the latest information.
Important safety information
Thank you for buying this REVOLT item. To ensure that you operate the vehicle correctly, please read these
instructions carefully before first use and store them in a safe place for future reference.
Safety information
*Keep the smaller-sized accessories out of the reach of children.
*Do not store batteries in a hot environment (e.g. near open flames or a heating device).
*Children must be supervised by an adult when operating the vehicle. The vehicle should always remain within the
line of sight of the driver (or instructor).
*Do not recharge non-rechargeable batteries. When installing or changing the batteries, ensure that they are
connected in the correct polarity. Do not mix old and new batteries or different types of batteries.
*Do not short circuit the battery terminals.
*If you do not plan to use the vehicle for at least 10 days, discharge the battery to 40%-50% (i.e. if the battery is fully
charged, drive the vehicle for half of the total driving time). This helps to prolong the lifespan of the battery.
*You must only use the charging cable provided. Disconnect the model from the charging cable before cleaning .
Regularly inspect the charging cable’s wires, plug socket, outer casing and other accessories to ensure that they are
not damaged.If there are any signs of damage, discontinue use immediately until the fault has been repaired.
*After use, ensure that the vehicle and remote control are switched off and remove the batteries in the remote control.
*The packaging and this manual contain important information and should be kept in a safe place for future reference.
Repair and maintenance
*Clean the product regularly with a clean, soft cloth.
*Avoid exposing the product to direct sunlight or heat.
*Do not submerge the product in water, as this may damage the electrical components.
About this product
Specifications
Remote controlled vehicle
Weight 64.5g (including battery)
Dimensions 13.5x8x5 cm
Remote control range 15-20m
Operating temperature 0 to 40 °C
Battery 3.7V 200mAh rechargeble battery (included)
Remote control
Operating frequency 2.4 GHz
Operating temperature 0 to 40 °C
Battery Requirements 2x AA 1.5V Batteries (not included)
Ramp
Weight 25g
Dimensions 19x11x7.5cm
Safety information:
1.Switch off the product before charging the battery, and then connect the USB charging cable (ensure that the
charging connector is connected in the correct orientation).
2.Connect the USB charging cable to a mobile USB charger or computer USB port. The indicator light on the USB
charging cable will turn on to indicate that charging is in progress and switch off when charging is complete.
3.Pairing instructions: Switch on the vehicle. The indicator light will start to flash. Switch on the remote control and
wait for the remote control indicator to flash. The devices will pair automatically and the indicator lights will switch off
simultaneously when pairing is complete. After use, switch off the vehicle and remote control to preserve battery power.
Charging the vehicle battery
Installing the remote control batteries
LED indicator
Important:
only use the charging cable provided.
Charging the built-in vehicle battery
charging socket
Operating the vehicle and remote control
Programming a sequence of movements
1.The remote control can be programmed to perform a sequence of movements. After pairing the vehicle with the
remote control, enter programming mode by holding down the programming button for 2 seconds until the LED
indicator starts to flash. Example: Forwards + turn left + turn right, reverse + turn left + turn right, forwards + reverse
+ turn left. You can program up to 14 movements.
Fig 1. Hold down the programming button to
enter programming mode
Fig. 2 Programming a sequence of
movements
Turn right
Turn left
Forwards
Increase speed
Programming button
Flashing indicator
2.After programming the desired movements, press the programming button to exit programming mode.
The LED indicator will switch off.
3.To perform the programmed sequence of movements, press the programming button.
4. To reprogram the sequence of movements, follow the instructions in figure 1.
Note:
①The remote control will automatically exit programming mode after 8 seconds of inactivity. If you entered
a sequence a movements, the sequence will be automatically saved.
②If you did not enter a sequence of movements, the remote control will automatically retain the most
recently programmed sequence.
③To stop the vehicle when it is performing your programmed sequence of movements, move the forwards,
reverse, left or right controls.
④If the remote control batteries are depleted when you attempt to program a sequence of movements,
your sequence will not be saved. If this occurs, replace the batteries and try again.
Address: Intersection of Xingye Road No. 2 (West side) and Xingye Road (North side), Laimei Industrial
Park, Chenghai District, Shantou, Guangdong Province, China
Sales hotline: [phone], After-sales hotline: [phone]
Fax: [phone] Zip code: 515800
The manufacturer the right to the final interpretation of this instruction manual.
The vehicle will perform
the programmed sequence
of movements
Fig. 3 Performing a programmed sequence of Programming mode
Press the programming
button again
Programming
button
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules These limits are designed to provide reasonable prote-
ction against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not \installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
Warning: Changes or modifications to this unit not expressly app-
roved by the party responsible for compliance could void the users
authority to operate the equipment.
“This device complies with FCC radiation exposure limits set forth
for general population(uncontrolled exposure).This device must not
be collocated or operating in conjunction with any other antenna or
transmitter.”
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interfe-
rence to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
is in compliance with the essential requirements and
other relevant provisions of Directive 2014/53/EU.”
A copy of the full DoC is attached.
· Remove the screw from the battery compartment cover.
· Slide to open the battery compartment.
· Insert 2 x AA 1.5V batteries (not included).
· Make sure to observe the polarity symbols inside the
battery compartment and insert the batteries accordingly.
· Replace battery compartment cover and screw.
User Manual
forwards/backwards
←Forwards
→Reverse
(speed is adjustable)
Important:
Ensure that the power switch is in the “ON” position,
otherwise the vehicle will not respond to the remote control.
On/off Switch
turn left
ON/OFF
Programming
button
turn right
LED indicator
Reverse
Forward
Decoration of Conformity Inserts：
“Hereby, GuangDong Syma model drone Industrial co, ltd, declares
that this TG1007
Oper at i on Fr equency: 2410MHz t o 2473MHz
MAX OUTPUT POWER: 7. 125dBm（f or EU）