I t Instruction ti M Manuall 22-Channel Handheld Two-Way-Radio (Walkie Talkie) SAMCOM FWCN30A Main Features ● ● ● ● ● ● ● ● ● ● ● ● ● ● Frequency: 462.5500~467.7125 MHz High/Low TX Power (0.5W/0.112W) Selectable 22 channels 154 codes (50 CTCSS & 104 CDCSS) 5 km optimal range Group function (Dual-Channel Watch) 3 VOX levels 10 Call tones Monitor S Scan Key lock function Built-in 1200mAh Li Polymer Battery Flashlight NOAA & Wheather Alert Facebook SANCON INC.
Overview 12 13 6 1 3 8 14 2 9 5 10 4 11 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. LCD display Earphone & Charger Jack y Push-To-Talk ((PTT)) key Up / Monitor key Down / Scan key Power / Volume Knob Group /Ok key Menu / WX key Call Tone /Key-Lock /Key Lock key Microphone Speaker Antenna Flashlight LED Flashlight key ● GROUP Button – A broadcasting function (one-to-all) to communicate with all other radios that are programmed to monitor the same group channel (default group = CH 8).
Keep press 3 seconds the key to lock, press the key call function will opened Press the GROUP key to speak to all channel ,
GENERAL OPERATIONS Install / Removing Belt Clip Installing Belt Clip ● Slide the Belt clip into the slot A “click” indicates the Belt Clip p is locked into p position. Removing Belt Clip ● Pull the belt clip latch forward ● While pulling the belt clip latch, push up the belt clip Battery on First Use Since batteries leave factory without a fully charging, please charge the new batteries before using. Under normal circumstances, the battery on first use needs 5 hours of charging.
Notes: 1. When charging, the temperature should be between 5 ℃ ~40 ℃ ,otherwise it may cause the leakage or even damage the battery. 2. Please shut down the transceiver with battery loaded before charging it. The use of the transceiver while charging is ongoing will affect the normal battery charging. 3 Do not put back and charge the battery that is already full 3. full, for it will significantly reduce the cycle life life. 4.
Charging with AC/DC adaptor ● Plug the adaptor into the wall socket and other end into the micro USB socket on the of the radio. ● The LCD “Battery” Battery Icon will flash flash. ● Each adaptor can connect 2 sets of radio for charging. ● To charge fully from empty require about 5 hours. ● After charged, unplug the adaptor from the socket WARNING ● To avoid damage to the radio use only original accessories. ● The radio will be slightly warm during charging. GENERAL OPERATIONS 1 1.
●Rotate the PWR/VOL control knob clockwise until a" ka-ka "sound is heard to turn on the power. When you receive calls ,the knob provides you the ability to change the volume for your listening habits.When shutting down the transceeiver,you need to rotate it counterclockwise a "ka-ka" sound is heard. 3. MAKING COMMUNICATIONS The radio has 22 main frequencies and 154 CTCSS/CDCSS codes You can communicate with any other user who is using the same combinations, providing they are within range. 4.
You can use 1 of 10 different “Call Tones” to get attention of other user on the same channel with same code. and your call tone will be sent. ● Press the CALL key and the tone will sound, LCD will display the transmit icoTX 9. SCANNING CHANNELS ● Press the SCAN key once and LCD will display ● LCD display shows the scanning channel one by one. ● It will stop p at those channels with signal g for a while. 10. MONITOR Function ● Press and hold the MONITOR and radio will start scanning.
Main Screen → Main Channel → CTCSS/CDCSS → GROUP (Dual-Channel Watch) → VOX → Call Tone → Key Beep → Roger Beep → Main Screen 9. SELECT CHANNEL To select the main channel ● Press the MENU key once, Main channel number will flash. to select new Main channel or ● Press ● Press the GROUP/OK or PTT key to confirm and revert back to the main screen, or the MENU key to confirm and continue next function setting. You have 10 seconds to decide before auto-reverting back to the main screen 10.
Please speak close to the mic in order to activate VOX function. 14. SELECTING CALL TONE icon and call tone number will flash. ● Press the MENU key 5 times, LCD will display or to scroll between 1 to 10 and to select a call tone or turn off the CALL function. ● Press ● Press the GROUP/OK or PTT key to confirm and revert back to the main screen, or the MENU key to confirm g and continue next function setting. 15 KEY BEEP ON/OFF The unit has the function to turn the key beep on or off. icon.
Exiting the WX Mode for 3 seconds to exit WX mode and return to two-way radio mode. ● In WX set mode, press and hold the key ● After the WX mode is activiated either manually or by receiving an alert, if no keys are pressed for 5 minutes, the WX mode will automatically revert back to two-way radio mode.
CDCSS Octal Code Chart Code No. 39 OCT Code 023 Code No. 52 OCT Code 074 Code No. 65 OCT Code 165 Code No. 78 OCT Code 271 Code No. 91 OCT Code 413 Code No. 104 OCT Code 565 Code No. 117 OCT Code 731 Code No.
● CAUTION A proper antenna is the antenna supplied with this radio by the manufacture or an antenna specifically authorized by the manufacturer for use with this radio. ● DO NOT Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the "TX indicator" lights red. You can cause the radio to transmit by pressing the " PTT" switch.