User Manual SAMCOM FPBN10A
INDEX User Security Information --------------------------------------------- 3 Specification ------------------------------------------------------------ 11 Feature ------------------------------------------------------------------- 11 Products Inspection --------------------------------------------------- 12 Get familiar with the transceiver ------------------------------------ 13 Battery Information ---------------------------------------------------- 14 Disassembly and Reassembly -----------------------
Troubleshooting Guide Problems No Power Battery may have been exhausted. Please update or recharging the battery. Battery may not be installed correctly. Please remove the battery and reload it. Battery lasts no long after charging Battery’s lifetime is due. Please update the battery. Battery is not charged fully, so please ensure that the battery indicator is green when removing it.
Handheld Transceiver Safety Guidelines and Instruction To control the transceiver radiation, ensure to meet the general or non-controlled environment radiation limitation standard, please operate following below procedures. Press PTT key when talking; and release PTT key when receiving. Because measured RF energy radiation will be generated when transmitting, so transmitting time should not exceed 50% of the using time.
Voice compression and expansion This feature ensures the user in a variety of noisy environments can get a clear call. Set by the dealers in the channel through programming software. Scrambler This feature is voice encryption, user no such feature can not receive the real voice, so makes your call be kept confidential. This feature may be set by dealers in the channel through programming software. DTMF encoding This transceiver has DTMF encoding function.
Medical devices Pacemaker Busy Channel Lockout Advanced Medical Technology Association of the United States proposes holding the handheld transceiver with pacemakers should be kept the distance of at least 6 inches (15cm). These proposals are consistent with the provisions by the U.S. Food and Drug Administration. This feature can prevent interferences to other walkie-talkies in the same channel.
When the function is activated, the transceiver will check whether there are calls on the channels that are set to be scanned. If a channel is tested to have signals on it, it will switch to this channel in order to receive voices (which channels can be scanned is programmed and set by dealers). Priority Scan This feature allows you to scan frequently used channel. Dealers can set priority channels by programming software. If you want more information, please contact the dealer.
Fuse and blasting areas To avoid possible interference with blasting operations, please switch off your transceiver when get close to blasting areas and areas where deployed some detonators. Those places posted with the words to switch off wireless radio, you have to turn off it. Please observe all signs and instructions.
Volume Adjustment As this type of transceiver has an auto-squelch function, you will hear nothing when the power is turned on and no call is received. You can hold down the MONI button, and then turn the PWR/VOL knob clockwise to increase the volume, or counterclockwise to decrease it. Monitoring To monitor, you need just hold down the MONI button and adjust the channel background noise to a comfortable level by rotating the PWR/VOL knob.
Charging Equipment Notes 1. Do not expose the charger to rain or snow. 2. Chargers by severe impact, or has been dropped, or subject to any damaged, do not use again. 3. Can not disassemble the chargers by severe impact, or has been dropped, or subject to any damaged. 4. Can not replace the original power cord and plug provided. If plugs and sockets do not match, please ask the qualified electrician to install an outlet to avoid electric shock. 5.
2. Removal of the belt clip As for the removal of the belt clip, please refer to the installation steps and loose the screws in conterclockwise. Installation/Removal of External Earphone or Microphone 1. Installation of the external earphone or microphone Specifications and Parameters General Specifications Channel capacity 16 groups of memory channels CTCSS CDCSS 50 QT 105 DQT Frequency stability ±2.5PPM Antenna Impedance(Ω) Operating Temperature 50Ω -20 ~ +50 Power supply(V) 7.
Products Inspection Welcome to use FPBN10A transceiver, and before using, we recommend you: Please open the giftbox carefully to confrim whether the items as following table are all included; if you find any things lost or damaged, please contact immediately with the dealer. Installation /Removal of Antenna 1. Installation of the antenna ⑴ Plug the screw-thread end of the anenna into the socket at the top of the transceiver. ⑵ Rotate the antenna clockwise until tightening up , as shown below.
3. Place the battery or the transceiver with battery on the charger. 4. Confirm that the battery contacts are well connected with the charger contacts, and the charge indicator light turns red, which represent the beginning of the charging operation. 5. After a period of time, when the indicator light turns green, it shows the completion of the charging operation. Get Familiar with the transceiver Disassembly and Reassembly Installation/Removal of the Battery 1.
Battery Information Battery on First Use Since batteries leave factory without a fully charging, please charge the new batteries before using. Under normal circumstances, the battery on first use needs 5 hours of charging. The first three times of fully charging and discharging provides batteries the best capacity. When you find out the battery is low, it is required to charge or replace it.
SAFETY TRAINING INFORMATION Your SAMCOM radio generates RF electromagnetic en-ergy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, Warning and the ways to minimize such hazards. This radio is not intended for use by the “General Population” in an uncontrolled environment.
this radio by the manufacturer or an antenna specifically authorized by the manufacturer for use with this radio. • DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch.