User's Manual
1 2
3
4 5
WiFi Video Doorbell
USER MANUAL
NOTE: Or, you can buy the accessories
from the store near you by yourself.
Sub-unit
*1
1.5W
solar panel
WIFI doorbell
*1
Rain shade
*1
TF card
16G
*1
2PIN
flat cable
*1
Screw
Pack
Version 1.0
RL-IP09D-LOCK
1
3
2
RL-IP09D RL-IP09D-DC
What's Included
18650
rechargeable
lithium battery
*2
Micro usb cable
1
2
3
0
1
0
Low power consumption 2.4GHz WiFi doorbell.
Two Removable 18650 lithium batteries.
Powered by a solar panel or an external power
adapter.
IP44 rating.
Two million pixels, 110°wide viewing angle.
Removable TF card.
PIR motion detection.
Motion detection with High/Medium/Low sensitivity
setting.
Tamper alarm function.
Support a 433MHz wireless door chime connection.
NOTICES
When choosing the location for the solar panel,
make sure it will get as much direct sunlight to
fall upon it as possible.
For the first use, make sure the batteries are
charged for 10 hours before use. During charging,
place the device on a flat desk so that the desk
can crush against the tamper switch or use an
adhesive tape to crush against the tamper switch.
Make sure the PIR sensor is not exposed to the
direct sunlight.
Do not install the device at the location where
people are frequently moving.
Make sure the device is close to your router,
otherwise, the video quality may be affected.
Remove the insulation sheet from the battery
compartment.
A. WIFI doorbell installation
1. Fasten the rain shade on the wall with screws.
(1.4-1.6m high from the ground, Screw size:
4*40BA)
2. Connect the wires according to the wiring diagram.
3. Fix into the rain shade and fasten the bottom with
screws.
Installation Instruction
Features
insulation
sheet
1
Configuration
Powered by a mobile phone adapter (with a micro
USB cable), it only provides a dry contact signal for
unlocking, therefore, an additional power supply
for unlocking is required.
B. Wiring Diagram
Electric
Lock
Make sure the doorbell has
batteries installed.
Powered by a mobile phone
adapter
Mobile phone adapter
2
DC 6V
Electric
Lock
Power supply for
unlocking
1.5W solar
panel
Make sure the doorbell has
batteries installed.
The solar panel must receive
as much direct sunlight over the
course of the day as possible.
Configuration
Powered by a mobile phone adapter or a solar
panel, however, it cannot be powered by both at
the same time. This configuration only provides a
dry contact signal for unlocking, therefore, an
additional power supply for unlocking is required.
3
Power supply for
unlocking
Electric
Lock
Configuration
This configuration does not need charging. Simply
connect the power adapter to make it work. This
configuration only provides a dry contact signal for
unlocking, therefore, an additional power supply
for unlocking is required.
AC & DC12-24V/1A
Power supply for
unlocking
If installed into the rain shade,
remove the device from the rain
shade for charging, 8 hours at
least for charging.
1 1 0
B. Sub-unit
Light-dependent
resistor (LDR)
PIR
Adapter port
USB port
TF card
Lock connection
Tamper alarm switch
Battery compartment
Production Introduction
Camera
A. WIFI Doorbell
Call button
TuyaSmart
Android 5.0 / iOS 8.0 or higher
Downloading the APP
1. Go to APP Store or Google Play to download the
"TuyaSmart" APP. After download, install it.
2. Or, scan the QR code below to download and then
install it.
RESET
Microphone
LED light
C. Pairing Devices
Insert batteries for the sub unit, Long press " " on
the sub unit for over 3 seconds, it will sound "Ding -
Dong" to indicate that it has entered into the pairing
state. Now, press the Call button on the WiFi doorbell
(the button indicator light will be turned on), when the
sub unit sounds the melody selected, and at the same
time the indicator light flashes blue, the pairing is
successful
Speaker
Learning Code
Clearing Code
Indicator
Melody Selection
Work Mode
Volume Button
Working indicator: When working, the indicator light
will blink red.
Low battery indicator: When the voltage is less than
3.3V, the red indicator light will stay on.
NOTE: When the light indicates low battery, please
replace batteries timely.
Indicator Light
Work Mode
Press " " on sub unit to select the mode. There the
are 3 modes for option:
1. Silent and blink, 2. Ring without blink, 3. Ring and
blink.
(38 melodies
for option)
(Mute/Low/
Medium/High
four levels for
option)
Long press " " on the sub unit for over 5 seconds, it
will sound "Ding-Dong, Ding-Dong"
to indicate that clearing code is successful
Indicator Light Explanation
Flash red and green alternately: Charging the batteries.
Flash red: Waiting to configure the network.
Flash green rapidly: Configuring the network.
Stay green: Working.
Yellow (lighting red and green at the same time):
Powered by an external power supply, charge
completed, no batteries detected. (NOTE: If no
batteries installed, the indicator light will only be
yellow.)
Red and green light off: Low power consumption
standby status.
Technical Parameters
Video resolution : 2M Pixels
standby current : ＜1.5mA
Battery capacity : 2200mAH/pcs
Solar panel : 1.5 W
TF card storage : Max. 64G
PIR sensitivity : L/M/H
Intercom volume(30cm) : ≈80dB
Alarm volume(30cm) : ≈85dB
Video recording length : 15S
Operating temperature : -10~50°C
WIFI distance : approx.80m (Open area)
Battery : DC4.5V(1.5V/AA/LR6*3)
Standby current : Max. ≤ 4mA; Average ≤ 0.25mA
Working current : Max.＜150mA; Average＜100mA
Volume (30cm) : ≈85dB
Frequency : 433.92MHz ± 250KHz
Distance : approx.80m (Open Area)
Working temperature : -10~50°C
Demodulation : OOK
B. Sub-Unit
A. WIFI doorbell