WM-8710BNSIP WIFI Module Manual 1 Gener al I nf or mat i on category WIFI Module Drawing Number MW-8710BNSIP Model MW-8710BNSIP Environmental requirements RoHS,REACH Number 17164200000522 Electrostatic level Contact discharge+/-4KV,Air discharge +/-8KV Certification number FCC ID:2ARD9-501 IC :27775-501 2 Technical information The scheme is based on RTL8710BN(W302)and uses few peripheral components to realize the conversion from UART to WiFi signal。 2.
Product back view 2. 2 Di mens i on definition Length Width Thickness dimension(mm) 20 15 1.0 error(mm) ±0.2 ±0.2 ±0.2 PIN length 3.6mm±0.2mm 2. 3 PI N name Pin No. 1 2 3 4 WiFi module pin description VCC:Power supply pin RXD:Signal receiving pin TXD:Signal transmitting pin GND:System ground PIN 2.
2. 5 Parameters No. performance parameter technical requirement 1 MCU RTL8710BN(W302) 2 Operating frequency 2412 - 2462 MHz 3 Supported WiFi standards 802.11b/g/n(1T1R) modulation mode 802.11b: DSSS (CCK, DQPSK, DBPSK) 802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK) 802.11n HT20: OFDM (64QAM, 16QAM, QPSK, BPSK) 802.11n HT40: OFDM (64QAM, 16QAM, QPSK, BPSK) 5 Supported rate 11b: 1, 2, 5.
Specification IEEE802.11b Mode DSSS / CCK Channel CH1 to CH13 Data rate 1, 2, 5.5, 11Mbps DC Characteristics Min. Typ. Max. 单位 229 mA 备注 1.DC current (Average) @5.0V input 1) TX only @17dBm 2) TX throughput mode - 120 mA 3) RX throughput mode - 100 mA TX Characteristics Min. Typ. Max. Unit 15 17 18 dBm 1) fc +/-11MHz to +/-22MHz - - -30 dBr 2) fc > +/-22MHz - - -50 dBr -25 0 +25 ppm Min. Typ. Max.
1) 6Mbps - - -5 dB 2) 9Mbps - - -8 dB 3) 12Mbps - - -10 dB 4) 18Mbps - - -13 dB 5) 24Mbps - - -16 dB 6) 36Mbps - - -19 dB 7) 48Mbps - - -22 dB 8) 54Mbps - -30 -25 dB 5 Frequency Error -25 0 +25 ppm RX Characteristics Min. Typ. Max.
3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - -30 -28 dB -25 0 +25 ppm 5. Frequency Error RX Characteristics Min. Typ. Max. Unit 6.
5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - -30 -28 dB -25 0 +25 ppm 5. Frequency Error RX Characteristics Min. Typ. Max. Unit 6.
another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: 2ARD9-501” any similar wording that expresses the same meaning may be used. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
brouillage est susceptible d’en compromettre le fonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 27775-501” any similar wording that expresses the same meaning may be used.
emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.