Specifications

· Excessive sound pressure from earphones and headphones
can cause hearing loss, hearing damage risk, high sound
high sound pressure.
· For health reasons, avoid listening on high volume for
extended periods.
· RF exposure information: The EIRP power of the device
at maximum case is below the exempt condition, 20mW
specification in EN62479: 2010. RF exposure assessment
has been performed to prove that this unit will not generate
the harmful EM emission above the reference level as
specified in EC Council Recommendation (1999/519/EC).
Manual｜Warranty Card
Device Layout
Package Contents
Wearing Instructions
Please wear the headset as shown in the picture below.
* Remark: please do not put the sound-producing unit into
your ears.
Use of On/Off Button
Power On
Power Off
· Press the On/Off button for 2 seconds in the power-on state,
and the red light will light up for 1 second and then goes off,
and the headset is powered off.
Answer Calls
· When there is a call, press the On/Off button to answer the
call.
Hang Up
· Press the On/Off button to hang up during the call.
Decline
Reject Calls
· When there is a call, press the On/Off button for 2 seconds
to reject the call.
music is paused.
· When playing music, press the On/Off button to pause.
Wearing Detection
· Music pauses automatically when detected that the headset
has been taken off; play music automatically when the
headset is worn.
Charging & Reminder
Low Battery Alarm
· In the working state, when the battery level is less than 20%,
the red light flashes every 3 seconds until the headset is
automatically turned off. When the battery level is less than
10%, the headset will give a low battery alert sound.
* The above data is the test results under the standard laboratory
environment. The actual situation of data and parameters will vary
slightly depending on the test environment, test software and
other factors.
Accept
Ear-care Headset ×1
Manual & Warranty Card ×1
Charging Cable ×1
1. On/Off
2. Indicator Light
3. Micro USB
Time Required for Charging: About 1 hour (At room
Rated Output Power: ＜8dBm
temperature)
Specifications
Model: E2001AO
Bluetooth: Bluetooth 5.0
Bluetooth Working Frequency: 2400-2483.5MHz
Effective Range of Bluetooth: 10m
Audio Distribution: SBC/AAC coding
Battery: 3.8V/185mAh
Frequency Response Range: 20Hz-20KHz
Available for: About 8 hours (It varies slightly based on the
volume of the songs being played)
AL
· Please comply with the relevant regulations of the country or
region where you are. Do not use this headset while driving.
· Remember that driving safety is your primary responsibility
and do not engage in any activities which will distract you.
· The electronic equipment of your car may fail due to radio
interference of the headset. Please contact the electronic
equipment’s manufacturer for more information.
· The wireless devices may interfere with the flight system
of the airplane, please abide by the relevant regulations of
the airline and do not use the headset in places where
wireless devices are prohibited.
Traffic Safety
Connection & Use
Bluetooth Connection
1. When pairing with the device for the first time, press the On/
Off button for 7 seconds on the headset, the blue light will
light up and flash, and the headset enters the pairing state.
2. Turn on your device’s Bluetooth, find and pair with the
discoverable device “imoo Headset”. When the pairing
succeeds, the blue light of the headset will flash for every 3
seconds.
Bluetooth
MY DEVICES
imoo Headset
Automatic Reconnection
1. Press the On/Off button for 2 seconds to power on
and the headset will automatically connect to the last
connected Bluetooth device (If fails, the headset will
enter the pairing state).
2. If your device is within the headset’s Bluetooth working
scope, it will automatically reconnect. (When your device
is out of the headset’s Bluetooth working scope: a. The
connection will fail, and it will reconnect automatically
Disconnection
· Turn off your device’s Bluetooth to disconnect, and the
headset will automatically enter the pairing mode.
Operation Environment
Children Security
Maintenance
Warranty Descriptions
Service Terms
Warranty Descriptions and Attentions
Warranty Card
(The First Invoice: Sales Invoice)
User’s
Data
Warranty
Data
Product
Data
User’s Name: ____________ Telephone: ____________
Kid’s Grade: _____________
Product Model: ________________________
Machine No.: __________________________
Date of Purchase: __________________ (DD/MM/YYYY)
Site of Sales: ____________ (Store) ____________________
________________________________ (Address)
Product Model & Machine No.:
Name of Sales or Service Center:
_____________________________________________________
Warranty Category: □ Replacement
□ Repair
Reasons for Replacement/Repair: _____________________
Handled by: ________________
Telephone: _________________
Date: _______________________ (DD/MM/YYYY)
E-mail: [e-mail]
Our company is committed to continuously improving
the quality of our products, the descriptions stated in
the manual may be slightly different from the actual
product.
Please read this manual carefully before using the
product and keep it properly.
Images are for illustrative purpose only. The actual
product may vary.
1
2
3
6
7
4 5
· Press the On/Off button for 2 seconds until the blue light is on.
EU Declaration of Conformity (DoC)
· Hereby, Guangdong Genius Technology Co., Ltd., declares
that this type of equipment is in compliance with the
essential requirements and other relevant provisions of
Directive 2014/53/EU.
· The declaration of conformity may be consulted at:
https://www.imoo.com/en/pc/certification/index.html.
Waste Electrical & Electronic Equipment
(WEEE)
· This symbol means that according to local laws and
FCC Regulatory Conformance
regulations, your product and/or its battery shall be
disposed of separately from household waste. When this
product reaches its end of life, the user has the choice to
give his/her product to a competent recycling organization.
Proper recycling of your product will protect human health
· Our company will seek shared responsibility
and cooperation from customers in reducing
the environmental impact of their products.
· Our company will comply with all the applicable
laws related to WEEE management.
· This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(a)This device may not cause harmful interference;
(b)This device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure
Charging
· Use the charging cable in the package to connect the
headset and the power source for charging. While charging,
the red light flashes every 1 second. When fully charged,
the blue light keeps lighting up.
Play/Pause
· Press the On/Off button to start playing music when the
· Do not use the headest in damp places or places close to
magnetic fields, so as to avoid causing its internal circuit fault.
· It is strictly prohibited to use the headset in thunderstorm
weather, which may cause failure in it or risk of being struck
by lightning.
· Please use and store the headset and its accessories within the
temperature of 5℃~35℃. Exposure to over-high or over-low
temperature may cause headset failure.
· Do not allow the headset and its accessories to be exposed
to rain or moisture, which may cause fire or electric shock
hazard.
· Do not expose the headset to direct sunlight, such as placing
it on the car dashboard or window sill.
· Never put the headset close to the heat sources or fire, such
as placing it near the electric heater, microwave oven, oven,
water heater, stove, candle or any other places that may
produce high temperature.
· Do not place sharp metal objects such as pins near the
receiver and speaker of the headset so as to avoid injuries
caused by the adhesion of metal objects.
8
· The headset and its accessories may contain some small
parts. Please place the headset and its accessories out of
the reach of children so that children may not inadvertently
damage the headset and its accessories and avoid the risk
aused by small parts such as suffocation on children.
· This headset is not a toy. Children should use it under the
guidance of their guardians.
Attentions for Charging and Battery Use
· Due to the consideration of environmental protection, this
product is not equipped with a power adapter. You can use
the USB interface on your computer or the power adapter
with CE certificate to charge. And the output voltage and
current of the power adapter should conform
to the following specifications: output DC voltage: 5V;
output DC current: No less than 1200mA.
· Please buy the power adapter through official channels.
· Poor-quality or counterfeit power adapters may cause an
explosion or fire.
· The power adapter is a disconnecting device; the power
outlet should be installed nearby for convenient disconn-
ection. When repairing or disassembling the headset, please
unplug the power adapter from the outlet.
· Please ensure that the Micro USB is dry and without dirt
before charging.
· Never throw the battery into fire or expose it to an over-
heated environment such as sun, roasting with fire or similar
conditions to avoid leakage, explosion or fire disaster.
· Please charge the headset at 5℃-35℃ to avoid degradation
in battery performance.
· To prevent children from getting an electric shock, please
charge the headset under the guidance of parents or other
guardians.
· Keep small cells and batteries which are considered swallow-
able out of the reach of children:
(a) Swallowing may lead to burns, perforation of soft tissue,
and death. Severe burns can occur within 2h of ingestion;
(b) In case of ingestion of a cell or battery, seek medical
assistance promptly.
· Non-professionals are not allowed to disassemble the headset
without authorization. For any faults with the headset, please
contact our local after-sales service center.
· Prevent the headset from falling and avoid knocking, vibrating
or roughly treating it, which may lead to damage to its internal
circuit board and precise structure.
· Keep the headset and its accessories dry and do not use
heating tools (e.g. microwave oven, hair dryer, etc.) to dry it.
· Do not place the headset and its accessories in areas where
the temperature is too high or too low, otherwise, it may cause
device faults, fire or explosion.
· Before cleaning and maintenance, please stop using the
headset, and disconnect all connections or charging cables
from other devices.
· Do not use strong chemicals, detergents or strong detergents
to clean the headset or its accessories. Use a clean, dry and
soft cloth to wipe the headset or its accessories.
· Never keep the magnetic stripe card (e.g. bank card, SIM card,
etc.) in contact with the headset for a long time. Otherwise,
the magnetic stripe card may be damaged by the headset's
magnetic field.
9
Thank you for choosing the imoo Ear-care Headset. Our
company will provide comprehensive service assurance in
accordance with local rules and regulations. In case of any
inconsistency or omission with local policies, the local policies
shall prevail.
· Within 30 days from the date of sale, users can choose
product replacement or return for performance fault (not
caused by human factors).
· Within 24 months from the date of sale, users can enjoy
warranty service for performance fault under normal use.
· The information filled in the warranty card should be
complete, accurate and convincing. Customer should ask for
a valid purchase invoice and keep it properly.
· The premise of requesting warranty service is to have a valid
warranty card and purchase invoice (The information filled in
the valid warranty card and purchase invoice should be
complete, accurate and without alterations). If the valid
warranty card and purchase invoice are lost and a copy of the
valid invoice cannot be provided, a 24-month warranty service
will be provided since the 90th day after the date of
production of the headset.
· We provide a 6-month (from the date of sale) replacement
service for the charging cable. Other accessories (such as
gift boxes, manuals, etc.) do not enjoy the warranty service.
10
· The warranty service is only valid under normal use of the
headset. For the cases as below, we do not provide warranty
service but provide repair requiring an extra charge.
(2) This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communic-
ations. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
(a) Reorient or relocate the receiving antenna.
(b) Increase the separation between the equipment and receiver.
(c) Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
(d) Consult the dealer or an experienced radio/TV technician for
help.
(1) Exceeded the warranty period;
(2) Damage caused by human factors, including damage
caused by the use’s failure in using, operating or keeping
the product as required by the manual;
(3) Damage caused by unauthorized dismantling, mainten-
ance, repair and modifications;
(4) Damage caused by natural disasters (e.g. flood, fire,
earthquake, etc.);
(5) No valid warranty card or purchase invoice (except those
that can prove the product is under warranty);
(6) Unauthorized alterations of the warranty card; or the
product model or code on the warranty certificate is
inconsistent with the actual product;
(7) Natural wear and tear during use (e.g. shell, charging cable,
etc.);
(8) Errors, damages and defects that are not caused by the
quality of the product itself (e.g. liquid penetration, being
affected with damp, dropped, extrused by external
pressure, out of shape, being improperly used, etc.).
· Any oral agreement made by the dealer regarding the
warranty contents, which is beyond the scope of this warranty
agreement, shall not be included in the scope of warranty.
· If the product meets the requirements for replacement, you
can go to the nearest imoo official center for replacement.
During replacement, if the main machine is damaged, you can
replace it with a new one of the same model; if the accessory
is damaged, you can replace it. Both the replacement of the
main machine and accessories are for free.
· All parts, components and accessories replaced within the
warranty are owned by the company.
· Never allow children or pets to swallow or bite the headset
or its accessories to avoid injury or resulting in failure or
explosion of the headset.
Attentions
· Please read the following contents and attentions carefully
before using this product, and abide by them when using it.
We bear no liabilities for the consequences caused by the
failure to use the product correctly or abide by the relevant
instructions of this product.
Electronic Devices
· Do not use the headset in places where wireless devices
are expressly prohibited, otherwise, it will interfere with
other electronic devices or cause other risks.
Impacts on Medical Devices
11 12 13
*NOTE:
(1) This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
*NOTE:
The manufacturer is not responsible for any radio/TV interference
caused by unauthorized modifications to this equipment. Such
modification could void the user’s authority to operate the equipment.
Please read this manual carefully before using the product
and keep it properly.
only after your device is within its working scope;
b. When your device is out of the headset’s Bluetooth
working scope for too long, the headset will power off
automatically and the automatic reconnection fails.)
and the environment.
· Please observe the relevant regulations and turn off the
device in medical and healthcare facilities where wireless
devices are prohibited.
· The radio waves generated by the device may affect the
normal operation of implanted medical device or personal
medical devices, such as pacemakers, cochlear implants,
hearing aids, etc. If you use these medical devices, please
consult their manufacturers about the attentions.
· When you use the headset to listen to music or make phone
calls, it’s recommended to use the minimum volume required
for listening to music or making phone calls, so as not to cause
hearing damage. Long-term exposure to high volume may
lead to permanent hearing damage.
· Exposure to high volume while driving may lead to distraction,
which may lead to accidents.
Hearing Protection
Warranty Card
(The Second Invoice: User Invoice)
User’s
Data
Warranty
Data
Product
Data
User’s Name: ____________ Telephone: ____________
Kid’s Grade: _____________
Product Model: ________________________
Machine No.: __________________________
Date of Purchase: __________________ (DD/MM/YYYY)
Site of Sales: ____________ (Store) ____________________
________________________________ (Address)
Product Model & Machine No.:
Name of Sales or Service Center:
_____________________________________________________
Warranty Category: □ Replacement
□ Repair
Reasons for Replacement/Repair: _____________________
Handled by: ________________
Telephone: _________________
Date: _______________________ (DD/MM/YYYY)
1 2
Profiles: A2DP V1.3/AVRCP V1.6/HFP V1.7
Certification Related
Information ×1
· The SAR limit of USA (FCC) is 1.6 W/kg averaged over one
gram of tissue. Device has also been tested against this SAR
limit. Use 0mm away from the head.
EU Regulatory Conformance