4% : NS2MH9003 @ BELL SOUTH CORDLESS TELEPHONE 900 MHz FILTERED SOUND" WITH 4 CHANNEL AUTO SCAN Model MH9003 OWNER'S MANUAL INSTALLATION AND OPERATING INSTRUCTIONS PLEASE READ THIS MANUAL CAREFULLY BEFORE USE. KEEP FOR YOUR REFERENCE. For Getting Started Information, please see Installation Instructions on page 8 or your separate Quick Start guide.
ed Special Features proper care and by following the setup and user instructions in this } oC manual, this unit will provide you with years of trouble free service. s Bell South is committed to providing quality products that fit your needs. We would like to have any comments or suggestion you might have on this product, You may mail your comments to: U.S.
HANDSET ANTENNA IN BATHHOUSE, LOW — LED INDICATOR Pg.5 TALK BUTTON 10, A 14,15,17 MEMO BUTTON i ra 17 VOLUME CONTROL (HI, LOW) SWITCH Pa.5 + I CHANNEL (CH) SELECT BUTTON yi 21 PAUSE BUTTON VA FLASH BUTTON Pg.5 § YC) TONE BUTTON Pg.5 REDIAL BUTTON Pg5,15 "For Getting Started information, please see Installation instructions on page 8 or your separate Quick Start guide.
np ay 7, 0008 Safety instructions IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid : cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4.
Safety Instructions the product has been dropped or the case has been damaged. F. If the product exhibits a distinct. change in performance. 13. Do not use the telephone to report a gas leak in the vicinity of the leak. 14, Never install telephone wiring during a lightning storm. 15. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 16.
Boat. a bogie 7 HANDSET Controls 1. In Bathhouse Low LED Indicator: Lights up when the HANDSET is in TALK mode. Blinks when battery power is low. (See page 19 for detail.) 2. TALK Button: Press to answer an incoming call or to place a call. Press to end a call. 3. Memo Button: Press to store phone numbers i in memory or to call a number you have previously stored. 4. Flash Button: Press to answer ah incoming call if you have Call Waiting. 5.
Cod ag Ld NS2MH9003 BASE UNIT Controls 7. Telephone Line Connection Jack Tone/Pulse Select Switch Power-In Connection Jack Antenna: Raise for best reception. In Use/Charge LED indicator: Lights up to indicate the unit is ON or when the HANDSET is placed on the BASE UNIT for charging. It flashes to indicate the page function is in use. PAGE Button: Press to page the HANDSET. Charge Terminals: For charging the HANDSET battery. For best performance, clean periodically with a damp cloth only.
mare NET are feats dh Loe Ser Fes oon “nt FCC ID: NS2MH9003 LLY Started Connecting Your Phone This section is a reference guide to the basic functions and operations of your cordless telephone. For more detailed descriptions of the operations and features of this telephone, refer to the Contents on page 1. 1. Carefully remove your cordless telephone from its shipping carton. [there is any visible damage, do not attempt to operate this equipment. Return it to the place of purchase, 2.
The Hr . Lis — L Getting Started *: . BASE UNIT ANTENNA a TELEPHONE Co od 2 120V WALL AF wh JACK : SE . CONNECTION TELEPHONE LINE | i: ~ SOURCE I x AC ADAPTER . 5 RADIOTELEPHONE Insert the small plug on the end of the AC adapter into the POWER-IN connect son jack on the back of the BASE UNIT. : A 4. Plug the AC adapter into a 120V AC wall outlet. Fs /N\ Use only with Class 2 Power Source 9V DC, 300mA. f i 5. Insert one plug of the TELEPHONE LINE CORD into the house TELEPHONE 3.
STAT Ag EE Cad EAE sar ten Kn nN Getting Started Ign COD dos S BELL SOUTH Press the button to confirm that you have a dial tone. If you do not get a dial tone, review steps 3 through 8. If you still have no dial tone, refer to the Problem Solving section on page 21. 3 WF PSE 500 { Ane Ee Q 0 HANDSET 2 . are shh ah SAY oe en TE gel FTN a 9. Before initial use, charge the HANDSET for 12 hours. 5d . You are now ready to use your new Bell South Cordless Telephone.
Desk Mounting Desk Mounting One of the special features of your equipment is the unique design of the MOUNTING BRACKET which can hold your phone at an angle of 45° when desk mounting. There are two positions to choose from: 1. NORMAL POSITION (Mounting Bracket not required) For normal position, as shown in Figure 1, place the BASE UNIT on any desired but suitable location. NEG wn Reggie FIGURE 1 2.
bo 2 FCC ID: NS2MH9003 ERI] Mounting Preparing for Use You may choose to put the BASE UNIT of your cordless telephone on a wall. 1. With the back of the BASE UNIT facing up, connect the SHORT TELEPHONE LINE CORD to the telephone line jack. 2. Insert the top hooks of the MOUNTING BRACKET into the matching slots of the BASE UNIT (as shown below). Then push the bottom hooks of the MOUNTING” BRACKET into place. Plug the free end of the SHORT TELEPHONE LINE CORD into the MODULAR WALL JACK. 3.
Basic Operation . Preparing for Use 3 ‘ Before you can use your cordless telephone, you must charge the HANDSET for hours. Failure to do so will require recharging of the battery pack more often. ied 1. Place the HANDSET on the BASE UNIT for 12 hours. i | 2. After 12 hours, remove the HANDSET from the BASE UNIT. § 3. RAISE THE BASE UNIT ANTENNA FOR BEST RECEPTION. . Before you can use your cordless telephone, you must charge the i HANDSET for 12 hours.
Receiving Calls with the HANDSET on the BASE UNIT 1. When the phone rings, lift the HANDSET. The IN USE LED indicator will light up. (NOTE: The HANDSET RINGER SWITCH must be in the "ON" position for ringer to operate.) 2. Start your conversation. 3. To end your conversation, either press : the button or place the HANDSET » SL on the BASE UNIT. If you place the HANDSET on the BASE UNIT charge cradle, you activate the automatic STANDBY feature. Receiving Calls with the HANDSET off the BASE UNIT i. Co 1.
Placing Calls Placing Calls 1. Press the(TALK) button. The IN USE | LED indicator will light Listen for a dial tone. 3. Dial the phone number. 4, When you have finished with your ®) (2) (3) call’ press the (TALK) button again. i = 5 The IN USE LED indicator will tun | DIDO off. HANDSET Redial Feature MEMO PAUSE TONE Na 1. If you get a busy tone, press the . ! iE button to hang Later, press the button again. me 3. Listen for a dial tone. Press the (REDIAL) button.
Storing Numbers 1. Be sure the BASE UNIT IN USE LED indicator is off and the HANDSET is in STANDBY mode. (See special features section). s 2. Press the(MEMO) button. 3. Dial the number you want to store. 4. Press the(MEMO) button again. 5. Dial the index number (0-9) where you want to store that number. You will hear one confirmation beep. , 6. Write the name of the person you will be calling with that number next to the corresponding index number on the telephone number card. : 7.
Recalling | Numbers Recalling Stored Numbers from Memory 1. Press the (TALK button. 2. Press the(MEMO) button. 3. Press the index number for the number you have stored. The stored" number wil be dialed automatically. | EXAMPLE: Ti I ber 703-1968 / stored under ot on the po Press the (TALK) button. Press the (MEMO) button. DED: » — PAUSE TONE | FLASH RED, 1 ACRE OFF oN ’ TNE «5 IMPORTANT ; To obtain the best reception, be sure to raise or reposition the BASE UNIT antenna.
Nora wip x i FCC ID: NS2MH9003 rit) Security System Your cordless telephone uses a digital coding security system to prevent unauthorized use of your telephone line by another nearby cordless telephone. The system "has its own identifying signal created by microcomputers in both the BASE UNIT and HANDSET. Lo : Security Code This telephone has an internal security code with 65,536 possible combinations.
3 Fi, FCC ID: NS2MHO003 MHO0OPp 1A pa 19 Battery Type : | Use the following type and size of battery pack: . Cordless Telephone Battery Pack 3.6V, 600mAh U.S. Electronics Inc. @ & Ni-Cd Battery Pack: model B650 Ni-Cd This battery pack is available through: U.S. Electronics Service Center 105 Madison Avenue New York, NY 10016 1-800-828-5208 Recharging the Battery Pack The nickel cadmium (Ni-Cd) battery pack in the HANDSET can be recharged many times using the built-in charger in the BASE UNIT.
i vr : FCC ID: NS2MH9003 Whelp 1A pb 20 Changing the Battery Pack The battery pack provides power for the HANDSET of your cordless telephone. To Replace the Battery Pack: | : 1. Remove the HANDSET battery compartment cover by sliding it down. 2. Pull out the battery connector and remove the battery pack. 3. Plug the new battery pack into the battery connector. 4. Slide the HANDSET battery compartment cover firmly into place in its closed position. : . 5. Before use, charge the new battery pack for 12 hours.
es “FCC ID: NS2MH9003 Problem Solving Problem Solving Section For your assistance, we have listed below a few common problems. Phone does not work, check the following: 1. BASE UNIT is plugged into power source. 2. HANDSET is charged. 3. TONE/PULSE SWITCH is in the right position. 4. TELEPHONE LINE CORD is plugged into the telephone jack. Range of phone limited, check the following: 1. ANTENNA on BASE UNIT is raised. 2. BASE UNIT is centrally located in your residence.
Rake MH oe FCC ID: NS2MH9003 Problem Solving he LX Excess static, check the following: 1. Check to see that the ANTENNA is not touching Raised the ANTENNA. another metal object. If after pressing the TALK button, you receive three beeps and no dial tone, check the following: 1. BASE UNIT is plugged into goer source. NOTE: If no telephones in the house are working, disconnect one set at a time to verify that none of the phones are causing the problem.
Oe dle Erie Technical Information | ‘ 4 This cordless telephone uses radio frequencies to allow mobility. There are certain +: difficulties in using radio frequencies with a cordless telephone. While these are normal, the following could affect the operation of your system. Noise Electrical pulse noise is present in most homes at one time or another. This noise is most intense during electrical storms.
FCC ID: NSZMH9003 TEE i ol FCC Requirements Federal Communications Commission Requirements This equipment complies With Part 68 of FCC Rules. A label on the BASE UNIT of this equipment contains, among other information, the FCC Registration Number and the Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.
FCC Requirements Federal Communications Commission Requirements (continued) Note: This equipment has been tested and found to comply with the limits for a class’ B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC ID: NS2MHS003 Warranty Information Bell South Products One-Year Limited Warranty This limited warranty sets forth all Bell South Products responsibilities regarding your product. There are no other expressed or implied warranties from Bell South Products. Warranty Service Provided If you purchased the new telephone from a retail vendor, Bell South Products warrants the telephone against defects in material and workmanship for a period of one (1) year from the original date of purchase.
| TE HE Ray ARE = Rif part) | Bon 0 What to Do for Warranty Service During the first thirty (30) days, a defective product is eligible for over-the-counter exchange at the retailer from whom it was purchased. After thirty (30) days, the defective product should be returned to the authorized service center. Please allow 2.3 weeks for the return of your telephone product. The shipping address of the authorized service center is: ~ © U.S. Electronics Service Center \ 105 Madison Avenue ’ New York, NY 10016 NOT
i. Cia Franti palo ed Ln FTE ATP LAE : re 3, Geti VITAE .
FCC ID: NS2MH9003 wi MHI00p22 pm "1. Cutout this page. This page serves as a template for attachment of screws to the wall when mounting this telephone on the wall. » "2. Use this template to determine the distance between screws when mounting this phone on the wall. The two cross hairs identify where to attach the Screws.
IMPORTANT In order to get maximum life { om the HANDSET battery pack, be sure to charge the HANDSET for 12 hours before initial use. IMPORTANT Placing your BASE UNIT near appliances such as televisions, refrigerators, radians, or microwave ovens may cause interference. IMPORTANT When you hear interfere se. press ttys CH button to change the operating channel. 5 IMPORTANT The AC ADAPTER must always be plugged into an electrical outlet.
Make certain you receive the best performance from your telephone. Read this manual first.