DotSurfer 6210 USER Manual 2002 GTRAN Wireless Inc. All rights reserved. No reproduction in whole or in part is permitted, without prior written approval. GTRAN Wireless Inc. and DotSurfer are registered trademarks of GTRAN Wireless Inc. The information in this user manual is subject to change without notice and does not represent a commitment on the part of GTRAN Wireless, Inc. Model Number: GPC-6210 Version 1.
GTRAN Wireless Inc. TABLE of CONTENS 1. DOTSURFER 6210 INTRODUCTION ................................... 3 2. LAPTOP.................................................................................... 4 2.1 INSTALLATION .................................................................................................................................4 2.2 UNINSTALLING THE DOTSURFER DRIVER AND PROGRAM......................................................8 2.3 USING GT DIALER III ........................
GTRAN Wireless Inc. 1. DOTSURFER 6210 INTRODUCTION GTRAN Wireless DotSurfer 6210 is a high-speed wireless Type II PCMCIA modem card that fits into major laptops, PDAs, and other mobile devices that utilize MS Windows Operating Systems and a PCMCIA Type II expansion slot. Allowing for wireless Internet connectivity under CDMA 1xEV-DO network, DotSurfer modem card delivers unmatched speed at up to 2.4 Mbps.
GTRAN Wireless Inc. 2. IBM ThinkPad I-Series 1661 WINDOW ME 2.1 INSTALLATION Step 1: Software Installation You must install the software from the CD before inserting the DotSurfer modem card! a. Make sure that the DotSurfer card is not inserted into the PCMCIA slot. b. Close all the other programs that are running before starting the application. Insert the installation software CD into your CD-ROM drive. The InstallShield Wizard should run automatically. If it does not, click Start-> Run and enter d:\Setup
GTRAN Wireless Inc. a. When PCMCIA Card is inserted, the window of the Add New Hardware Wizard is popped up. Click the “Next” button on the window. b. To find the driver file, select the item as the same as below on the window. Then, click the “Next” button on the window. c. When the window as below is popped up, it is ready to find the driver for your PCMCIA Card. Select the item as the same as below on the window. Then, click the “Next” button on the window.
GTRAN Wireless Inc. d. When the driver file has been found from the authorized path, click the “Next” button on the window. e. The window below is popped up because there is none of Digital Signature from Microsoft in your laptop. It is safe, so just click Yes button on the window. Then, installation will be continued.
GTRAN Wireless Inc. f. Click “Finish” button on the window to complete the installation.
GTRAN Wireless Inc. 2.2 UNINSTALLING THE DOTSURFER DRIVER AND PROGRAM a. Go to Settings -> Control Panel -> System. b. Select the Hardware -> Device Manager tab. c. Select Modem -> GTRAN DotSurfer 1xEV-DO Wireless Modem. d. Click GTRAN DotSurfer... modem with the right button of mouse. Then, select remove on the pop-up menu. It will remove the PCMCIA card from your laptop. e. Go back to Control Panel -> Add/Remove Programs. f.
GTRAN Wireless Inc. 2.3 USING GT DIALER III Main screen shown below will appear once GT Dialer III starts running. Read SMS Write SMS Sent Connect/ Disconnect Address Book Connected to network No/new message Signal Roaming strength on/off 2.3.
GTRAN Wireless Inc. 2.3.2 Connecting to Network a. On the main GT Dialer III, go to Setting and input required information under User Defined and DNS Setting. Click OK when finished. b. Click Connect from the GT Dialer III.
GTRAN Wireless Inc. 2.3.3 Setting From the main screen, click “Setting” button. Screen shown below will appear. Reset - Connection Times This Month: Accumulated usage time for this month. Last Month: Accumulated usage time for last month. Total: Accumulated time of usage before resetting. - Accumulated Data Volume Out: Transferred packet size since network is connected till disconnected. In: Received packet size since network is connected till disconnected.
GTRAN Wireless Inc.
GTRAN Wireless Inc. 2.4 SMS 2.4.1 Read SMS From the main screen, click SMS Read icon, Receive SMS screen will appear. < Reference > - Can save up to 30 SMS messages New Message Read Message . To continue to read other messages, select them by clicking . “Delete” Deletes the message . “Delete All” Deletes all read message . “Reply” Replies to sender . “Refresh” To read new message, while you read message .
GTRAN Wireless Inc. 2.4.2 Write SMS a. From the main screen, click “Write Messages” icon. Write Message screen will appear. b. Input receiver’s phone number and text. c. Once finished inputting, click one of the three buttons: Send, Send & Save, or Save. Sends new message without saving in Sent box. Sends new message and saves in Sent box. Saves new message in Sent box without sending. d. “Back” Goes back to main page.
GTRAN Wireless Inc. 2.4.3 Send SMS (Sent Box) Click “Sent SMS” button from the main screen.
GTRAN Wireless Inc. 2.4 4 Address Book Management On the main screen, click “Address Book” icon and Address book screen will appear as shown below. Previous Address Next Address < Reference > - Can save up to 100 addresses Search and Read Address Book a. Click icon to find an address by index number. b. You may search by name, by phone number, by e-mail, or by index number. Input the information and click c. icon. Search by phone number, input a phone number and click d.
GTRAN Wireless Inc. Add to Address Book a. From Address Book screen, Click “New”. b. Input name, home number, office number, mobile number, and e-mail address. Click “Save” and the inputted data will be stored. Edit Address Book a. Select the address to edit and update information. b. When editing is finished, click “Save”. Delete from Address Book Select the address to delete and click ”Delete” Other a. Click “List” to see all the list of addresses. b.
GTRAN Wireless Inc. 3. COMPAQ IPAQ 3870 WINDOWS PPC2002 3.1 INSTALLATION In addition to your iPAQ, you need the following: - USB cradle - Desktop or laptop PC - PC card expansion pack - Microsoft ActiveSync 3.1 or higher Note: Do NOT insert the DotSurfer modem card in your iPAQ until the software is installed. a. Make sure that the DotSurfer card is not inserted into the PCMCIA slot. b. Synchronize your iPAQ and computer by inserting the Microsoft ActiveSync 3.1 CD into your computer.
GTRAN Wireless Inc. h. When the installation is complete, the screen will appear as shown below. Click OK and the installation will automatically run in your iPAQ PDA. i. When the synchronization is complete, take the iPAQ out of the cradle. Attach the PC card expansion pack to the PDA and insert the DotSurfer modem card into the PC card slot. j. Using iPAQ's stylus, press the reset button on the right bottom of the PDA.
GTRAN Wireless Inc. 3.2 USING GT DIALER3 3.2.1 Network Connection a. Go to Start -> Programs -> Connections ->1XEvDo. b. When you see the screen below, input user ID, password, etc. and click Connect” c. Once connected, go to Start –> Internet Explorer and start surfing the web.
GTRAN Wireless Inc. d. After the initial connection setting is complete, you can connect to network as the following: Go to Start->GTDialer3 as below window. You can find out the status of 1xEV-DO on today.
GTRAN Wireless Inc. GT Dialer3 3.2.
GTRAN Wireless Inc. 3.2.3 Internet Connect/Disconnect Click “Connect/Disconnect” button as below. < Before connection > < After connection > 3.2.4 SMS Write SMS a. Click ”Write SMS” button of GT Dialer3 main screen. b. Input a number & message and click “Send”. Message will send.
GTRAN Wireless Inc. c. If you click “Clear all” button, message will be delete all. Read SMS a. Click “Read SMS” button, to read message from GTDialer3. b. To reply to the received message, select the message and with the Stylus, tap and Hold. Select “Reply” from the pop-up menu.
GTRAN Wireless Inc. c. To forward a message to others, using the stylus, tap and hold. Select “Forward” from menu. d. To delete a message, select the message. Using the stylus, tap and hold, which will display the pop-up menu. Select “Delete” from the pop-up menu. e. To delete all messages, click “Delete all” button. f. To check SMS by manually, click “Refresh” button. Sent SMS a. Click “SMS Sent” button from GTDialer3 main screen.
GTRAN Wireless Inc. b. To check a new SMS by manually, click “Refresh” button. c. To delete all messages, click “Delete all” button. d. To re-send the message, click “Re-send” button from pop-up menu. a. To delete an SMS message, select the message. Using the Stylus, tap and hold, which will display the pop-up menu. Select “Delete” from the pop-up menu. 3.2.5 Phone Book a. Click “Phone Book” tab from main GTDialer3 screen. Will appear a screen as a below. b.
GTRAN Wireless Inc. c. To search fro the phone number or string from your contact list, click “Search” button. Enter a number or string and click “OK” button. d. To delete the entire list, click the “Delete All” button. e. To useful each menu, use Tab-and-hold in menu.
GTRAN Wireless Inc. Send E-Mail: E-mail sending Edit: To edit a contact from the list Delete: To delete a contact from the list 3.2.6 Other Displays a. From GT Dialer3 main screen, click “Tool->Information” button. Total used : Total time used prior to resetting the accumulated time. This Month : Accumulated time for this month. Last Month : Accumulated time for last month.
GTRAN Wireless Inc. - Go to “Tool ->Information ->Transfer Packets” Card displays the transfer packets. A packet size defines to 512 bytes. OUT: IN: Received packets during connection. Sent packets during connection. b. From GT Dialer3 main screen, click “Tool->Setting” button, You’ll see two options on the pop-up menu: Message and Sound.
GTRAN Wireless Inc. - To select a method of receiving, go to “Tool-> Setting -> Message” If inbox is full, select Rejected new msg and select Deleted the oldest & stored new msg. - To select a sound of SMS notice “Tool -> Setting -> Sound” : Select a wav file that you want and click “OK” button.
GTRAN Wireless Inc.
GTRAN Wireless Inc. APPENDIX A: PRODUCT SPECIFICATIONS SYSTEM REQUIREMENTS Card Slot 1 Type II PCMCIA Processor P133 or higher Disk Space 20 MB RAM 64 MB Disk Drive CD-ROM Drive Internet MS Internet Explorer 4.0 or higher Windows 98 and 98SE Operating System Windows ME Windows 2000 Windows XP Windows CE 3.
GTRAN Wireless Inc. APPENDIX B: SAFETY AND REGULATORY INFORMATION SAFETY AND HAZARDS The DotSurfer modem card should not be used in locations where the use of radio frequency equipment is restricted or prohibited. DotSurfer can transmit signals that could interfere with various systems in aircraft, medical equipments, and life support equipments. Please do not use the DotSurfer modem card in these restricted locations.
GTRAN Wireless Inc.