User's Manual

ManualsBrandsGTO Access Systems ManualsElectronicsWireless keypad control

CSKPL

DIGITAL KEYPAD

TRANSMITTER

Installation Instructions

DESCRIPTION

This Digital Keypad is designed for use with automatic garage door

operators. The radio format provides unparalleled security with more than

a million different codes.

To activate the door operator, the user enters their unique 1 to 6 digit long

code on the unit’s keypad and presses the START/STOP button. For up to 30

seconds after the last activation, the keypad can be re-triggered by simply

pressing the START/STOP button again. This allows the user to stop or

reverse the opener quickly, without having to re-enter their code.

The keypad has built-in lighting for use at night or in dark areas. The clear

silicone keys are backlit with a pleasing blue glow. By pressing the START/

STOP button rst, before entering their code, the user can light up the

keypad. Pressing the START/STOP button twice at any time will light up

the keypad.

The keypad lockout timer will disable the keypad after 10 activations. The

keypad must remain idle for 30 seconds before new attempts.

The garage door operator contains a built-in receiver that is programmed by

sending a signal from the user’s transmitters. This stores the transmitter’s

code into the receiver’s memory. The receiver will retain its memory even

without power and will only activate from these “memorized” transmitters.

Each keypad code can be considered a different transmitter.

KEYPAD COMPONENTS KEYPAD FEATURES

KEYPAD OPERATION CHANGING BATTERIES LIMITED WARRANTY FCC STATEMENT

PROGRAMMING OPERATOR WALL MOUNTING

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,MDTK,PVT LBL - GTO P/N: 10007727 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1

www.mightymule.com

ADDING A KEYPAD CODE

PRESS THE OPERATOR'S LEARN

BUTTON FOR 1 SECOND AND RELEASE.

THE OPERATOR SHOULD BEEP AND THE

LIGHT SHOULD BLINK ONCE.

THE RED LED WILL REMAIN LIT (LEARN

REMOTE MODE).

WHILE THE RED LED IS ON,

ENTER A 1-6 DIGIT KEYPAD CODE

THEN PRESS AND HOLD THE KEYPAD'S

START/STOP KEY UNTIL THE OPERATOR

BEEPS AND THE LIGHT BLINKS ONCE.

REPEAT STEPS 1 & 2 FOR ANY

ADDITIONAL KEYPAD CODES

SCREW

PLUGS

SCREW

ANCHORS

MOUNTING

SCREWS

KEYPAD

HINGED COVER

PROTECTS THE

KEYPAD

SOFT BLUE LIGHTS

ILLUMINATE THE KEYS

FOR NIGHTTIME USE

START/STOP BUTTON STAYS ACTIVE FOR

30 SECONDS AFTER A CODE IS USED SO THE

OPENER CAN BE STOPPED OR REVERSED

NOTE: FOR SECURITY, THE KEYPAD WILL SHUTDOWN

AFTER 10 CODE ENTRIES UNTIL IT IS IDLE FOR 30 SECONDS

TEN KEYS ENTERING

1-6 KEYPAD CODES

USING NUMBERS OR LETTERS

MOUNT THE KEYPAD IN

CLEAR VIEW OF THE DOOR

WITH THE TWO SCREWS SUPPLIED

USE THE SCREWS

ANCHORS SUPPLIED

IF REQUIRED

SCREWS

ANCHORS

PUSH IN THE

TWO SCREW

COVER TO HIDE

THE SCREWS

DAYTIME OPERATION

START

STOP

START

STOP

START

STOP

PRESS START/STOP (LIGHTS KEYPAD)

NIGHTTIME OPERATION

PRESS THE LIGHT ( ) BUTTON TO TURN THE OPERATOR’S LIGHT ON/OFF

(KEYPAD MUST HAVE AT LEAST ONE CODE PROGRAMMED INTO THE OPERATOR)

LIGHT OPERATION

1-6 DIGIT KEYPAD CODE THAT

WAS ENTERED INTO OPENER

ENTER THE KEYPAD CODE

PRESS START/STOP

ENTER THE KEYPAD CODE

PRESS START/STOP

1-6 DIGIT KEYPAD CODE THAT

WAS ENTERED INTO OPENER

NOTE: TO STOP OR REVERSE THE OPERATOR, THE START/STOP BUTTON CAN BE

PRESSED AGAIN FOR UP TO 30 SECONDS WITHOUT RE-ENTERING THE CODE.

REMOVE THE TWO

SCREWS AND SLIDE

THE BATTERY COVER OFF

REMOVE THE

LOW VOLTAGE

BATTERIES AND

DISPOSE OF THEM

PROPERLY

INSTALL 3 FRESH

AAA BATERIES

BE SURE THE

SILICONE GASKET

IS IN PLACE

REPLACE THE

BATTERY COVER

AND RE-INSTALL

THE TWO SCREWS

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-

sonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION!

Any changes or modications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

This product is warranted to the original consumer against defects in material and workmanship

for the periods mentioned above. GTO Access Systems will repair, or at its option, replace, any

device that it nds requires service under this warranty. This warranty does not apply to damage

to the product from negligence, abuse, abnormal usage, misuse, accidents, normal wear or tear

or due to failure to follow Seller’s instructions, or arising from improper installation, storage or

maintenance. In no event will GTO Access Systems be responsible for incidental, compensatory,

punitive, consequential, indirect, special or other damages. The remedies provided by this

warranty are exclusive. Some states do not allow the exclusion or limitation of incidental

and consequential damages, so the above limitation or exclusion may not apply to you. Any

warranties implied by law are limited to the time periods set forth above. Some states do not

allow limitations on how long an implied warranty lasts, so the above limitation may not apply

to you. This warranty gives you specic legal rights, and you may also have other rights which

vary from state to state.

For warranty service, contact GTO Access Systems at 800-543-1236. In order to be protected by

this warranty, save your proof of purchase should repair be required.

IMPORTANT!

Radio controls provide a reliable communications link and ll an important need in portable

wireless signaling. However, there are some limitations which must be observed.

• For U.S. installations only: The radios are required to comply with FCC Rules and

Regulations as Part 15 devices. As such, they have limited transmitter power and therefore

limited range.

• A receiver cannot respond to more than one transmitted signal at a time and may be

blocked by radio signals that occur on or near their operating frequencies.

• Changes or modications to the device may void FCC compliance.

• Infrequently used radio links should be tested regularly to protect against undetected

interference or fault.

• A general knowledge of radio and its vagaries should be gained prior to acting as a

wholesale distributor or dealer, and these facts should be communicated to the ultimate

users.