GT-Sense SMA Connectors Installation Guide CM2-1112120 Rev.
Electrical Ratings and Requirements Product Supply Ratings Power Supply: 18-36 VAC 50-60 Hz or 12-36 VDC, 2A WARNING ! These procedures should only be performed by trained installation technicians. High voltage/current lines are present and caution should be used to prevent injuries. Installer must conform to local standards and ordinances as required. IMPORTANT! During the installation a hole is to be drilled in the controller door.
Required Tool Kit • 13mm (1/2 ") Drill Bit • Center Punch • Cutting compound for the drill • Drill for removing burrs • Degreasing rags • Screwdrivers: T20 Torx and Philips • 18mm open face wrench • SMA Connector Wrench (GT PN TOL0005) • Side cutting pliers • Magnet • Cable Ties Globe Tracker Installation Guide · Carrier NaturaLINE, PrimeLINE, ThinLINE & EliteLINE 3
GT Sense Reefer Kit A complete GT Sense Reefer Kit includes: 1. GT Sense Device 2. RMM Bracket Kit 3. Antenna (80 mm diameter round black version with 3M VHB tape and threaded mount on the back cables and connectors 4. RMM Cable PN CBL0020 5. Activation magnet 1. Globe Tracker 2. 3. Installation Guide · Carrier NaturaLINE, PrimeLINE, ThinLINE & EliteLINE 4. 5.
If the GT Sense Device is already attached to the RMM Bracket proceed to step 1. If it is not already attached to the RMM Bracket see below: Remove the white protective coating from both sides of the RMM Bracket (if present) and attached the RMM Bracket to the back of the GT Sense Device using the 4x flat head thread-forming. Start all 4 screws through the countersunk holes and into the holes in the GT Sense Device enclosure with a T20 torx bit before tightening the screws to 6 kg-cm (5 in-lbs).
Before beginning the antenna installation, please print and cut out the template that can be found at the end of this document. Step 1 Use the antenna installation template to locate the antenna placement on the door. Hinge Place the template towards the edge of the door on the hinge side and mark the center point. The center point should be 10 cm from the edge of the door on the hinge side.
10 cm 10 cm PrimeLINE and ThinkLINE: NatureLINE and EliteLINE: Antenna installed on right side of the door. Antenna installed on left side of the door.
Step 3 Degrease/clean the surface where the antenna will be mounted with a metal cleaner or similar before fitting the antenna. Step 4 Remove the nut, lock washer, and plastic washer from the threaded mount on the backside of the antenna by slipping them off the antenna cable via the slots. Step 5 Insert the connector end of the antenna cable through the dirlled hole in the door. Remove the 3M VHB table liner from the backside of the antenna.
Step 7 If a modem is already present in the RMM slot, remove it maintaining the mounting screws and unplug all of the connections. Step 8 Route the antenna cables across the door hinge through existing cable channel (if present) to the RMM slot using the cable ties to secure the cables. Do not be concerned with the extra length of cable at this time.
Step 11 Fit the GT Sense Device into the RMM slot and secure with the screws from the removed modem. If no modem was removed, use the M5 screws and mylar washers provide in the RMM bracket kit. Step 12 Connect the 7 position RS232 terminal block connector and the 3 position power terminal block connector to the mating connector from the reefer controller. Check to be sure the screw terminals on all connectors are on the same side of the mated connectors.
Antenna Installation Templates 100 mm 80 mm 80 mm 100 mm Cut out the template above and use it to locate the position of the antenna mounting hole. NOTE: Print in 100% Use a center punch to pm the dot at the center of circle to locate the mounting hole.
GT-Sense SMA Connectors Model: CM2-1112120 FCC ID:2ASJR-CM2-1112120 FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF exposure statement: The equipment complies with FCC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. CE Warning This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user’s body and the handset, including the antenna.