INSTRUCTION MANUAL R2 FLX CAMERA MODEL: STC-XV4WF
**IMPORTANT NOTE** To ensure the product is being utilized to its full potential, we recommend checking our website for new product updates. If your unit is having trouble, please check the website to determine you are using the latest firmware or software version. TECHNICAL SUPPORT EMAIL: Stealthcam@gsmorg.com Please allow 48 hours for email response. STEALTH CAM P.O. Box 535189 Grand Prairie, TX 75053-‐9504 www.
TABLE OF CONTENTS Camera Overview General Information / Specifications Switch / Button Functions On-Screen Display Functions & Features Camera Settings Wireless Setup Wireless Settings Memory Card Installation Formatting Battery Removal & Installation Definitions Frequently Asked Questions (FAQs) FCC Compliance Limited Warranty Information www.stealthcam.
CAMERA OVERVIEW (NOTE: You’ll need to screw the supplied antenna into the top of the camera.) NOTE: You will find your Serial # under the weather seal gasket toward the bottom of the camera. www.stealthcam.
CAMERA OVERVIEW (cont.) Battery Compartment (8‘AA’ Batteries) www.stealthcam.
GENERAL INFORMATION ! ! ! ! ! ! ! ! ! ! Operating Environment: 14 to 104 deg F (-10 to 40 deg C). 20-85% relative humidity, non-condensing. The camera is designed to be weather resistant. Never attempt to immerse the unit in water or any other liquid. This will damage the unit and void the warranty. Do not mix old and new batteries. Do not mix alkaline, standard, or rechargeable batteries. Use a soft lens cloth for cleaning lens.
SWITCH / BUTTON FUNCTIONS 3 Position Switch ! ! ! OFF position: The unit will be OFF when the switch is in this position. ON position: The unit is now ON, defaults to Qset1 on first power up. After each time the camera is turned ON, the unit will remember the previous mode and settings. TEST position: This position is to test the PIR sensor.
ON-‐SCREEN DISPLAY ICONS Quick Sets (QSET) While in any Quick Set Mode, the LCD screen will display the Qset that the camera is currently set to in the top left corner. The bottom half of the screen will give a digital read out of how the camera is preprogrammed. It will scroll across the display like below: PHOTO...8.0MP...30 S DELAY...
FUNCTIONS & FEATURES Quick Sets (QSET) ! QSET 1 The unit will be set to the following settings: o o o o o o Operational Mode: PIR Photo Photo Resolution: 8.0 MP PIR Delay: 30 seconds Burst Mode: 3 Photos Reduce Blur: ADVANCED Info Bar: ON Scrolling Text PHOTO...8.0MP...30 S DELAY...3 PHOTO BURST ! QSET 2 The unit will be set to the following settings: o o o o o o Operational Mode: PIR Photo Photo Resolution: 8.
CAMERA SETUP Setup Date: Set the Date for the camera. ! The default date is 01/01/19 Setup Time: Set the Time for the camera. ! The default time is 12:00AM Time Zone: Set the Time Zone where you’re using the camera. ! Eastern ! Central (Default) ! Mountain ! Pacific ! Alaskan ! Hawaiian Time Format: Set whether the time will be kept using a 12 Hour format or 24 Hour format.
CAMERA SETUP (cont.) ! Time Lapse: Camera takes a still image per preset time. o Time Lapse Settings are: Photo Resolution, PIR Delay, Time Lapse Delay, Time Lapse Start, Time Lapse Stop, Blur Reduction, Camera Name, Temperature, Information Bar, Latitude, Longitude, Factory Reset, Security Key, Format SD Card, Software Upgrade. o Time Lapse Photos will be marked with “TL” in the Information Bar.
CAMERA SETUP (cont.) Operating Hours (Default – 24/7): This setting tells the camera what specific hours to operate “scheduled” or to “always” be on. o 24/7 o Scheduled ! Start (Default - 08:00AM) o Time ranges from 00:00 to 23:59 [HH:MM] ! End (Default - 05:00PM) o Time ranges from 00:00 to 23:59 [HH:MM] NOTE: Activity Start/End settings are visible only if Scheduled is selected ! ! Photo Resolution (Default – 8.
CAMERA SETUP (cont.) ! Reduce Blur (Default – Advanced) o PROGRESSIVE – This setting will use a maximum exposure time of 1/125sec for the night photos. Other adjustments are made to increase the brightness and clarity of the photo. o ADVANCED – This setting will use a maximum exposure time of 1/40sec for the night photos. o STANDARD – This setting will use a maximum exposure time of 1/15sec for the night photos.
CAMERA SETUP (cont.) Options only if in Time Lapse Mode. ! Time Lapse Delay – to set the delay between photos. o Will display as “TL DELAY” in Camera Setup. o The camera will take PIR photos during the Time Lapse Session when the Time Lapse Delay is set to 60 seconds or greater. o The Time Lapse range is from 5 seconds to 59 minutes and 59 seconds. o The default Time Lapse Setting is 30 seconds.
CAMERA SETUP (cont.) Options only if in Video Mode. ! Video Resolution (Default – 1280x720) o 1920 x 1080 o 1280 x 720 NOTE: If Wireless Modem is set to ON, then the PIR Video mode has special settings. ! 320x176 ! Video Length (Default - 10 sec) o Set the video length from 10 to 180 seconds in 5-second increments. o Motion Active Video (MAV) - This is a dynamic video length setting monitoring the PIR triggers.
CAMERA SETUP (cont.) ! Temperature (Default – Fahrenheit) o The temperature is imprinted on each photo in either Celsius or Fahrenheit. ! Information Bar (Default – ON) o The Stealth Cam logo, Time, Date, Temperature Moon Phase, and Camera Name are imprinted on the bottom of each picture.
CAMERA SETUP (cont.) The icons for the moon phase are as follows (see Symbol): www.stealthcam.
CAMERA SETUP (cont.) ! Latitude: This function will allow the user to manually set the latitude coordinates for the camera. o The default coordinates will be 000.000000 N, this number can be set to 000.000000 -‐ 179.999999 N or S. ! Longitude: This function will allow the user to manually set the longitude coordinates for the camera. o The default coordinates will be 000.000000 E, this number can be set to 000.000000 -‐ 179.
WIRELESS SETUP The camera has the ability to communicate with Bluetooth enabled mobile devices and wireless routers. To set this up the Stealth Cam Remote APP is required. Stealth Cam Remote App for iOS and Android are available for free on the iApple APP Store and Google Play Store. IMPORTANT: You must download the Stealth Cam Remote APP and Setup an Account prior to moving forward with the following wireless setup.
WIRELESS SETUP (cont.) ! FIELD • • • • ! Ensure Mobile Device Bluetooth is turn ON. Go to the Mobile Device Wi-Fi Settings and join the Camera's Wi-Fi Router (FLX Camera_XXXXX), then return to the Stealth Cam Remote APP and the Camera will automatically be detected. Click Continue to proceed to the next step. Create a Password (optional) - If you plan on connecting multiple devices to this camera you will need to setup a password to your Camera's Wi-Fi Router.
WIRELESS SETTINGS ! ! ! ! ! ! Wireless Setup: The Wireless Setup enables the binding of FIELD or LOCAL NETWORK mode. Select Start to begin. Wireless Mode: This screen shows the mode in which the camera is currently configured (FIELD or LOCAL NETWORK). This screen in not editable, to change the modes the Wireless Setup must be used. App Account (LOCAL NETWORK Only): The camera will display the current APP Account User Name.
WIRELESS SETTINGS (cont.) ! Upload Time (LOCAL NETWORK Only): This time determines when the camera uploads any new photos or videos to the APP. For example, if the Upload Time is 3:30pm and the camera is set to Twice per day, then the camera will transmit photos at 3:30pm and 3:30am every day. ! Date & Time Sync: This setting allows the camera to automatically set the Date and Time.
Using Your Camera in FIELD mode ! FIELD • • • • • Bring Mobile device with the APP open within Bluetooth Range (50 feet) of the Stealth Cam FLX Camera. (Mobile device Bluetooth must be turned on) Once the Stealth Cam Camera is in range, the in range cameras go from gray to color on the camera screen within the APP and it also shows the BT Signal Strength. Once selected the camera will automatically aturn on its on board Wi-Fi Router. Your mobile device will automatically connect to the Wi-Fi Router.
MEMORY CARD INSTALLATION To insert the SD memory card into the camera: first locate the SD card slot on the right hand side of the of the camera case. Next with the SD card label facing towards the front of the camera, insert the SD card. When the card has been pressed in fully there will be a noticeable resistance as the spring locking mechanism activates to hold on the SD card.
FORMATTING SD CARD It always best to format your SD cards from the actual device you are using, in this case the camera. This will allow the camera to format the card in the proper fashion. 1. Insert SD card into the camera. 2. Turn the camera power ON. 3. Press the MENU button. 4. Navigate to “Camera Settings”. Press ENTER. 5. Navigate to "Format Card". Press ENTER. 6. Navigate to "Yes". Press ENTER. 7.
BATTERY REMOVAL & INSTALLATION To remove the batteries from the unit; open the case and press the EJECT button on the lower right hand corner. This will cause the battery tray to be released and slide downwards. New, Alkaline or Lithium, ‘AA’ batteries must be inserted with the orientation as shown on the tray.
DEFINITIONS REFLEX (Sub 1-Second Trigger) – Ultra-fast trigger speed. Never miss a crucial moment. MATRIX (Blur Reduction Technology) – Advanced blur reduction dramatically reduces blur effects resulting in sharper, clearer images. RETINA (Advanced Low-Light Sensitivity) – Superior low light performance for extended nighttime range. MULTI-ZONE DETECTION - Provides for more accurate coverage at angle and distance.
FREQUENTLY ASKED QUESTIONS (FAQs) Q: What could cause my wireless setup to fail? A: Your wireless setup can fail for the following reasons: • Camera has low or dead batteries.
FREQUENTLY ASKED QUESTIONS (cont) Q: Can viewing photos on my hand held digital camera cause my trail camera to malfunction? A: Yes, we recommend viewing your photos/videos on a computer as other digital devices can change the format of the SD card. Q: Can I swap SD cards from one scouting camera to another? A: No, We do not recommend swapping SD cards between different cameras.
FCC COMPLIANCE GSM STC-XV4WF This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
LIMITED WARRANTY INFORMATION Your Stealth Cam scouting camera is covered by a 365 Day Limited Warranty on parts and labor from the date of original purchase, and purchases must be made through an authorized dealer. The warranty covers defects in workmanship and materials. The warranty does not apply to units, which have been damaged or abused intentionally or unintentionally.
MANUEL D'INSTRUCTIONS FLX CAMERA MODÈLE : STC-XV4WF www.stealthcam.com 877-‐269-‐8490 V.
**NOTE IMPORTANTE** Pour vous assurer que le produit soit utilisé à son plein potentiel, nous vous recommandons de vérifier notre site Web pour obtenir les nouvelles mises à jour du produit. Si votre appareil a des problèmes, veuillez consulter le site pour déterminer si vous utilisez le dernier Minilogiciel ou la toute dernière version du logiciel. SOUTIEN TECHNIQUE COURRIEL : stealthcam@gsmorg.
TABLE DES MATIÈRES APERÇU DE L'APPAREIL PHOTO INFORMATIONS GÉNÉRALES / CARACTÉRISTIQUES SWITCH / FONCTIONS DES BOUTONS À L'ÉCRAN Icônes d'Affichage FONCTIONS ET CARACTÉRISTIQUES CONFIGURATION DE LA CAMERA CONFIGURATION SANS FILS PARAMÈTRES SANS FIL CARTE MÉMOIRE INSTALLATION FOMATAGE DE LA CARTE SD INSTALLATION ET RETRAIT DE LA PILE DÉFINITIONS FOIRE AUX QUESTIONS (FAQ) CONFORMITÉ FCC RENSEIGNEMENTS SUR LA GARANTIE LIMITÉE www.stealthcam.
APERÇU DE L'APPAREIL PHOTO NOTE: Vous trouverez votre N ° de série sous le joint d'étanchéité de la météo vers le bas de la caméra. www.stealthcam.
APERÇU DE L'APPAREIL PHOTO (SUITE) Arrière www.stealthcam.
INFORMATIONS GÉNÉRALES ! ! ! ! ! ! ! ! ! ! ! Environnement de fonctionnement: de 14 à 104 ° F (X 10 à 40 ° C). Humidité relative de 20 à 85%, sans condensation. instructions de soins spéciaux !! L'appareil photo est conçu pour être résistant aux intempéries. Ne essayez jamais d'immerger l'unité dans l'eau ou tout autre liquide. Cela pourrait endommager l'appareil et annuler la garantie. Ne pas mélanger piles neuves et anciennes.
SWITCH / FONCTIONS DES BOUTONS 3 Interrupteur de position ! ! ! Position OFF: L'appareil sera éteint lorsque l'interrupteur est dans cette position. Position ON: L'unité est maintenant activée, par défaut à Qset1 lors de la première mise sous tension. Après chaque mise sous tension de l'appareil photo, l'appareil mémorise le mode et les réglages précédents. Position TEST: Cette position sert à tester le capteur PIR.
À L'ÉCRAN ICôNES D'AFFICHAGE Ensembles rapides (QSET) En mode Quick Set, l'écran LCD affiche le Qset sur lequel la caméra est actuellement réglée dans le coin supérieur gauche. La moitié inférieure de l'écran donnera une lecture numérique de la façon dont l'appareil photo est préprogrammé. Il fera défiler l'affichage comme ci-dessous: PHOTO ... 8.0MP ... 30 S Délais ...
FONCTIONS ET CARACTÉRISTIQUES ! QSet 1 L'unité sera réglé sur les paramètres suivants: o Mode opérationnel: PIR photo o Résolution photo: 8,0 MP o PIR Délai: 30 secondes o Mode rafale: 3 Photos o Réduire le flou: ADVANCED o Info Bar: ON ! QSet 2 L'unité sera réglé sur les paramètres suivants: o Mode opérationnel: PIR photo o Résolution photo: 8,0 MP o PIR Délai: 30 secondes o Mode rafale: 1Photo o Réduire le flou: ADVANCED o Info Bar: ON ! Q
CONFIGURATION DE LA CAMERA Si le bouton Menu est pressée alors que dans le mode de configuration de la caméra, la caméra passe en mode Auto. Date de configuration: Fixer la date de l'appareil photo. ! La date par défaut est 01/01/19 Time: Réglez le temps pour l'appareil photo. ! La durée par défaut est 00:00 Fuseau horaire: Définition du fuseau horaire où vous utilisez l'appareil photo.
CONFIGURATION DE LA CAMERA (suite.) Time Lapse: L'appareil photo prend une image fixe par unité de temps prédéfini. o Time Settings Accéléré sont: Photo Résolution, PIR Delay, Accéléré Delay, Accéléré Démarrer, Accéléré Stop, Réduction du flou, Nom de la caméra, la température, la barre d'informations, Latitude, Longitude, Réinitialisation usine, la clé de sécurité, Format SD Card, Software Mettre à niveau.
CONFIGURATION DE LA CAMERA (suite.) ! Heures de fonctionnement (par défaut - 24/7): Ce paramètre indique la caméra ce que heure spécifique à fonctionner "prévue" ou "toujours" être sur.
CONFIGURATION DE LA CAMERA (suite.) ! ! Réduire le flou (par défaut - Advanced) o PROGRESSIVE - Ce réglage utilisera une durée d'exposition maximale de 1/125 secondes pour les photos de nuit. D'autres ajustements sont effectués pour augmenter la luminosité et la clarté de la photo. o AVANCÉ - Ce réglage utilisera une durée d'exposition maximale de 1/40 s pour les photos de nuit. o STANDARD - Ce réglage utilisera une durée d'exposition maximale de 1/15 seconde pour les photos de nuit.
CONFIGURATION DE LA CAMERA (suite.) En option seulement si en mode Time lapse. ! Accéléré Delay -‐ Pour définir le délai entre les photos. o Se affiche comme "DELAY TL» dans les réglages de l'appareil photo. o L'appareil photo attendre un certain laps de temps entre les photos Accéléré. o L'appareil photo prend des photos pendant la PIR Accéléré session lorsque le Accéléré délai est de 60 secondes ou plus.
CONFIGURATION DE LA CAMERA (suite.) En option seulement si en Vidéo Mode. ! Résolution de la vidéo (par défaut - 1280x720) o 1920 x 1080 o 1280 x 720 REMARQUE: Si Wireless Modem est réglé sur ON, le mode vidéo PIR comporte des paramètres spéciaux. ! 320x176 ! Durée de la vidéo (par défaut - 10 sec) o Régler la longueur de la vidéo de 10 à 180 secondes, par incréments de 5 secondes.
CONFIGURATION DE LA CAMERA (suite.) ! Température (par défaut -‐ Fahrenheit) o La température est imprimé sur chaque photo en degrés Celsius ou Fahrenheit. ! Barre d'informations (par défaut -‐ ON) o Le logo Stealth Cam, heure, date, Température Phase de Lune, et le nom de l'appareil photo sont imprimées sur le fond de chaque image.
CONFIGURATION DE LA CAMERA (suite.) Les icônes de la phase de lune sont les suivantes (voir Symbole): www.stealthcam.
CONFIGURATION DE LA CAMERA (suite.) Latitude: Cette fonction permet à l'utilisateur de régler manuellement les coordonnées de latitude pour la caméra. o Les coordonnées par défaut seront 000.000000 N, ce nombre peut être réglé sur 000.000000 -‐ 179.999999 N ou S. ! ! Longitude: Cette fonction permet à l'utilisateur de régler manuellement les coordonnées de longitude pour la caméra. o Les coordonnées par défaut seront 000.
CONFIGURATION SANS FILS La caméra peut communiquer avec des périphériques mobiles et des routeurs sans fil compatibles Bluetooth. Pour configurer cela, l'application Stealth Cam Remote est requise. L'application Stealth Cam Remote pour iOS et Android est disponible gratuitement sur l'App Store d'iApple et le Google Play Store. IMPORTANT: vous devez télécharger l'application Stealth Cam Remote et configurer un compte avant de poursuivre avec la configuration sans fil suivante.
CONFIGURATION SANS FIL (suite) ! ! FIELD • • Assurez-vous que Bluetooth du périphérique mobile est activé. Accédez aux paramètres Wi-Fi du périphérique mobile et rejoignez le routeur Wi-Fi de la caméra (FLX Camera_XXXXX), puis revenez à l'application Stealth Cam Remote et la caméra sera automatiquement détectée. Cliquez sur Continuer pour passer à l'étape suivante.
PARAMÈTRES SANS FIL ! ! ! ! ! ! Configuration sans fil: La configuration sans fil permet de lier le mode FIELD ou LOCAL NETWORK. Sélectionnez Démarrer pour commencer. Mode sans fil: Cet écran affiche le mode dans lequel la caméra est actuellement configurée (réseau ou réseau local). Cet écran n’est pas éditable, pour changer les modes, la configuration sans fil doit être utilisée. Compte app (réseau local uniquement): la caméra affiche le nom d'utilisateur du compte APP actuel.
PARAMÈTRES SANS FIL (suite) ! ! ! Heure de téléchargement (réseau local uniquement): Cette heure détermine le moment où l'appareil photo télécharge de nouvelles photos ou vidéos sur l'application. Par exemple, si l'heure de téléchargement est 15h30 et que l'appareil photo est réglé sur Deux fois par jour, il transmettra les photos à 15h30 et à 3h30 chaque jour. Synchronisation date et heure: Ce paramètre permet à l'appareil photo de régler automatiquement la date et l'heure.
Utilisation de votre appareil photo en mode FIELD ! FIELD • • • • • Amenez l'appareil mobile avec l'application ouverte dans la portée Bluetooth (50 pieds) de la caméra Stealth Cam FLX.(Le périphérique mobile Bluetooth doit être activé) Une fois que la caméra Stealth Cam est à portée, les caméras à proximité passent du gris à la couleur sur l'écran de la caméra dans l'application et affichent également l'intensité du signal BT.
CARTE MÉMOIRE INSTALLATION Pour insérer la carte mémoire SD dans l'appareil: localisez la fente de la carte SD sur le côté droit du boîtier de l'appareil photo. Ensuite, avec l'étiquette de la carte SD orientée vers l'avant de l'appareil photo, insérez la carte SD.
FOMATAGE DE LA CARTE SD Il est toujours mieux de formater vos cartes SD à partir de l'appareil actuel que vous utilisez, dans ce cas l'appareil photo. Ce qui permettra à l'appareil photo de formater la carte dans le mode approprié. 1. Insérez la carte SD dans l'appareil photo. 2. Mettez l'appareil photo. 3. Appuyez sur le bouton MENU. 4. Accédez à "Paramètres avancés". Appuyez sur ENTER. 5. Accédez à "Formater la carte".
INSTALLATION ET RETRAIT DE LA PILE Pour retirer les piles de l'appareil, ouvrez le boîtier et appuyez sur le bouton ÉJECTION situé dans le coin inférieur droit. Ce qui permettra de glisser et de retirer le Compartiment à piles. De nouvelles piles, alcalines ou au lithium, de type 'AA' doivent être insérées en respectant l'orientation indiquée sur le compartiment.
DÉFINITIONS REFLEX (Sensibilité avancée à faible luminosité) - Vitesse de déclenchement ultraP rapide. Ne manquez jamais un moment crucial. MATRIX(Technologie de réduction du flou) – Avancée réduction du flou réduit considérablement les effets de flou résultant en plus nettes, des images plus claires.
FOIRE AUX QUESTIONS (FAQ) Q: Qu'est-ce qui pourrait faire échouer ma configuration sans fil? A: Votre configuration sans fil peut échouer pour les raisons suivantes: • Les piles de l'appareil photo sont épuisées ou épuisées. • Mot de passe de routeur incorrect (réseau local) • Le routeur auquel vous essayez de vous connecter n’a pas d’accès Internet (réseau local).
FOIRE AUX QUESTIONS (SUITE) Q: La visualisation de photos sur mon appareil photo numérique portatif peut-elle provoquer un dysfonctionnement de mon appareil photo Trail A: Oui, nous vous recommandons d'afficher vos photos / vidéos sur un ordinateur, car d'autres appareils numériques peuvent modifier le format de la carte SD Q: Puis-je échanger des cartes SD d'un appareil photo à un autre? A: Non, nous ne recommandons pas de permuter les cartes SD entre différents appareils photo.
CONFORMITÉ FCC GSM STC-XV4WF Remarque : Cet équipement a été testé et se conforme aux exigences des appareils numériques de classe B, conformément à la partie 15 des Règles FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles présentes dans une installation résidentielle.
RENSEIGNEMENTS SUR LA GARANTIE LIMITÉE Votre appareil photo d'exploration Stealth Cam est couverte par une garantie limitée de 365 jours sur les pièces et la main-‐d'œuvre à partir de la date d'achat initial, et les achats doivent être effectués auprès d'un revendeur autorisé. La garantie couvre les défauts de fabrication et les matériaux.