3G Indoor Repeater GRS-1915D-SPR User Manual January, 2009 Version 0.
Sprint User Manual 3G Indoor Repeater - INDEX 1. SUMMARY................................................................................... 3 2. SYSTEM CONFIGURATION ......................................................... 5 2.1 3G Indoor Repeater Service Network Configuration ............... 5 2.2 System Design and Operation.................................................. 6 2.2.1 System Design........................................................................... 6 2.2.2 Downlink/Uplink Path ......
Sprint User Manual 3G Indoor Repeater 1. Summary GRS-1915D-SPR is a 3G Indoor repeater, which has been designed to improve signals in blanket/shadow areas inside of buildings to transmit Sprint signals at PCS 1900MHz band. Characteristics PCS Band: 72dB Gain with 15dBm maximum composite output power. Bandwidth: Entire PCS 1900 frequency A Block to F Block (45MHz). Bandwidth selection adjustable per user’s situation.
Sprint User Manual 3G Indoor Repeater Characteristics GRS-1915D-SPR repeater is an indoor repeater with output power of 15dBm. modules are classified as below: - DPX Filters to combine the input/output signals for: CDMA - Body (the whole module) - AC/DC Adapter - Controller to monitor each module in repeater.
Sprint User Manual 3G Indoor Repeater 2. System Configuration 2.1 3G Indoor Repeater Service Network Configuration
Sprint User Manual 3G Indoor Repeater 2.2 System Design and Operation 2.2.1 System Design
Sprint User Manual 3G Indoor Repeater
Sprint User Manual 3G Indoor Repeater Outside Port Design NO.
Sprint User Manual 3G Indoor Repeater 2.2.2 Downlink/ Uplink Path GRS-1915D-SPR improves and strengthens signals in PCS 1900MHz band. In downlink path, received from Donor Antenna signal is transferred through Duplexer (DPX) and Down Conversion (DNC) module, and after choosing one of 5MHz, 10MHz or 15MHz in IF path the signal is forwarded to Up Conversion (UPC) module. Then, improved signal is sent to Service Antenna through Diplexer (DPX). Uplink path is vice versa to Downlink path.
Sprint User Manual 3G Indoor Repeater 2.2.3 Frequency Selection A1 1930 A2 A3 1935 1940 D 1945 B1 1950 B2 1955 B3 1960 E 1965 F 1970 1975 MHz 1895 MHz Downlink Frequency Table A1 1850 A2 1855 A3 1860 D 1865 B1 1870 B2 1875 B3 1880 E 1885 F 1890 Uplink Frequency Table 1900MHz Band Structure PCS 1900 repeater has 5MHz, 10MHz, 15MHz Paths in IF division, so any of these bandwidths can be selected for providing service. 5MHz, 10MHz, 15MHz are only continious bands.
Sprint User Manual 3G Indoor Repeater 3. SPECIFICATIONS 3.1 System Capacity Item Freq.
Sprint User Manual 3G Indoor Repeater 3.2 System Specifications Parameter Specification Range 52dB ~ 72dB Adjust Step ±1.0dB Adjust Accuracy ±0.5dB Gain Propagation Remark < 5.0us Delay Spurious F0±885kHz < -45dBc ∆marker: 29dB Emission F0±1.98MHz < -55dBc ∆marker: 39dB Out Band Spurious Emission < -13dBm RBW: 30MHz Flatness < 3dB Return Loss / VSWR < 1.5 : 1 Uplink < 5dB @ Max gain Noise Figure < 12dB @ Min gain Roll off > 50dBc ±1.
Sprint User Manual 3G Indoor Repeater 3.
Sprint User Manual 3G Indoor Repeater Power Monitoring • Monitoring repeater’s output level Function DL Input control • Monitoring Donor ANT input power of DL Automatic • When repeater is shutdown, it periodically recovers output power of repeater then monitors Recovery alarming Security Temperature Control IP address report via E-mail • Support HTTPS for Web Browser security • User authentication through User ID and Password • Monitoring temperature of repeater • Maximum and minimum set up is poss
Sprint User Manual 3G Indoor Repeater 4. SETUP 4.1. Equipment Needed for GRS-1915D-SPR Repeater Setup Parameter Item Quantity Remark Major Component GRS-1915D-SPR 1 EA Provided by GST CD which contains User Manual 1 EA V0.1 and Installation Guide V0.1 Additional Components Ethernet Cable 6.6ft 1 EA AC/DC Adapter 1 EA Ground Cable 6.
Sprint User Manual 3G Indoor Repeater 4.1.2 System Setup 1) This equipment is basically wall mountable. 2) Installer will have to connect the power supply (after verifying the input power) and RF cable to the Repeater and then it will be ready to use. 3) For grounding, there is a grounding terminal in main power supply which will be plugged into power outlet. There is also a separate grounding terminal on the repeater which should be connected to the on-site grounding terminal to ensure proper grounding.
Sprint User Manual 3G Indoor Repeater 4.1.3 Open for Service 1) Check points before open: a. Verification of system installation status: - Electricity, In/Out antennas, cable connection, and equipment mount status. b. Verification of system accessories: - User should check all necessary accessories. c. Check receipt signal level - Installer should check whether environmental conditions are in accordance with system specification to ensure that system operation will be optimized.
Sprint User Manual 3G Indoor Repeater Front LED b. Verification of operation status User should verify following status with Output monitoring terminal, which is provided by Spectrum Analyzer: - Output power generation status, system spurious emission characteristics. c. Verification of signal quality and strength in service area User should verify signal strength and quality of in-service coverage area by using cell phone or other measuring device. d.
Sprint User Manual 3G Indoor Repeater 4.2 Troubleshooting In case of abnormal operation, technician should diagnose abnormality via remote access or directly connecting to repeater using Ethernet cable. If technician is required to conduct repairs due to major alarm, repeater should first be powered off, and then technician should prepare the proper measurement equipment before trying to fix the problem.
Sprint User Manual 3G Indoor Repeater 4.2.
Sprint User Manual 3G Indoor Repeater 4.2.
Sprint User Manual 3G Indoor Repeater * Technician should connect When output antenna with output port of * Reconnect the connector. power is no repeater. * Change it if the connector is defective. longer problem * Please make sure all connectors are fastened When output power is no * Check the input level * Increase output power or check input change of BTS side.
Sprint User Manual 3G Indoor Repeater In case Output * Check connection fastened Signal between antenna and cable wavelength is (Signal wavelength should be * If connection is not proper, reconnect cable and connector not shown flat flat and stable if technicians and then check the output power again. or looks like shake CABLE. If not, it is oscillation connection problem.) Same as above Same as above * Input level change or module overheating.