DOCUMENT TRACKING – REMOVE THIS SECTION BEFORE FINAL PRODUCTION Date By Notes 8/10/2011 Kevin Lewis New version 1.01.
Meter Reader RPS1005 RPS1015
Table of Contents Introduction Pulse Reader Overview Installation Safety Information About GreenWave 1 2 3 7 10
Introduction The GreenWave Reality platform helps create a smart, energy-efficient energy efficient home through the monitoring and controlling of your appliances and electronics (referred to as “devices”). You can conserve energy with minimal impact to your lifestyle by using our products to easily manage your devices.
Pulse Reader Overview The GreenWave Reality Pulse Reader connects to your electric and/or gas meters to measure energy usage. The information read through the Pulse Reader can then be transmitted to your GreenWave Reality R Gateway so that you can monitor and control your energy use. The Pulse Reader is weather-resistant resistant and designed to be mounted next to your electric and/or gas meters.
Installation You must follow several installation steps to connect your Pulse Reader to your meter. These steps include: • Preparing for installation • Attaching the self-adhesive adhesive template to the meter to ensure accurate placement of the sensors • Attaching the Pulse Reader sensors to your meter(s) • Installing batteries, if they are not already pre-installed pre • Securing the Pulse Reader unit in place near your meter(s) 1.
current reading and the base value: The exact target area on your meter depends on whether it is an electric or gas meter, as well as the specific type. 2. Attach Template to Meter Since placement of the Pulse Reader cable sensor on the meter is critical, your kit includes self-adhesive templates to help you align the sensor. Visually align the marking on the template to the target placement on your meter.
3. Attach Sensor to Meter Before removing the adhesive backing from the cable sensor, make sure it aligns correctly over the open area of the template. The grey-colored sensor attaches to your gas meter, and the white-colored sensor attaches to your electric meter. As you align the sensor over the template, make sure there will be no overhang of the sensor that might extend far over the template area.
5. Secure Pulse Reader Next to Meter Using the self-adhesive Velcro strips, mount the Pulse Reader unit to a stable location near your meters. Make sure there is no tension on the sensor cables attached to the meter.
Safety Information Batteries Use only lithium FR6 AA batteries. WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk: • Carefully follow all instructions and warnings on the battery label and package. • Always insert batteries correctly with regard to polarity (+ and -)) marked on the battery and a the equipment. • Do not short battery terminals. • Do not mix old and new batteries.
• Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools, etc. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibits transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits.
Directive Annex 1, this product is classed as category 3 “IT and Telecommunications Equipment.” DO NOT DISPOSE IN DOMESTIC HOUSEHOLD WASTE. To return unwanted products, contact your local GreenWave Reality office for more information (see contact information in the back of manual).
About GreenWave GreenWave Reality is a global innovator in the emerging home energy management anagement market. GreenWave Reality provides an affordable, easy-to-use, use, standards-based standards platform that allows utilities to enhance their relationship with consumers and better balance energy on the grid while consumers can conserve energy with a minimal impact to their lifestyle by easily monitoring and controlling their appliances and adding intelligent LED lighting.
Document Version 1.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Declaration(s) of Conformity These CE Marked GreenWave Reality products incorporating Radio and Telecoms Terminal Equipment functionality are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the original CE Declaration of Conformity is on file and available upon request for all CE Marked GreenWave Reality products. Please visit www.greenwavereality.com to obtain a copy of the Declaration.
www.greenwavereality.