Frontier FiOS Gateway USER GUIDE Model: FiOS-G1100 Copyright © 2016 Greenwave Systems. All Rights Reserved.
CONTENTS 01/ INTRODUCTION . 1.0 Package Contents . 1.1 System Requirements . 1.2 Features . 1.3 Getting to Know Your Gateway 02/ CONNECTING YOUR GATEWAY 2.0 Setting Up Your Gateway 03/ WIRELESS SETTINGS 3.0 Overview 3.1 Wireless Status 3.2 Basic Security Settings 3.3 Advanced Security Settings 3.4 Wireless MAC Authentication 3.5 802.11 Mode Copyright © 2016 Greenwave Systems. All Rights Reserved.
.6 Other Advanced Wireless Options 3.7 Guest Wi-Fi Settings 04/ CONFIGURING MY NETWORK SETTINGS . 4.0 Accessing My Network Settings . 4.1 Using My Network Settings . 4.2 Computer Network Configuration . 4.3 Main Screen 05/ CONFIGURING MY NETWORK SETTINGS . 5.1 Network (Home/Office) Connection . 5.2 Broadband Connection . 5.3 Wireless Access Point Connection . 5.4 Broadband Ethernet/Coax Copyright © 2016 Greenwave Systems. All Rights Reserved.
06/ ADVANCED NETWORK SETTINGS 6.1 Port Forwarding 6.2 Port Triggering 6.3 DMZ Host 07/ SETTING PARENTAL CONTROLS 7.0 Activating Parental Controls 7.1 Rule Summary 08/ CONFIGURING ADVANCED SETTINGS MONITORING YOUR GATEWAY . 8.0 Using Advanced Settings . 8.1 Utilities . 8.2 DNS Settings . 8.3 Network Settings . 8.4 Routing . 8.5 Date and Time 167 Copyright © 2016 Greenwave Systems. All Rights Reserved.
. 8.6 Configuration Settings 09/ Monitoring 9.1 System Logging 9.2 Full Status/System wide Monitoring 9.3 Bandwidth Monitoring 10/ TROUBLESHOOTING 10.0 Troubleshooting 189 Tips 10.1 Frequently 195 Asked Questions of Connections 9.4 Traffic 185 11/ SPECIFICATIONS . 11.0 General Specifications . 11.1 LED Indicators . 11.2 Environmental Parameters Copyright © 2016 Greenwave Systems. All Rights Reserved.
12/ NOTICES 12.0 Regulatory 207 Compliance Notices Copyright © 2016 Greenwave Systems. All Rights Reserved.
01/ INTRODUCTION . 1.0 Package Contents . 1.1 System Requirements . 1.2 Features . 1.3 Getting to Know Your Gateway The FiOS Gateway lets you transmit and distribute digital entertainment and information to multiple devices in your home/office. Your Gateway supports networking using coaxial cables, Ethernet, or Wi-Fi, making it one of the most versatile and powerful gateways available. PACKAGE CONTENTS, SYSTEM REQUIREMENTS AND FEATURES Copyright © 2016 Greenwave Systems. All Rights Reserved.
1.0/ PACKAGE CONTENT Your package contains: • The Frontier FiOS Gateway • Power adapter • LAN Ethernet cable (yellow) • WAN Ethernet cable (white) • Quick Start Guide 1.1/ SYSTEM REQUIREMENTS System and software requirements are: • A computer or other network device supporting Wi-Fi or wired Ethernet • A web browser, such as ChromeTM, Firefox®, Internet Explorer 8® or higher, or Safari® 5.1 or higher 1.
– MoCA 2.0 and 1.1 enabled to support speeds up to 700 Mbps over coaxial cable • Integrated wireless networking with 802.11b/g/n/ac access point featuring: – Enabled 802.11b capable speeds (based on device) – Enabled 802.11g capable speeds (based on device) – Enabled 802.11n capable speeds (based on device) – Enabled 802.
FEATURES AND GETTING TO KNOW YOUR GATEWAY – Port forwarding – Port triggering – Access control – Advanced wireless protection featuring WPA2/WPA Mixed Mode, WEP 64/128 bit encryption, and MAC address filtering • Options, including: – DHCP server – WAN interface auto-detection – Dynamic DNS – DNS server – LAN IP and WAN IP address selection – MAC address cloning – IPv6 support – QoS support (end to end layer 2/3) featuring: Differentiated Services (Diffserv), 802.
– Static routing – VPN (VPN pass through only) 01/ INTRODUCTION 10 – IGMP – Daylight savings time support 1.3/ GETTING TO KNOW YOUR GATEWAY 1.3a/ FRONT PANEL The front panel has two lighted indicators and a WPS (Wi-Fi Protected Setup) button. The Power/Internet light will be on and solid when your Gateway is turned on, connected to the Internet, and functioning normally. The Wireless light will be on when your Gateway Wi-Fi is turned on.
GETTING TO KNOW YOUR GATEWAY If there is an error during the WPS pairing process, the wireless light flashes red rapidly for two minutes after the error occurs. The WPS button can also be used to reboot the router. To perform a soft reboot, press and hold the WPS button for at least 10 seconds. 1.
GETTING TO KNOW YOUR GATEWAY • USB - provides up to 500 mA at 5 VDC for attached devices. For example, you could charge a cell phone. In the future, with a firmware upgrade, the USB host functionality may be available for other devices, such as external storage and cameras. Firmware updates are performed automatically by Frontier. • Reset Button - allows you to reset your Gateway to the factory default settings. To reset the Gateway, press and hold the Reset button for at least three seconds.
If you are replacing an existing wall mounted router, you do not need to remove the mounting screws from the wall. The existing mounting screws will fit the new bracket. To mount your Gateway to a wall: 1. Remove the foot by turning the Gateway upside down and removing the single screw that holds the foot to the Gateway. 2. Slide the foot toward the front of the Gateway and pull the foot from the holes. You may need to wiggle the foot slightly. 3.
9. To secure the Gateway, attach the bracket to the Gateway using the single screw you removed from the foot. 10. Slidethewallmount bracket with the attached Gateway on the screws, then slide the bracket down until it locks in place. Copyright © 2016 Greenwave Systems. All Rights Reserved.
02/ CONNECTING YOUR GATEWAY . 2.0 Setting Up Your Gateway . 2.1 Computer Network Configuration . 2.2 Main Screen SETTING UP YOUR GATEWAY Connecting your Gateway and accessing its web-based Graphical User Interface (GUI) are both simple procedures. Accessing the GUI may vary slightly, depending on your device’s operating system and web browser. Copyright © 2016 Greenwave Systems. All Rights Reserved.
2.0/ SETTING UP YOUR GATEWAY There are three basic steps to setting up your Gateway: Step1: Connect your Gateway to the Internet Step 2: Connect your network device to your Gateway Step 3: Configure your Gateway Before you begin, if you are replacing an existing Gateway, disconnect it. Remove all old Gateway components, including the power supply. They will not work with your new Gateway. 2.0a/ STEP 1 - CONNECT YOUR GATEWAY 1. Remove your Gateway, Ethernet cables, and power adapter from the box. 2.
Tighten the coaxial cables by hand until snug. The cables should not require a wrench. 4. Plug the power cord into the power port on the back of your Gateway and then into a power outlet. The Gateway automatically turns on as soon as power is plugged in. Important: Wait until the Power/Internet light on the front of the Gateway stops flashing and is solid white. If the light turns red, check the troubleshooting steps in the Troubleshooting section of the user guide. 2.
2.0c/ STEP 3 - CONFIGURE YOUR GATEWAY: 1. Open a web browser on the device connected to your Gateway network. 2. In the browser address field (URL), enter: myfiosgateway.com, then press the Enter key on your keyboard. Alternately, you can enter: https://192.168.1.1 SETTING UP YOUR GATEWAY The first time you access your Gateway, an Easy Setup Wizard displays to help step you through the setup process. 3.
Wi-Fi changes to your Gateway. Important: If you are on a Wi-Fi device when setting up your Gateway, you will be disconnected from the Wi-Fi network when you change the Wi-Fi name or Wi-Fi password. When this occurs, your Gateway will detect this situation and prompt you to reconnect using the new settings. Congratulations! You’re All Set Up screen displays once your Gateway verifies the final settings and has successfully connected to the Internet and is ready for use.
2. In the View your active networks – Connect or disconnect section, click Local Area Connection in the Connections field. The Local Area Connection Status window displays. 3. Click Properties. The Local Area Connection Properties window displays. 4. Select Internet Protocol Version 4 (TCP/IPv4), then click Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties window displays. 5. Click the Obtain an IP address automatically radio button. 6.
displays Connected. 5. Click Assist Me. 6. Follow the instructions in the Network Diagnostics Assistant. 2.1b/ CONNECTING OTHER COMPUTERS & NETWORK DEVICES You can connect your Gateway to other computers or set top boxes using an Ethernet cable, wireless connection (Wi-Fi), or coaxial cable. ETHERNET 1. Plug one end of an Ethernet cable into one of the open yellow Ethernet ports on the back of your Gateway. 2. Plug the other end of the Ethernet cable into an Ethernet port on the computer. 3.
to join your wireless network. To initialize the WPS process, you can either press and release the WPS button located on the front of your Gateway or use the GUI and press the on-screen button. You can easily add wireless devices to your wireless network using the WPS option if your wireless device supports the WPS feature. To access WPS using the user interface: 1. From the Main menu, select Wireless Settings, then select Wi-Fi Protected Setup (WPS). 2.
supported by your wireless device. 4. After pressing the WPS button on your Gateway, you have two minutes to press the WPS button on the client device before the WPS session times out. When the WPS button on your Gateway is pressed, the Wireless light on the front of your Gateway begins flashing white. The flashing continues until WPS pairing to the client device completes successfully. At this time, the Wireless light turns solid white.
to your Gateway. COAXIAL 1. Verify all coax devices are turned off. 2. Disconnect any adapter currently connected to the coaxial wall jack in the room where your Gateway is located. 3. Connect one end of the coaxial cable to the coaxial wall jack and the other end to the Coax port on your network device. 4. Power up the network device. 2.
• Advanced - Chapter 8 • System Monitoring - Chapter 9 2.2b/ STATUS This section displays the status of your Gateway’s local network (LAN) and Internet connection (WAN).
Additional Resources The Additional Resources section contains links to various web sites and other informational links. Note: You may see an alert when using an older 802.11b device indicating the Wi-Fi network performance maybe affected, as shown in the example below. Copyright © 2016 Greenwave Systems. All Rights Reserved.
03/ WIRELESS SETTINGS . 3.0 Overview . 3.1 Wireless Status . 3.2 Basic Security Settings . 3.3 Advanced Security Settings . 3.4 Wireless MAC Authentication . 3.5 802.11 Mode . 3.6 Other Advanced Wireless Options . 3.7 Guest Wi-Fi Settings OVERVIEW Wireless networking enables you to free yourself from wires and plugs, making Copyright © 2016 Greenwave Systems. All Rights Reserved.
your devices more accessible and easier to use. You can create a wireless network, including accessing and configuring wireless security options. 3.0/ OVERVIEW Your Gateway provides you with wireless connectivity using the 802.11b, g, n, or ac standards. These are the most common wireless standards. 802.11b has a maximum data rate of 11 Mbps, 802.11g has a maximum data rate of 54 Mbps, 802.11n has a maximum data rate of 450 Mbps, and 802.11ac has a maximum data rate of 1300 Mbps. 802.
Your Gateway integrates multiple layers of security. These include Wired Equivalent Privacy (WEP), Wi-Fi Protected Access (WPA/WPA2), and firewall. OVERVIEW 3.1/ WIRELESS STATUS Use the Wireless Status feature to view the status of your Gateway’s wireless network. To view the status: 1. Access the Main page. You can quickly view your Gateway’s wireless status in the My Network column. This includes all devices that have recently accessed or are currently connected to the network. 2.
using. • Security Enabled - displays the type of security active on the wireless connection as well as the security encryption key. • SSID Broadcast - displays whether your Gateway is broadcasting its SSID. If activated, the SSID of your Gateway wireless network is broadcast wirelessly. If not activated, the SSID is hidden and the wireless clients must be manually configured to use the SSID.
2. To activate the wireless radio, click the On radio button. 3. If desired, enter a new name for the wireless network in the SSID field or leave the default name that displays automatically. 4. Select the channel you want the wireless radio to use to communicate or accept the default Automatic channel, then select the Keep my channel selection during power cycle check box to save your channel selection when your Gateway is rebooted.
displays. To set the WPA2 security: 1. Enter the Pre-Shared Key. 2. To activate the group key update interval, select the Group Key Update Interval check box and set the interval time in seconds. 3. Click Apply to save the changes. Warning: WEP provides a low level of security and is not recommended. Additionally, the WEP security setting will drop your Gateway’s wireless performance to a maximum data rate of 54 Mbps, and will disable Wi-Fi Protected Setup (WPS).
radio button. 6. Select a WEP security level as 64/40 bit or 128/104 bit. 7. Enter the key code. If using a HEX key, each character mustbealetterfromAtoForanumberfrom0to9.If the key is ASCII, each character can be either any ASCII or alphanumeric character. If using 64/40 bit, enter 10 HEX or 5 ASCII/alphanumeric characters. If 128/104, enter 26 HEX or 13 ASCII/ alphanumeric characters. 8. Be sure to write down the wireless settings for future use.
on your selection, one of the following pages displays. 3.3/ ADVANCED SECURITY SETTINGS ADVANCED SECURITY SETTINGS 3.3b/ LEVEL 1: SSID BROADCAST You can configure your Gateway’s SSID broadcast capabilities to allow or disallow wireless devices from automatically using a broadcast SSID name to detect your Gateway wireless network. To enable or disable SSID broadcast: 1. In the Advanced Settings page, locate the Level 2 section. 2. Click the 2.
3.3c/ LEVEL 2: LIMIT ACCESS You can configure your Gateway to limit access to your wireless network allowing access only to those devices with specific MAC addresses or based on the type of wireless technology used. ADVANCED SECURITY SETTINGS To limit access: 1. In the Advanced Settings page, locate the Level 2 section. 2. To allow only devices with specific MAC addresses, click the Wireless MAC Authentication link. The Wireless MAC Authentication page displays.
the Wireless MAC Authentication link. The Wireless MAC Authentication page displays. 2. To enable access control, select the Enable Access List check box. 3. Select either: • Accept all devices listed below – allows only the listed devices to access the wireless network. Warning: This will block wireless network access for all devices not in the list. Only devices in the list will be able to connect to the wireless network. • Deny all devices listed below – denies access to the listed devices.
• Repeat step 2 to add additional devices, as needed. 802.11 MODE To select the 802.11 Mode: 1. On the Advanced Settings page, locate the Level 2 section and click the 802.11 Mode link. The 802.11 Mode page displays. 2. Select the 2.4 GHz Wireless Mode as follows: • Compatibility – This is the default mode setting, providing a good balance of performance and compatibility with existing wireless devices. 802.11b, g, and n devices can connect. • Legacy – For older wireless devices. Only 802.
3.6/ OTHER ADVANCED WIRELESS OPTIONS You can view additional wireless options. Comment: Recommend leaving defaults as is unless otherwise directed. To view the options: 1. In the Advanced Settings page, locate the Level 2 section and click Other Advanced Wireless Options link. A warning message displays. 2. Click Yes. The Other Advanced Wireless Options page displays. Comment: The following example uses the 2.4 GHz network. The display configuration looks basically the same for the 5 GHz network.
networks to operate at maximum efficiency • CTS Protection Type – displays cts, which is only for mixed 802.11b/g/n/ac networks or rts_cts, which is for 802.
3.6a/ WMM SETTINGS You can prioritize the types of data transmitted over the wireless network using the advanced WMM settings. Wireless QoS (WMM) can improve the quality of service (QoS) for voice, video, and audio streaming over Wi-Fi by prioritizing these data streams. WMM Power Save can improve battery life on mobile Wi-Fi devices such as smart phones and tablets by fine-tuning power consumption. WMM (Wi-Fi Multimedia) QoS and Power Save require a wireless client device which also supports WMM.
either the Gateway’s web interface, or via the My app. • Click Yes. The WMM Settings page displays. • To enable Wireless QoS (WMM), select the Enabled check box. GUEST WI-FI SETTINGS guest network SSID does not change when you make a change to your primary network SSID. The Gateway is shipped from the factory with Guest Wi-Fi turned off.
3.7b/ GUEST DEVICES The devices on the Guest Wi-Fi network can be viewed on the Guest Devices page. If the admin toggles the button next to a device to OFF, that device will be blocked from accessing the Internet. Copyright © 2016 Greenwave Systems. All Rights Reserved.
04/ CONFIGURING MY NETWORK SETTINGS . 4.0 Accessing My Network Settings . 4.1 Using My Network Settings ACCESSING MY NETWORK SETTINGS You can configure the basic network settings for your Gateway’s network. My Network allows you to view and manage your network connections and devices. You can block websites and Internet services, set port forwarding, view device details, and rename devices. To view your network connections: 1. On the Main page, select the My Network icon.
Caution: The settings described in this chapter should only be configured by experienced network technicians. Changes could adversely affect the operation of your Gateway and your local network. 4.0/ ACCESSING MY NETWORK SETTINGS USING MY NETWORK SETTINGS 4.1/ USING MY NETWORK SETTINGS You can access and configure common network parameters: • Block this Device - Click Block this Device to quickly enable/disable a device from having Internet access.
information, refer to the Port Forwarding section in Chapter 6 Configuring Security Settings. • View Device Details - Click View Device Details to display the Device Information page and view the selected device’s information, such as IP Address, MAC address, Network Connection, Lease Type, Port Forwarding Services, and Windows Shared Folder as well as the Ping Test option. You can also click the device’s icon in the Main page to display the Device Information page.
05/ USING NETWORK CONNECTIONS . 5.0 Accessing Network Connections . 5.1 Network (Home/Office) Connection . 5.2 Ethernet/Coax Connection . 5.3 Wireless Access Point Connection . 5.4 Broadband Ethernet/Coax Connection Your Gateway supports various local area network (LAN) and wide area network (WAN), or Internet connections using Ethernet or coaxial cables. You can configure aspects of the network and Internet connections as well as create new connections. Copyright © 2016 Greenwave Systems.
ACCESSING NETWORK CONNECTIONS Caution: The settings described in this chapter should only be configured by experienced network technicians. Changes could adversely affect the operation of your Gateway and your local network. 5.0/ ACCESSING NETWORK CONNECTIONS You can access your network connections and view the connections by connection type. To access the network connections: 1. Select My Network, then select Network Connections. 2. To display all connection entries, click the Advanced button. 3.
To view the connection: 1. On the Network Connections page, click the Network (Home/Office) connection link. The Network (Home/Office) Properties page displays. 2. To rename a network connection, enter the new network name in the Name field. 3. Click Apply to save the changes. CONFIGURING THE HOME/OFFICE NETWORK To configure the network connection: 1. In the Network (Home/Office) Properties page, click Settings. The configuration page displays. 2. Configure the following sections, as needed.
– Automatic - sets the MTU at 1500 – Automatic by DHCP - sets the MTU according to the DHCP connection – Manual - allows you to manually set the MTU • Internet Protocol - in the internet protocol section, specify one of the following – Use the Following IP Address - the network connection uses a permanent or static IP address and subnet mask address, provided by an experienced network technician.
to configure your Gateway’s Dynamic Host Configuration Protocol (DHCP) server parameters. NETWORK (HOME/OFFICE) CONNECTION Once enabled and configured, the DHCP server automatically assigns IP addresses to any network devices which are set to obtain their IP address dynamically. If DHCP Server is enabled on your Gateway, configure the network devices as DHCP Clients. There are 2 basic options in this section: Disabled and DHCP Server. To set up the Gateway’s network bridge to function as a DHCP server: 1.
4. Click Apply to save changes. ROUTING You can configure your Gateway to use static or dynamic routing. • Static routing – specifies a fixed routing path to neighboring destinations based on predetermined metrics. • Dynamic routing – automatically adjusts how packets travel on the network. The path determination is based on network/device reachability and status of network being traveled. To configure routing: 1.
3. Click Apply to save changes. ETHERNET/COAX CONNECTION 5.2a/ CONFIGURING THE ETHERNET/COAX CONNECTION To configure the connection: 1. In the Broadband Connection (Ethernet/Coax) Properties page, click Settings. The configuration page displays. 2. Configure the following settings, as needed. GENERAL Verify the following information: • Status - displays the connection status of the network. • Network – displays the type of network connection. • Connection Type - displays the type of connection.
2. Select the On or Off radio button in the Auto Detection field. 3. To set privacy, select the Enabled check box. This causes all devices connected to the coaxial cable to use the same password. This is recommended. 4. To set the password, enter the Coax Link password in the Password field. • MTU - specifies the largest packet size permitted for Internet transmissions: ETHERNET/COAX CONNECTION 5. To enable or disable the Coax link, click Disable or Enable. 6.
1. In the Network Connections page, click Advanced. 2. Click 5 GHz Wireless Access Point 1 or 2.4 GHz Wireless Access Point WIRELESS ACCESS POINT CONNECTION 3. To disable the connection, click Disable. 4. To rename the connection, enter a name in the Name field. 5. Click Apply to save the changes. 6. Reboot your Gateway. 5.3a/ CONFIGURING WIRELESS ACCESS POINT PROPERTIES To configure the connection: 1. In the Wireless Access Point Properties page, click Settings. The configuration page displays. 2.
– Automatic by DHCP - sets the MTU according to the DHCP connection WIRELESS ACCESS POINT CONNECTION AND BROADBAND ETHERNET/COAX CONNECTION – Manual - allows you to manually set the MTU 3. Click Apply to save changes. 5.4/ BROADBAND ETHERNET/COAX CONNECTION A Broadband Ethernet connection connects computers to your Gateway using Ethernet cables. The connections are either direct or use network hubs and switches.
Settings. The configuration page displays. BROADBAND ETHERNET/COAX CONNECTION 2. Configure the following settings, as needed.
recommended. 4. To set the password, enter the Coax Link password in the Password field. 5. To enable or disable the Coax link, click Disable or Enable. 6. To view the devices connected using the coaxial cable, click the Go to WAN Coax Stats link. BROADBAND ETHERNET/COAX CONNECTION INTERNET PROTOCOL 1. In the Internet Protocol section, specify one of the following: • No IP Address – the connection has no IP address. This is useful if the connection operates under a bridge.
COMPLETE ALL ETHERNET/COAX CONNECTION CONFIGURATION UPDATES To save your changes: 1. Click Apply. Copyright © 2016 Greenwave Systems. All Rights Reserved.
06/ CONFIGURING SECURITY SETTINGS . 6.0 Firewall . 6.1 Access Control . 6.2 Port Forwarding . 6.3 Port Triggering . 6.4 DMZ Host . 6.5 Remote Administration . 6.6 Static NAT . 6.7 Security Log Your Gateway’s security suite includes comprehensive and robust security services, such as stateful packet inspection, firewall security, user authentication Copyright © 2016 Greenwave Systems. All Rights Reserved.
protocols, and password protection mechanisms. These and other features help protect your computers from security threats on the Internet. FIREWALL This chapter covers the following security features: • Firewall - select the security level for the firewall. • Access Control - restrict access from the local network to the Internet. • Port Forwarding - enable access from the Internet to specified services provided by computers on the local network.
• Security Log - view and configure the security log. 6.0/ FIREWALL The firewall is the cornerstone of the security suite for your Gateway. It has been exclusively tailored to the needs of the residential or office user and is pre-configured to provide optimum security. The firewall provides both the security and flexibility home and office users seek.
For example, when accessing a website on the Internet, a request is sent to the Internet for this site. When the request reaches your Gateway, the firewall identifies the request type and origin, such as HTTP and a specific computer in the local network. Unless your Gateway is configured to block requests of this type from this computer, the firewall allows this type of request to pass to the Internet.
Minimum Unrestricted Unrestricted The request access is defined as: • Blocked traffic - no access allowed, except as configured in Port Forwarding and Remote Access • Limited - permits only commonly used services, such as email and web browsing • Unrestricted - permits full access of incoming traffic from the Internet and allows all outgoing traffic, except as configured in Access Control 1. From the Firewall General settings page click on desired IPv6 option to configure IPv6 security: 6.
block one computer from accessing the Internet, then block a second computer from transferring files using FTP as well as prohibit the computer from receiving incoming email. Access control incorporates a list of preset services, such as applications and common port settings. 6.1a/ ALLOW OR RESTRICT SERVICES To allow or restrict services: 1. From the Firewall page, select Access Control. The Access Control page opens with the Allows and Blocked sections displayed.
6. Click Apply to save changes. The Access Control page displays a summary of the new access control rule. 6.1b/ DISABLE ACCESS CONTROL You can disable an access control and enable access to the service without removing the service from the Access Control table. This can make the service available temporarily and allow you to easily reinstate the restriction later. • To disable an access control, clear the check box next to the service name.
drop down. 3. Select the application in the Application to Forward drop down. 4. Click Add. The rule displays in the Applied Rules section. 5. Click Apply to save changes. 6.2a/ ADVANCED PORT FORWARDING RULES You can configure advanced port forwarding rules. To configure the rules: 1. In the Port Forwarding page, select Advanced. 2. If needed, to select a port to forward communication to, select an option in the Forward to Port list box. 3.
UDP on port 3333, when a gaming session is initiated. In this case, port triggering must be used since it conflicts with the following default firewall settings: • Firewall blocks inbound traffic by default. • Server replies to your Gateway IP, and the connection is not sent back to the host since it is not part of a session.
DMZ Host allows a single device on your primary network to be fully exposed to the Internet for special purposes like Internet gaming. DMZ HOST Warning: Enabling DMZ Host is a security risk. When a device on your network is a DMZ Host, it is directly exposed to the Internet and loses much of the protection of the firewall. If it is compromised, it can also be used to attack other devices on your primary network. Follow these steps to designate a device on your primary network as a DMZ Host: 1.
• Web Management - used to obtain access to your Gateway’s GUI and gain access to all settings and parameters through a web browser. • Diagnostic Tools - used for troubleshooting and remote system management by a user or your Frontier. Web Management remote administration access may be used to modify or disable firewall settings. Local IP addresses and other settings can also be changed, making it difficult or impossible to access your Gateway from the local network.
Static NAT allows devices located behind a firewall that is configured with private IP addresses to appear to have public IP addresses to the Internet. This allows an internal host, such as a web server, to have an unregistered (private) IP address and still be accessible over the Internet. To configure static NAT: 1. Select Static NAT. 2. To create a static NAT, click Add. The Add NAT/NAPT Rule page displays. 6.6/ STATIC NAT STATIC NAT AND SECURITY LOG 3.
administrative interface, such as your Gateway GUI, firewall configuration, and system start-up. • Time - based on the date and time in your Gateway • Event Type - consists of firewall information, firewall setup, and system log • Log Level - describes the event that occurred, such as a fragmented packet or parental controls. • Details - provide a reason the event occurred, such as a packet has been blocked because of parental controls. You can modify the type of events that display in the security log.
SECURITY LOG • Default policy – a packet has been accepted/blocked according to the default policy. • Defragmentation failed – the fragment has been stored in memory and blocked until all fragments have arrived and defragmentation can be performed. • DHCP request – your Gateway sent a DHCP request (depends on the distribution). • DHCP response - your Gateway sent a DHCP response (depends on the distribution).
after defragmentation, the packet was badly aligned. • Fragmented packet, header too big – a packet has been blocked because, after defragmentation, the header was too big. • Fragmented packet, header too small – a packet has been blocked because, after defragmentation, the header was too small. • Fragmented packet, overlapped – a packet has been blocked because, after defragmentation, there were overlapping fragments.
• Malformed packet: Failed parsing – a packed has been blocked because it is malformed. • Maximum security enabled service – a packet has been accepted because it belongs to a permitted service in the maximum security level. • Fragmented packet, no memory – a packet has been blocked because there is no memory for fragments. SECURITY LOG • Multicast IGMP connection – a multicast packet has been accepted.
packet has been blocked. • Service – a packet has been accepted because of a certain service, as specified in the event type. • Spoofing protection – a packet from the Internet with a source IP belong to the local network has been blocked. • STP packet – STP (Spanning Tree Protocol) packet has been accepted/rejected. • SynCookies protection – a SynCookies packet has been blocked. • Trusted device – a packet from a trusted device has been accepted.
SECURITY LOG 3. In the Accepted Events section, select the type of activities that generates a log message: • Accepted Incoming Connections – generates a log message for each successful attempt to establish an inbound connection to the local network. • Accepted Outgoing Connections - generates a log message for each successful attempt to establish an outbound connection to the public network. 4. In the Blocked Events section, select the type of blocked events you want logged. 5.
07/ SETTING PARENTAL CONTROLS . 7.0 Activating Parental Controls . 7.1 Rule Summary The abundance of harmful information on the Internet poses a serious challenge for employers and parents alike as they ask “How can I regulate what my employee or child does on the Internet?” With that question in mind, your Gateway’s Parental Controls were designed to allow control of Internet access on all locally networked devices. Copyright © 2016 Greenwave Systems. All Rights Reserved.
ACTIVATING PARENTAL CONTROLS 7.0/ ACTIVATING PARENTAL CONTROLS You can create a basic access policy for any computer or device on your Gateway network. Parental controls limit Internet access to specific websites based on a schedule that you create. Access can be limited on specific websites or keywords embedded in a website. For example, you can block access to the ‘www.anysite.com’ as well as block any website that has the word ‘any’ in its site name. To limit computer access: 1. Select Parental Controls.
• Block ALL Internet Access – will not allow the device to access the Internet. 5. Enter the name of the website or keyword, then click Add. 6. To remove a website or keyword, select the word, then click Remove. ACTIVATING PARENTAL CONTROLS AND RULE SUMMARY 7. Create a schedule by selecting the days of the week when the rule will be active or inactive. 8. Set the time when the rule will be active or inactive, then specify the start time and end time. 9. Create a rule name and description. 10.
08/ CONFIGURING ADVANCED SETTINGS . 8.0 Using Advanced Settings . 8.1 Utilities . 8.2 DNS Settings . 8.3 Network Settings . 8.4 Routing . 8.5 Date and Time . 8.6 Configuration Settings Advanced settings cover a wide range of sophisticated configurations for your Gateway’s firmware and network. USING ADVANCED SETTINGS AND UTILITIES Copyright © 2016 Greenwave Systems. All Rights Reserved.
Caution: Many of the settings described in this section should only be configured by experienced network technicians. Changes could adversely affect the operation of your Gateway and local network. 8.0/ USING ADVANCED SETTINGS You can access the following settings: Utilities DNS Settings Network Settings Configuration Settings To access the advanced settings: Date & Time Routing 1. Select Advanced. A warning page displays, asking if you want to proceed. 2. Click Yes. The Advanced page displays. 3.
• Quality of Service (QoS) – contact Technical Support for detailed information UTILITIES • Local Administration – allows you to grant local SSH access • Remove Administration – detailed in Chapter 6 Configuring Your Network Settings 8.1a/ DIAGNOSTICS You can use diagnostics to test network connectivity. To diagnose network connectivity: 1. Select Diagnostics in the Advanced page. 2. To ping an IP address, enter the IP address or domain name in the Destination field and click Go.
password. A user-specified password will no longer be valid. To restore your Gateway’s factory default settings: 1. Select Restore Defaults in the Advanced page. UTILITIES 2. To save your current configuration file, click Save Configuration File. 3. To restore the factory default settings, click OK. The factory default settings are applied and your Gateway restarts. Once complete, the Login page for the First Time Easy Setup Wizard displays. 8.
1. Select MAC Cloning in the Advanced page. 2. In the To Physical Address field, enter the MAC address of your new device. 3. To locate the MAC address, refer to the documentation from the device manufacturer. 4. Click Apply to save changes 8.1d/ MAC CLONING A MAC address is a hexadecimal code that identifies a device on a network. All networkable devices have a unique MAC address. UTILITIES 8.1e/ ARP TABLE You can view the IP and MAC addresses of each DHCP connection.
To view users: 1. Select Users in the Advanced page. 2. In the Login Configuration section, enter the maximum number of unsuccessful login attempts. 3. To edit usernames and passwords, click the Edit icon in the Action column. The User Settings page displays. UTILITIES 4. To edit the username and set a new password, as needed. 5. To add a new user, specify the following parameters: • Full Name - name of the user. • User Name – name the user enters to remotely access the home or office network.
2. To grant access, select the check box for the specific SSH access. 3. Click Apply to save changes. Local access is granted. 4. To remove access, clear the checkbox, then click Apply. No local access is granted. 8.1h/ REMOTE ADMINISTRATION The Remote Administration parameters are detailed in Chapter 4; Configuring Your Network Settings. DNS SETTINGS AND NETWORK SETTINGS 8.2/ DNS SETTINGS You can view and manage the DNS server host name and IP address as well as add a new computer.
1. Select Dynamic DNS 2. To set up a new entry, click the Add button. NETWORK SETTINGS 3. Configure the following parameters: • Host Name – enter the full domain name for your Dynamic DNS domain. • Provider – select the Dynamic DNS account provider from the menu. • User Name – enter your user name for your Dynamic DNS account. • Password – enter the password for your Dynamic DNS account. • SSL Mode – select if your Dynamic DNS service supports SSL. Click Apply to save your changes.
1. Select DNS Server in the Advanced page. 2. To view and add computers stored in the DNS table, click Add DNS Entry. The Add DNS Entry page displays. 3. In the Host Name field, enter the name of the computer, then enter the IP address and click Apply to save changes. The DNS Server page displays. 4. To edit the host name or IP address, click the Edit icon in the Action column. The DNS Entry page displays. Edit the host name and/or IP address, then click Apply to save changes. 5.
Website filtering can then be simultaneously applied to all the computers. You can use network objects to apply security rules based on host names, instead of IP addresses. This is useful since IP addresses change from time to time. In addition, you can define network objects according to MAC address to make the rule application more persistent against network configuration settings. To define a network object: 1. Select Network Objects in the Advanced page. 2. To define a network object, click Add.
UPnP services are not deleted when disconnecting a computer without proper shutdown of the UPnP applications, such as messenger. Services may often not be deleted and eventually this leads to the exhaustion of rules and services, and no new services can be define. The cleanup feature locates the invalid services and removes them, preventing services exhaustion. To access this setting: 1. Select Universal Plug and Play in the Advanced page. 2.
8.4/ ROUTING You can configure the following settings: • IPv6 – enables IPv6 support. • Routing – manages the routing and IP address distribution rules. • IP Address Distribution - adds computers configured as DHCP clients to the network 8.4a/ IPv6 Use the IPv6 feature settings to enable, disable, or configure an IPv6 Internet connection and IPv6 LAN settings. 1. To configure your network to use the IPv6 Internet connection type. Select IPv6 from the Advanced page to display the IPv6 service options: 2.
You should also see the IPv6 address for all IPv6 supported devices on your local network displayed on the My Network page and under the Broadband Connection (Ethernet/Coax) Properties as shown on the two pages below. STATIC - WAN IPv6 ADDRESS CONNECTION The IPv6 WAN Static configurations are IPv6 settings that you enter manually. These specific IPv6 addresses and settings are not expected to change frequently. 1.
• Default Gateway • Primary DNS Server • Secondary DNS Server • IPv6 LAN Configuration (select Stateful from the drop- down list) as shown in drop-down list and page below: • LAN Prefix • LAN IPv6 Link Local Address (automatically populated) • LAN IPv6 Address Range (start and end) • Router Advertisement Lifetime (minutes between 0-150) • IPv6 Address Lifetime (minutes between 3-150) • Interfaces - check one or more of the box(s) to apply IPv6 LAN settings to the selected interfaces: – Ethernet/Coax IPv6 En
below: 2.
2. Specify the DHCPv6 method to be used to obtain your WAN IPv6 Address by entering: • IPv6 WAN Configuration (select DHCPv6 from the drop- down list) as shown in drop-down list and page below: 3. Check to either ‘Obtain IPv6 DNS Server address automatically’, or to ‘Use the following IPv6 DNS Server addresses’ 4. After entering all appropriate IPv6 settings click Apply to have changes take effect. DHCPv6 WAN WITH LAN IPv6 STATEFUL (DHCPv6) SETTINGS: 1.
– Ethernet/Coax IPv6 Enabled – Wireless Access Point 1 IPv6 Enabled – Wireless Access Point 2 IPv6 Enabled 3. After entering all appropriate IPv6 settings click Apply to have changes take effect. DHCPv6 WAN WITH LAN IPv6 STATELESS SETTINGS: 1. To configure IPv6 LAN Stateless mode with DHCPv6 WAN, select the Stateless option on the IPv6 Configuration Control Page as shown below: 2.
3. After entering all appropriate IPv6 settings click Apply to have changes take effect. LAN IPv6 CONFIGURATION WITHOUT AN IPv6 WAN CONNECTION: 1. To configure IPv6 to use either the IPv6 LAN Stateful or Stateless mode without using an IPv6 Internet WAN connection, select the None option on the IPv6 Configuration Control Page as shown below: 2. After entering all appropriate IPv6 settings click Apply to have changes take effect. LAN IPv6 STATEFUL (DHCPv6) WITH NO WAN SETTINGS: 1.
– Wireless Access Point 1 IPv6 Enabled – Wireless Access Point 2 IPv6 Enable 3. After entering all appropriate IPv6 settings click Apply to have changes take effect. LAN IPv6 STATELESS WITH NO WAN SETTINGS: 1. To configure IPv6 LAN Stateless mode with No WAN connection, select the Stateless option on the IPv6 Configuration Control Page as shown below: 2.
8.4b/ ROUTING SETTINGS You can view the routing and IP address distribution rules as well as add, edit, or delete the rules. To view the rules: 1. Select Routing in the Advanced page. 2. To add a new Gateway, click Add New Route. 3. Specify the following parameters: • Name – select the network type. • Destination - enter the destination IP of the destination host, subnet address, network address, or default route. The destination for a default route is 0.0.0.0. • Netmask – enter the network mask.
For example, a client (host) sends a broadcast message on the network requesting an IP address for itself. The DHCP server then checks its list of available addresses and leases a local IP address to the host for a specific period of time and simultaneously designates this IP address as taken. At this point, the host is configured with an IP address for the duration of the lease. The host can renew an expiring lease or let it expire.
• Provides the DNS server with the host name and IP address of each computer connected to the network 1. On the IP Address Distribution page, click the Edit icon in the Action column. The DHCP Settings page opens with the device information displayed. To view a summary of the services provided by the DHCP server: 1. Select IP Address Distribution in the Advanced page. DHCP SERVER SETTINGS You can edit the DHCP server settings for a device. To edit the settings: ROUTING 2.
end IP address range that can be entered is 192.168.1.254. • WINS Server – determines the IP address associated with a network device. • Lease Time in Minutes – assigns the amount of time in minutes that each device is assigned an IP address by the DHCP server when it connects to the network. When the lease expires, the server determines if the computer has disconnected from the network. If it has, the server may reassign this IP address to a newly- connected computer.
Static Connection. 3. Enter the host name. 4. Enter the fixed IP address to be assigned. 5. Enter the MAC address of the network interface of the computer used with this DHCP static connection. 6. Click Apply to save changes. 8.5/ DATE AND TIME You can configure the following settings: • Date and Time Settings – sets the time zone and enables automatic time updates. • Scheduler Rules – limits the activation of firewall rules to specific time periods. 8.
DATE AND TIME 5. Enter the IP address or domain name of the time server, then click Apply to save changes. 8.5b/ SCHEDULER RULES Scheduler rules are used for limiting the activation of firewall rules to specific time periods. The time periods are either for days of the week or for hours of each day based on activity or inactivity. To define a rule: 1. Verify that the date and time of your Gateway is correct. 2. Select Scheduler Rules in the Advanced page. 3. Click Add. The Set Rule Schedule page displays.
8.6/ CONFIGURATION SETTINGS You can configure the following configuration settings: • Configuration File – used for file backups and restoring configuration files • System Settings – configures various system and management parameters • Port Configuration – sets up Ethernet ports 8.6a/ CONFIGURATION FILE You can use the Configuration File functionality to view, save, and load configuration files. These files are used to backup and restore the current configuration of your Gateway.
File. Browse to the location of the file, then click Apply to begin the configuration uploading process. Your Gateway will automatically restart with that configuration. 8.6b/ SYSTEM SETTINGS You can configure various system and management parameters. To configure system settings: 1. Select System Settings in the Advanced page. • Wireless Broadband Route’s Hostname – enter the host name or URL address of your Gateway. Both names are the same. • Local Domain – view the local domain of the network. 3.
4. Select Remote Administration to configure the remote administration to your Gateway. 5. In the Management Application Ports section, change the primary and secondary HTTP management ports. 6. In the System Logging section, configure the following system log options: • Enable Logging – activates system logging. • Low Capacity Notification Enabled – activates low capacity notification. This works in conjunction with the Allowed Capacity before Email Notification and System Log Buffer Size.
• Allowed Capacity before Email Notification – specify the capacity before an email notification is sent. • System Log Buffer Size – specify the size of the system log buffer. • Remote System Notify Level – specify the type of information, such as none, error, warning, and information, received for remote system logging. 8. In the Auto WAN Detection section, specify the DHCP timeout. 9. Click Apply to save changes. 8.
09/ MONITORING YOUR GATEWAY . 9.0 Gateway Status . 9.1 Advanced Status . 9.2 System Logging . 9.3 Full Status/System wide Monitoring of Connections . 9.4 Traffic Monitoring . 9.5 Bandwidth Monitoring System Monitoring displays system information, including basic settings, system log, key network device parameters and network traffic statistics. GATEWAY STATUS AND ADVANCED STATUS Copyright © 2016 Greenwave Systems. All Rights Reserved.
9.0/ GATEWAY STATUS You can view the basic settings of your Gateway. To view the basic settings: 1. Select System Monitoring in the Main menu. The Router Status page displays. 2. To refresh the page, click Refresh. 3. To continuously refresh the page, click Automatic Refresh On. 9.1/ ADVANCED STATUS You can view the details and status of: • System Logging • Full Status/System wide Monitoring of Connections • Traffic Monitoring • Broadband Monitoring To view the advanced status: 1. Select Advanced Status.
Gateway. In addition, you can view additional logs, such as the security, advanced, firewall, WAN, DHCP, and LAN DHCP. To view the system log: 1. In the Advanced Status page, click the System Logging link. 2. To view a specific type of log event such as Security Log, WAN DHCP Log, etc., click the appropriate link in the menu in the left column. 3. To update the data, click Refresh. 1. In the Advanced Status page, click Full Status/System wide Monitoring of Connections. 2.
Your Gateway continually monitors traffic in the local area network and between the local network and the Internet. You can view up to the second statistical information about data received from and transmitted to the Internet as well as data received from and transmitted to computers in the local network. To view the traffic monitoring data: 1. In the Advanced Status page, select Traffic Monitoring. 2. To refresh the page, click Refresh. 3. To continuously refresh the page, click Automatic Refresh On. 9.
10/ TROUBLE SHOOTING . 10.0 Troubleshooting Tips . 10.1 Frequently Asked Questions This chapter lists solutions for issues that may be encountered while using your Gateway as well as frequently asked questions. TROUBLESHOOTING TIPS Note: The advanced settings should only be configured by experienced network technicians to avoid adversely affecting the operation of your Gateway and your local network. 10.0/ TROUBLESHOOTING TIPS 10.
case, check the WAN cable (Ethernet or Coax) connecting your Gateway to the Internet to make sure it is properly connected on both ends. • Be sure your wireless device is within range of your Wi-Fi Gateway, move it closer to see if your connection improves. • Check your network device’s Wi-Fi settings to be sure your device’s Wi-Fi is on (enabled) and that you have the correct Wi-Fi network and password (if using a Wi-Fi password) as configured on your Gateway.
inadvertently been activated. The common ways to lock access to your Gateway are: • Scheduler - If a schedule has been created that applies to the computer over the connection being used, your Gateway will not accessible during the times set in the schedule. • Access Control - If the access control setting for the computer is set to block the computer, access to your Gateway is denied. To gain access, restore the default settings to your Gateway. 10.
• Confirm that the computer and Gateway are both on the same network segment. If unsure, let the computer get the IP address automatically by initiating the DHCP function, then verify the computer is using an IP address within the default range of 192.168.1.2 through 192.168.1.254. If the computer is not using an IP address within the correct IP range, it will not connect to your Gateway. • Verify the subnet mask address is set to 255.255.255.0. 10.
• Solid red – Unable to connect to the Internet • Fast flash red – Gateway is overheating. Please verify your Gateway is upright and has sufficient ventilation TROUBLESHOOTING TIPS AND FREQUENTLY ASKED QUESTIONS Wireless Light • Solid white – Wi-Fi is on Additional Functions when pressing WPS button: • Slow flash white – When the WPS button is pressed, the Wireless Light slowly flashes white, while waiting for a WPS device to connect. This can require up to two minutes.
• Unlit – Indicates no Ethernet link • Solid green – Indicates a network link • Fast flash green – Indicates network activity. The traffic can be in either direction. LAN Ethernet – Upper LED • Unlit – Indicates no 1 Gbps link • Solid green – Indicates 1 Gbps link • Fast flash green – Indicates LAN activity. The traffic can be in either direction. LAN Ethernet – Lower LED • Unlit – Indicates no 10/100 Mbps link • Solid green – Indicates 10/100 Mbps link • Fast flash green – Indicates LAN activity.
10.1/ FREQUENTLY ASKED QUESTIONS 10.1a/ I’VE RUN OUT OF ETHERNET PORTS ON MY GATEWAY. HOW DO I ADD MORE COMPUTERS OR DEVICES? Plugging in an Ethernet hub or switch expands the number of ports on your Gateway. • Run a straight-through Ethernet cable from the Uplink port of the new hub to the Gateway. Use a crossover cable if there is no Uplink port/switch on your hub, use a crossover cable. • Remove an existing device from the yellow Ethernet port on your Gateway and use that port. 10.
WIRELESS OPTION IS ACTIVATED? Yes, with the unique WPA2 (Wi-Fi Protected Access II) key that is printed on the sticker on the side of your Gateway. 10.1e/ WHICH CONNECTION SPEEDS DOES MY GATEWAY SUPPORT? The Ethernet WAN Internet connection supports 10/100/1000 Mbps. The LAN Ethernet connections support 10/100/1000 Mbps. The 802.11ac wireless connection supports up to 1300 Mbps and the 802.11n supports up to 450 Mbps, depending on signal quality. The Coax (MoCA 2.0) connection supports 700 Mbps. 10.
higher degree of signal loss than those made of wood, plaster, or glass. 10.1i/ HOW DO I LOCATE THE IP ADDRESS THAT MY COMPUTER IS USING? In Windows 7, click the Windows button and select Control Panel, then click View Network Status and Tasks. In the next window, click Local Area Connection. In the Local Area Network Connection Status window, click Details. On Mac OS X, open System Preferences and click the Network icon. The IP address displays near the top of the screen. 10.
10.1m/ I HAVE A FTP OR WEB SERVER ON MY NETWORK. HOW CAN I MAKE IT AVAILABLE TO USERS ON THE INTERNET? For a web server, enable port forwarding for port 80 to the IP address of the server. Also, set up the web server to receive that port. Configuring the server to use a static IP address is recommended. For a FTP server, enable port forwarding for port 21 to the IP address of the server. Also, set up the web server to receive that port. Configuring the server to use a static IP address is recommended.
11/ SPECIFICATIONS 11.0 General Specifications 11.1 LED Indicators 11.2 Environmental Parameters GENERAL SPECIFICATIONS The specifications for your FiOS Gateway are as follows. This includes standards, cabling types and environmental parameters. Note: The specifications listed in this chapter are subject to change without notice. 11.0/ GENERAL SPECIFICATIONS Model Number: Model: FiOS-G1100 IEEE 802.3x, 802.3u IEEE 802.11b/g/n/ac Copyright © 2016 Greenwave Systems. All Rights Reserved.
IP versions 4 and 6 MoCA WAN: 1350 – 1675 MHz and 975 - 1025 MHz MoCA LAN: 1125 – 1225 MHz Wired WAN Ethernet: 10/100/1000 Mbps auto-sensing Wired LAN Ethernet: 10/100/1000 Mbps auto-sensing GENERAL SPECIFICATIONS Cabling Type: Firewall: 11.1/ LED INDICATORS Front Panel: Rear Panel: Wireless LAN: 802.11b – up to 11 Mbps 802.11g – up to 54 Mbps 802.11n – up to 450 Mbps 802.
11.2/ ENVIRONMENTAL PARAMETERS DIMENSIONS AND WEIGHT Frontier FiOS Gateway (unit only) Size: 3.63” width x 9.56” height x 8.50” depth Weight: 1.56 lbs / 0.71 kg Power: Certifications: Operating Temperature: Storage Temperature: Operating Humidity: Storage Humidity: External, 12V DC, 3.0A FCC Part 15, UL 60950-1 10° C to 40° C (50° F to 104° F) -20° C to 85° C (-4° F to 185° F) 8% to 95% (non-condensing) 5% to 100% (noncondensing) Size: 10.16” / 258 mm width x 3.78” / 96 mm height x 10.
12.0/ REGULATORY COMPLIANCE NOTICES 12.0a/ CLASS B EQUIPMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
• This device may not cause harmful interference • This device must accept any interference received, including interference that may cause unwanted operation Note: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 28 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. For operation within the 5.15 ~ 5.
All open source software contained in this product is distributed WITHOUT ANY WARRANTY. All such software is subject to the copyrights of the authors and to the terms of the applicable licenses included in the download. NOTE: This information is provided for those who wish to edit or otherwise change such programs. You do not need a copy of any of such open source software source code to install or operate the device.
