Wifi Smart Thank you for choosing our product. For proper operation, please read and keep this manual carefully.
Content Installation Instruction for WiFi Module .............................................. 1 Download and install App......................................................................... 3 Configuration.................................................................................................. 3 Functions introduction............................................................................... 5 User registration...............................................................................
Operation of Smart Control (Smart Phone, Tablet PC) Installation Instruction for WiFi Module Installation steps of WiFi module Before installation, please confirm whether the purchased WIFI module complies with this unit. WARNING:Installation must be performed by qualified professionals. Otherwise, it may cause personal injury or damage.Do not put through the power before finishing installation. 1. Open the panel of indoor unit as show in the fig and unscrew the screw on the electric box cover.
Operation of Smart Control (Smart Phone, Tablet PC) 4. Place the WiFi module beside the electric box. After confirming the position, please fix the WiFi module with screws. Notice:the position for placing WiFi module may be different for different models; actual position please refer to the actual situation. WiFi module WiFi module WiFi module 5. Neaten the WiFi connection wire, close the electric box cover and then tighten the screws. 6.
Operation of Smart Control (Smart Phone, Tablet PC) Operation Instructions Download and install APP Scan the following QR code (also indicated on package box) with your smart phone and download Wifi Smart. Install the App according to its guidance. When successfully installed, your smart phone homepage will show this icon User of IOS system can search for the wifismart in apple store to download the apple version APP.
Operation of Smart Control (Smart Phone, Tablet PC) gree-a gree-cn gree-dh gree-cn Step 2: Open App and the screen will show the air conditioner that you just connected. Click this air conditioner to enter and realize short-distance control, as shown below. Please refer to "Functions introduction" for specific control methods. NOTE:One AC can be controlled by 4 cell phone in maximun at the same time. 2.
Operation of Smart Control (Smart Phone, Tablet PC) configuration. At this time, “collocating” is displayed on the APP interface. The buzzer in the indoor unit will give out a sound when collocation is succeeded. Functions introduction 1.User registration Purpose: To realize long-distance control Operation instruction: For the first time login, you have to register a new username. If you already have a username, skip the registration step and enter email address and password on the "Login Page" to log in.
Operation of Smart Control (Smart Phone, Tablet PC) (3) Enter your email address. Wait until you receive the verification code. Enter the code and then tap "OK" to log in. (4) If password is forgotten, you can reset the password with your email address. Tap "Forgot password" and enter the page "Forgot password". Input your registered Email account at first. Tap "Get verification code" to get a email verification code. Enter a new password and tap "OK" to log in. 2.
Operation of Smart Control (Smart Phone, Tablet PC) Step 1: Tap and hold "a0b417ac" to enter the page "Edit device". Tap "Image" to select the source of image. Select from "Default images" or "Take photo" or "Choose from photos" and save an image. Step 2: Tap "Name" to change device name, Save it and the new device name will be shown. enable button ''Lock device'' to lock the device other smart phone can’t search the device now. Tap "Temp unit" to change the temperature unit.
Operation of Smart Control (Smart Phone, Tablet PC) (2) Set preset name Step 1: Tap at the top right corner of the homepage "Device". Select "Add preset" and enter the page "Preset edit". Step 2: Choose the time. Tap "Name". As shown in the picture, its name is "baby room". For timer type, select "On". Then select the repeating days. Save the setting of preset name. (3) Set device image Please refer to step 1 in 2(1) 3.
Operation of Smart Control (Smart Phone, Tablet PC) Tap "babyroom" and enter the page of air conditioner control. Tap to turn on the control switch. Tap or to increase or decrease temperature. Tap working mode. Tap to enter the page of fan speed adjustment.
Operation of Smart Control (Smart Phone, Tablet PC) Tap and go around the circle to adjust fan speed. Step 2: Advanced settings Tap to enter advanced settings. You may select "Air", "Dry", "Health", "Light", "Sleep" or "Energy saving". (2) Advanced control functions: Set scene; Preset; Link: Infrared control (only applicable to smart phone with infrared emitter) Set scene: Preset the operation of several smart devices by one tap.
Operation of Smart Control (Smart Phone, Tablet PC) Continue to select the next execution device as instructed above. Tap to set the interval. Tap "Save". Tap the scene picture displayed in "Device" home page to send the command. Then the scene "Back home" will be in execution. You may view the execution condition of the scene. (3) Preset includes single-device preset and multi-device preset Single-device preset: This can preset a certain device to be On/Off at a specific time.
Operation of Smart Control (Smart Phone, Tablet PC) On the homepage "Device", take air conditioner "babyroom" as an example. Tap at the bottom of the page "babyroom". Then you will enter the page "Preset edit". Slide up and down to set the time. If you need to synchronize the time, tap " synchronize". If such "Hint" interface hasn’t appeared, please skip this operation procedure. Tap "Name" to customize the preset name. Preset device can’t be selected and it will default to "babyroom".
Operation of Smart Control (Smart Phone, Tablet PC) Multi-device preset: This can preset multiple devices to execute a command at a specific time. Please refer to the instructions as how to set preset time, name, timer type and repeating days for a single device. Tap "Preset device" to select one or more devices. Then return to the page "Device". (4) Link(This function is applicable to partial of models) Select a master device.
Operation of Smart Control (Smart Phone, Tablet PC) Tap "Temperature" to enter the page "Select temperature parameter". Slide up or down to adjust temperature. Tap "Upper limit" or "Lower limit". Tap "Mode" and "On/Off" to select the status of master device. Then tap "Save". Step 2: Set time parameter for linkage. Tap "Time parameter" to enter the page "Set time". Slide rightwards to turn on the setting time. Tap "Execution time"; Then tap "Start" and "Stop" to set start time and stop time respectively.
Operation of Smart Control (Smart Phone, Tablet PC) Tap the days below "Repeat" to select the repeating days. Then tap "Save". Step 3: Select "Execute command" Tap "Execute command" and enter the page "Select device". Tap the name of device that you want to control. Tap "ON" or "OFF" and then tap "Save" to complete the linkage.
Operation of Smart Control (Smart Phone, Tablet PC) Tap "Save" and then repeat the above steps to set linkage of several scenes. (5) Infrared control (only applicable to smart phone with infrared emitter). Function: Smart phone can be used as a remote controller. Tap at the top right corner of the homepage "Device". Select "Infrared" and enter the page "Remote controller". Tap enter the page of advanced functions.
Operation of Smart Control (Smart Phone, Tablet PC) Tap to turn on the device. Tap to select mode. Tap to adjust fan speed and swing angle. Tap "Health", "Energy saving", "Sleep" etc. to set advanced functions. Tap "Sleep" to enter the page "DIY sleep". Tap the left and right arrows to set sleep time. Tap up and down arrows to adjust temperature at a specific sleep time. 4.
Operation of Smart Control (Smart Phone, Tablet PC) Step 2: Another smart phone to be imported. Tap the model name and wait for the download. (2) Backup: To keep backup of the quick configuration information and unit’s information, including backup to cloud and backup list on the cloud. Backup to cloud Enter the menu page on the left and tap "Backup". Tap "Backup to cloud" and then tap "Yes". Then wait for the data download.
Operation of Smart Control (Smart Phone, Tablet PC) Select "Backup list on the cloud". Then backup records will appear. Tap "Record" to download data and recover data to local unit. (3) Settings User can set vibration, message alerts, server, updates, etc. The server setting here must keep the same as the server setting in "Configuration" mentioned before. Otherwise, remote control will be invalid. (4) Feedback User can feedback suggestions to back-stage management for maintenance and development.
66160000457
Precautions FCC WARNING WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC STATEMENT This device complies with Part 15 of the FCC Rules.
Precautions FCC STATEMENT (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Precautions IC STATEMENT This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Precautions IC STATEMENT antennes utilisées pour cet émetteur doivent être installées et doivent fonctionner à au moins 20 cm de distance des utilisateurs et ne doivent pas être placées près d’autres antennes ou émetteurs ou fonctionner avec ceux-ci. Les installateurs doivent s’assurer qu’une distance de 20 cm sépare l’appareil (à l’exception du combiné) des utilisateurs.