User's Manual

8000mAh Wireless Power Bank
Instruction Manual
2467
User Manual
① Wireless Charging Area
② Nano Rubber
③ On/Off button
④ USB Port
⑤ Micro Port
⑥ Power Capacity Indicator
⑦ Wireless Charging Indicator
⑧ Phone Stand
Features:
Big capacity power bank with phone stand and Nano
rubber.
What’s included:
1* 8000mAh Wireless Power Bank
1* USB Charge Cable
1* User Manual
Tech Specifications
• Power: 5W
• 8000mAh Lithium Polymer Battery
• Input Power: 5V/2A
• USB Output: 5V/2A
• Wireless Output: 5V/1A
• Conversion Rate: >63%
On / Off Button:
• On: Long press
• Off: Double short press
LED Indicators:
• On/Off Button: Press once to view the remaining
power capacity.
Instructions:
1. Charging the power bank.
a. Charge the power bank Fully before initial usage.
b. Insert USB cable into AC wall adapter or computer
USB port to charge the device. LED indicator will flash
BLUE when charging and will stop once fully charged.
2. Charging a mobile device:
a. To charge a mobile device. Insert USB charging
cable to device or place wireless charging enable
device on wireless charge area.
b. Press on/off button, then LED indicators show blue
color. The device will start to charge automatically.
• Note: In order to charge devices, use only the
accessory cable or the cable included with your own
device by the manufacturer.
SAFETY PRECAUTIONS:
WARNING–When using this product, basic precautions
should always be followed, including the following:
1. Read all the instructions before using the product.
2. Charge the power bank fully before initial use. The
unit’s full performance is achieved only after 2 or 3
completed charge and discharge cycles.
3. To reduce the risk of injury, close supervision is
necessary when the product is used near children.
4. Do not expose the device to moisture.
5. Do not use the device in excess of its output rating.
Overload outputs above rating may result in a risk
of fire or injury.
6. Do not use the device if damaged or modified.
7. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or risk
of injury.
8. Do not disassemble the device. Take it to a qualified
service person when service or repair is required.
Incorrect reassembly may result in a risk of fire or injury.
9. Do not expose the device to fire or excessive
temperature. Exposure to fire or temperatures above
212ºF may cause explosion.
10. Have servicing performed by a qualified repair
person using only identical replacement parts.
11. This will ensure that the safety of the product is
maintained.
FCC Warning
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Certification:
FCC ID:2APR2-190956
IEC62368
cTUVus UL2056 standard
Made in China
Any Changes or modifications not expressly approved
by the party responsible for compliance could void the
user's authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuantto
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. During the operation of device a
distance of 15 cm surrounding the device and 20 cm
above the top surface of the device must be
respected.