MZ-10 OPERATING INSTRUCTION Prior to use, please read this manual thoroughly. Keep this manual in a convenient place for quick and easy reference.
Contents • BEFORE USE Thank you for purchasing mz-10 HoTT 2.4GHz Radio System. This system is extremely • Before Use 2P • Support and Service 2P - Customer support 2P - Internet sales site 2P - A/S regulation the web pages referenced below), your hobby dealer, or the Graupner/SJ Service Center. Due 2P to unforeseen changes in production procedures, the information contained in this manual is - Warranty regulation 2P subject to change without notice.
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Graupner/SJ. For up-to-date product literature, visit http://www.openhobby.com and click on the support tab for this product. WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. 7.
8. Mode exchange of throttle stick for Mode 1 and Mode 2 6. ADJUSTBLE STICK LENGTH The control stick is consisted of 2pc of stick levers and it allows you to adjust the control stick’s length as you want. 1. Hold the lever“B”and turn the lever“A” counter clockwise The lock will be released. Lever“A” 2. Turn the lever“B”and adjust the control stick’s length as you want. Turn the lever“A” clockwise, then the lever“A”and“B”are interlocked and fixed.
5 Unscrew the tension spring control bolt in the elevator gimbal of mode 1 transmitter 7 Assemble 2pcs of disassembled leaf spring from the throttle gimbal of mode 1 transmitter into the elevator gimbal and adjust the bolt for the desired control 6 Screw the disassembled bolt from the throttle gimbal of mode 1 transmitter into the elevator gimbal to fix the controller 9 Assemble the centering cam into the throttle gimbal of mode 1 transmitter and set the spring in the center control part and the cent
All Graupner/SJ charge jacks are center-pin negative. This is the opposite of many chargers. 9. WHAT IS HoTT Before using a charger make sure the connector is center-pin negative. This can be done using a voltmeter. Also unlike conventional radio systems that use 8 cells to power the transmitter, the mz-10 HoTT stands for Hopping Sequence Telemetric charger designed for a 4-cell 4.8-volt battery pack when charging the transmitter. Technology, it is Graupner/SJ’s unique telemetry technology in 2.
5. Servo Reversing 7. Delta Wing According to the LED status of each channel, you may check that the direction of servo rotation is in the normal or reverse, LED blinking means that direction of servo rotation is in the normal and LED turning on means that the direction of servo rotation is in the reverse. 1. P ress & hold the DIRECTION button for over 2 sec and then release the button, the transmitter enters reverse mode and the LED of No. 1 channel blinks. 2. Press the MODE button, the LED of No.
- HOLD Function setting LED Description DELTA Green LED On Delta wing function is activated, 2 Aile and V-tail functions are de-activated. 2 AILE Green LED On 2 Aile function is activated, Delta and V-tail functions are de-activated. Enter hold mode by pressing MODE button once from the failsafe mode. The Graupner/SJ logo repeats to blink twice red with twice beep. Press & hold the MODE button for over 2 sec and release the button.
1-2. Pupil setting 12. Stick setting The primary func- off the transmitter, and still the receiver is turned on, and move transmitter’s RF TRAINER SWITCH tions are aileron, elevator, rudder and throttle (or airbrakes). to PUPIL position. Press & hold the MODE button and switch on the transmitter. The Graupner/SJ logo repeats to blink a single red with a single beep, indicating that you set PUPIL Mode. After one beep sound twice, a beep doesn’t sound.
• FIRMWARE UPDATE FCC Information - Graupner /SJ mz-10 Transmitter FCC 47 CFR PART 15C For more information on the latest firmware and the related software, please refer to the download menu on our website www.openhobby.com, www.graupner-sj.com NOTICE: The optional USB adapter is needed to update. FCC Statement 1. This device complies with Part 15 of the FCC Rules.
• FCC radiation exposure statement • ENVIRONNEMENTAL PROTECTION NOTES This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 25 mm between the radiator and your body. This product must not be disposed of with other waste.