EN EN Manual mz-12PRO HoTT 12 channel 2,4 GHz transmitter Copyright © Graupner/SJ GmbH No. S1002.
Index Introduction.............................................................................. 5 Service Centre........................................................................... 5 Intended use............................................................................. 6 Target group.....................................................................................6 Package content........................................................................ 6 Technical data..........................
Battery use timer in the display....................................................20 Use and menu functions......................................................... 20 Four-way keys................................................................................20 Short-Cuts......................................................................................21 Function field in the display.......................................................... 22 Hidden mode.............................................
Introduction Thank you very much for purchasing a Graupner mz-12PRO HoTT transmitter. Read this manual carefully to achieve the best results with your transmitter and first of all to safely control your models. If you experience any trouble during operation, take the instructions to help or ask your dealer or Graupner Service Centre. Notice This manual is composed by two parts. Part 1 is contained in the product's package content. Part 2 can be found in its last version on www.graupner.
Intended use This remote-control system may only be used for the purpose specified by the manufacturer for operation of remote control models without passengers. Any other type of use is impermissible and may damage the system and cause significant property damage and/or personal injury. No warranty or liability is therefore offered for any improper use not covered by these provisions. Read through this entire manual before you attempt to install or use the transmitter.
Technical data Transmitter mz-12PRO HoTT Frequency band Modulation Transmitting power Control functions Temperature range Antenna Operating voltage Power consumption Dimensions Weight 2,4 … 2,4835 GHz FHSS 100 mW EIRP 12 functions of which 4 can be trimmed -10 … +55 °C Integrated antenna 3,4 … 5,5 V approx. 180 mA approx. 190 x 185 x 90 mm approx. 700 g with batteries Note The technical data of the optional receiver are available in the manual included in the receiver package content.
Inform yourself before flying your model on which maximum altitude you can fly in the uncontrolled airspace over the starting position and do not exceed it. Before you start using the remote control model, you have to check the further relevant laws and regulations. These laws you must obey in every case. Pay attention to the possibly different laws of the countries. The insurance is mandatory for all kinds of model operation.
Note During transport protect the model and the transmitter from damages. For your safety by handling the battery CAUTION ! Protect all equipment from dust, dirt, moisture. Only use in dry locations. Do not use any damaged battery. Risk of injury! Any alterations to the battery can cause serious injury. Risk of fire! Batteries may not be heated, burned, short-circuited or charged with excessive current or with reversed polarity.
Special instructions To charge and discharge batteries, only use specifically designed chargers/dischargers with balancer connector. The white connector (cell count + 1 pole) is designed for the connection to a LiPo balancer or a battery charger as a single cell charger with a manual cell balancer. Always charge the battery with the balancer connector. Safety notes for stocking batteries Batteries may only be stored in non completely discharged condition.
Description of the transmitter Control elements on the transmitter 1 16 13 14 2 3 15 12 11 S1002.
2 1 1 1 1 1 1 mz-12PRO 1 12 / 28 3 4 1 5 1 Case screws 2 Battery case cover 3 3,5 mm jack to connect earphones or a DSC cable. 4 Data socket to connect a smart box and to update the transmitter 5 Micro USB port, charge port, update port, joystick function S1002.
Connections and fixtures Attaching the transmitter neck-strap On the upper side of the transmitter there is an eyelet which can be used to hook a neck-strap. Jack socket The port for a 3,5 mm jack is located on the back of the transmitter. Depending on the settings in the menu (OHRH or DSC) this interface can be used as a earphone port or as a DSC cable port. Ear phones port Though this interface both acoustic signals and voice messages are emitted.
Display and touchpad 1 2 3 4 5 6 5.1V 1:23 Stop Flug 11:12 M-01 GRAUBELE 5.4V 1:23h nor mal5.5V N R 7 8 4 9 4 10 1 Model name 2 Memory 1 ... 250 3 Model type display (plane/heli, copter, car, boat) 4 Optical display of the trim position 5 Flight chronometer in min:s (forward/reverse) 6 Flight timer in min:s (forward/reverse) 7 Battery voltage (when a determined threshold is trespassed a warn message is displayed, contemporary a warn signal is emitted).
Commissioning Settings by the first use 1 3 2 1 2 3 Start display Please select RF on/off? ON OFF S1002.PRO_jh_V1 3 Adjusting screw of the brake spring for throttle/brake stick Neutralizing screw Stick self centering force adjust screws After the transmitter is switched on by fixed wing of type "Motor on C1 front/rear" the position of the output 1, so as in hely model the output 6 connected servo, will be verified.
Please select RF on/off? ON OFF During this waiting time you can also switch the RF module off by pushing the or button of the left four-way button which move the black field, in this way the "ON" is shown normally and "OFF" is inverted represented. Control sticks length adjustment Length of both control stick can be adjusted.
Closing step by step: Check if the upper and the lower part of the transmitter housing are correctly coupled and the tiny cables are properly placed. Screw the housing screws in their original position. Connect the battery holder. Neutralizing the control sticks Both control sticks can be set from neutralizing to non-neutralizing. Neutralizing step by step: Locate in the left control stick gimbal the screw surrounded by a white circle in the picture.
General commissioning Binding Model M.Type Servo Control memory Phase adjust. adjust. D/R Expo Tx adjust. C1 curve Wing mix The description of the binding process can be found in the Part 2 of the manual. To use a transmitter you must associate a receiver to the transmitter. This binding process is essential for the use of the model! The precise binding process follow-up is described in the section "Binding" of the Part 2 of the manual and in the related receiver manual.
USB connected 7 PC COM Port Joystick Battery charge As soon as you connect the USB cable to the transmitter a selection menu appears.. Here you can set up the function of the micro USB port. PC COM Port Select this setting for updates with your PC. Joystick Signal volume Back por t DATA sel. DSC output USBjoystick 3 OHRH Telemetr y PPM12 0 ~ 100 For use in a PC with a flight simulator. In this function the PC recognizes the transmitter as a joystick.
Low voltage warning 0:00.0 GRAUBELE S #01 B a t Flug t . m u s0:00.0 t b e«normal re» c h a r K78 g e d !HoTT ! 3.5V x Mx 0.0V 0:22h The transmitter battery voltage should be monitored in the display during operation. In case the voltage drops under a preset threshold, standard setting 3,6 V, an acoustic warning signal is emitted and in the display appears in a window "battery needs charging".
VIEW button Pushing the four-way keys will cause a jump from the transmitter's base screen or from almost any menu position to the "Servo display" menu. TLM button Pushing the TLM key will cause a jump from the transmitter's base screen or from almost any menu position to the telemetry menu. Note In the event the four way keys do not exhibit any functionality immediately after switching the transmitter off and then on again right away, this is not a fault.
Function field in the display Depending on the given menu, certain function fields will appear on the bottom display line. A marked function is activated by pushing the SET key.
1 –100 % 2 0% 3 0% 4 +100 % 5 0% 6 0% 7 0% 8 0% 9 0% 10 0% 11 0% 12 0% STICK CALIBRATION 0 CONTRAST ENGLISH LANGUAGE VOICE DEUTSCH STICK CALI. 0% One after the other, put both sticks into each of their four possible limit positions without exerting force at the limit position and check if the value are between -100% and +100%.
Bar 1 Bar 2 Bar 3 Bar 4 Bar 5 Bar 6 Throttle/brake servo or airbrake right Aileron or left aileron Elevator Rudder Aileron right / free channel Flap (left) / free channel or 2nd elevator servo For helicopter models, the display follows the assignment below: Bar 1 Bar 2 Bar 3 Bar 4 Bar 5 Bar 6 Pitch or roll (2) or nick (2) servo Roll (1) servo Nick (1) servo Yaw servo (gyro) Gyro or Nick (2) Servo Throttle servo or speed controller Pushing the ESC key () of the right four-way keys you turn back to the r
Firmware update The programs and files which are also required for updating the transmitter combined into one software package can be downloaded from www.graupner.de. Download this software package from the Internet, and unpack it on your computer. All other information can be found in internet in the same page where the software package is available. Firmware updates of the transmitter can be performed through the micro USB port on the back side.
In this case as well, as described in the pages before, download a current software package from the Internet and open it on your computer or, if you have already done this, start the program gr_Studio, and follow the information in the section "Restoration" in the instructions provided in the software package. Declaration of conformity S.1002.PRO - mz-12PRO HoTT Graupner/SJ declares that the product is conform to EU norms. EMV 2004/108/EC: EN 301 489-1 V1.9.2 EN 301 489-17 V2.1.
Notes on environmental protection Disposal notes This symbol on the product, user manual or packaging indicates that this product must not be disposed of with other household waste at the end of its life. It must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. The materials are recyclable as marked. By recycling, material reusing or other forms of scrap usage you are making an important contribution to environmental protection.
FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
