User Manual

2
I PrecautionsI.
3
IV.Package included
4
5
6
7
8
《 》Receiver:C series and N series and the sameRECEIVER
Ⅶ.How to use
ALL
1 2 3 4
ON
V.Technical Parameters
ALL
1 2 3 4
ON
Manual instruction
Remote
W ireless
Trigger
I.Features & Functions
Firstly thanks so much for your buying the product,in order to make sure of using
correctly and operating deftly,pleases understand this manual,as well as master how
to use camera and speedlite correctly.You will get usage method and some key points
of this product after reading the munual instruction.
1.Remote trigger(3in1)is using global free channel 2.4GHz,will be popular with many
more countries.
2.FSK modulation system,which makes sure the speed,effective distance and stability
3.Operation distance is up to 100 meters
4.When use CANON & NIKON these professional series cameras to control speedlite,
its sync speed will be up to 1/200 sec,and with wake-up function
5.Much more convenient combination: It is suggested to just buy the single receiver,
so as to only one transmitter can fire several receivers
6.Much more multi-function: It is suggested to buy extri shutter release cables to
control different kinds of cameras,so as to get the same function as remote shutter
release in the course of shooting.
1.This product is electronic equipment accessory,it will cause unnormal phenomenons
on camaras or even cause cameras can not work because of the outisde influences,
but don't worry,this possibility will be very very low.
2.Please don't pull or draw the shutter release cable while connect the camera with cable
3.Please don't touch the metal contact point directly of receiver and transmitter,orelse
it will cause damage
4.Please power off the receiver and transmitter switch,also take out of the batteries when
no need to use for long time.
5.Don't place it understand the high temperature environment,such as into the enclosed
car and control panel.
6.Keep the product dry,don't touch it directly with damp hands,as well as must not leave it into
warter and rains,orelse it will not be used normally,even damaged.
7.Don't use it in the flammable environment,if go against the warning,will cause explosion or
fire disaster.
8.As battery is refered to this product,pls use the battery according to the related disciplines
strictly,orelse will cause property loss and personal security
9.It may cause the flash light self-flash or not flash when the battery capacity isn't enough.
Change a new battery and the phenomenon will disappear.
1.1x Transmitter
2.1x Receiver
3.1x Safe seat for trigger
(1)Hot shoe holder
(2)Test button(shutter release button)
(3)Transmitting indicator
(4)Sync socket(Φ2.5)
《 》TRANSMITTER
4.1x Strobe connecting cable(PE-Φ6.35)
5.1x Strobe connecting cable(PE-Φ3.5)
6.1x Sync cable(Φ2.5x30cm)
Hot shoe holder Receiving indicator
⑽Channel switch ⒀Output socket
⑾Power switch ⒁Battery storage(set with battery 2X1.5V-AAA)
⑼ ⑿ ⒂Battery hatch
Strobe connecting
cable (PE-Φ6.35)
Safe seat for trigger
Sync cable
(Φ2.5x30cm)
Strobe connecting
cable (PE-Φ3.5)
A.Fix the receiver(two ways for fixing)
1.Make use of the hotshoe block:can fix it on the flash holder and the support stand
series with fixing clip
2.Make use of the hotshoe screw:can fix it on the supports and stands with 1/4 screw.
B.Install the transmitter( C series is for Canon,N series is for Nikon)
Install the transmitter on the camera hotshoe holder directly
Triggering Frequency:FSK2.4GHZ
Channel Qty:15+ALL
Sync speed:1/200sec
Operation distance:100m
Transmitter battery:23A-12V
Receiver battery:2x1.5v-AAA
Ⅵ.Fixing&Installation
1.Set up same status of channel switches( )between transmitter and receiver,
different channel status wont control
2.If the transmitter channel switches are set up like this( ),it can control all kinds
of channel status of the receiver in effective area.
3.In order to avoid the signal disturbance from other remote controllers,please set up different
channel status of transmitters and receivers,witch have different channle team.
A.Set up the channel
B.Control the speedlite
1.It is term to fix the receiver after the transmitter has been installed,firstly set up the
battery(2x1.5v-AAA),then turn on the receiver power switch,as well as adjust the channel
switchs.Set up the speedlite on the hotshoe holder after power off the speedlite,then
lock it tightenly,when make sure that all parts have been installed stably,can power
on the speedlite and camera.
2.Half press the camera shutter release button,camera starts to focus.If the speedlite
is on the sleepy status,it will be waked up.
3.After finish the focus action,press the shutter release button of camera completedly,
now the camera start to shoot,and speedlite is fired synchronously.
C. Trigger the studio strobe
1.Plug the studio flash cable into the output socket of the receiver(firstly distinguish the
direction of the cable,then plug)
2.Fixed the receiver well near the strobe,plug the connecting cable pin into sync socket
of the strobe,as well as turn on the strobe.
3.Set up the transmitter on the camera hotshoe holder,the strobe and camera will be
fired synchronously after press the camera shutter release button completedly.
D.Control several flashes
If need to achieve this function,extral receivers and connecting cables will need to
buy,also need to adjust all the receivers and the transmitter channel switches at same
status;Can control several speedlites or several studio strobes as well as speedlites and
studio strobes combination,after start to shoot,all the flashes will be fired synchronously.
1.Fix the speedlite on the receiver hotshoe holder directly.
2.Connect the studio strobe with connecting cable
3.Set up the transmitter on the camera hotshoe holder,press the camera shutter release
butoon completedly,all the studio strobes and speedlites are fired synchronously.
E.Play as remote shutter release
If need to achieve this function,extral shutter release cables will need to buy,
choose different models of cables according to different kinds cameras,these days
shutter release cables encompass all main stream DSLR.
1. Plug one end of the shutter release which isΦ2.5 into the output socket of the
receiver(firstly distinguish the direction of the shtter release cable,then start to plug)
2. Fixed the receiver well on the camera hotshoe holder or near the camera,and plug
the other end of the shutter release cable into the camera shutter socket
3.Power on the camera and receiver switch,at this time, the transmitter is played as
the same function as shutter remote controller.
4.Half press the shutter release button of transmitter,and camera starts to fucus;Press
the shutter release button completedly,the camera starts to shoot.
NOTES:Don't touch the transmitter metal point to avoid wrong action
If has pressed the shutter release button of transmitter completedly,camera still can not
start shooting,please check if the camera lens have been set up as A(auto model)most of
the cameras can not start shooting even receive the shooting signal,if it has not found
the focus point.Now need to change the focus model of camera lens into M(manul model).
F.Use the trigger to operate the camera shutter&trigger the studio flash
(To achieve the function,2pcs 3in1 remote trigger are needed)
1.Set the transmitter(I)and receiver(I)which is used to control camera shutter to the same channel
status.
Then connect the receiver(I)and camera socket with the shutter release cable.
2.Set the transmitter(II)and receiver(II)which is used to trigger flash to the same channel status;
※Fix the transmitter(II)on the camera hot shoe,and fix the receiver(II)to the flash with connecting
cable.
3.Turn on all the power switch,then use the transmitter(I)to control the camera shooting operation
remotely,also flash will be fired synchronously
High voltage triggered speedlite must not be set on the hotshoe of the transmitter
⑴
⑵⑶
⑷
(5)
(6)
(7)
(8)
For Canon For Nikon
C Series N Series
For Canon For Nikon
C Series N Series
⑼
⑽
⑾
⑿
⒀
PSL-16C PSL-16N PSL-16R
With wake-up
As the product update continuously, there maybe some differences between different batch,
all in kind prevail. Please note.
(5)Transmitter power switch
(6)Hot shoe block
(7)Channel switch
(8)Battey hatch(23A-12V battery inside)
⒁
⒂
4
Ⅲ.FCC Statement
1.FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐ Consult the dealer or an experienced radio/TV technician for help.
2.FCC Radiation Exposure Statement
The antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must be located for operating in
conjunction with any other antenna or transmitter.