VOL CH ultra clear™ vibe Baby Monitor OWNER’S MANUAL Keep instructions for future use.
WARNING Failure to follow these warnings and the assembly instructions could result in serious injury or death. This device is designed only to monitor the sounds of your child. It will not alert you to your child’s silent activities. When using the monitor, you must still provide the supervision necessary for the continued safety of your child. This product is not designed or intended for use as a medical monitor.
• DO NOT place unit near water and moisture. Do not use the Nursery Unit outdoors. Do not use the Nursery Unit near possible wet areas, such as a bathtub, shower, wash basin, sink, laundry tub, swimming pool, wet basement, etc. • Keep Nursery Unit away from heat sources, such as fireplaces, radiators, stoves, and TVs or other appliances. Heat can damage the case or electrical parts. • DO NOT use the Nursery Unit if: • The adapter cords or plugs have been damaged. • The unit has been exposed to liquids.
WARNING The Manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Product Features Parent Unit (X2) Sound Lights Power Light Power VOL Volume Adjust Channel Vibe CH Antenna VIBE Speaker CH AC Adapter Jack Power Light PD103056A Channel AC Adapter Jack Belt Clip AC Adapter 5 (X2)
C Adapter ack Nursery Unit Antenna CH Channel Power Light AC Adapter Jack Microphone ON/OFF Night Light PD103078A AC Adapter 6
Battery Installation Parent Unit • The batteries must be installed into the Parent Units before the units will be ready for use. Remove the battery door cover on the Parent Units with a key or flat blade screw driver. 1 2 Remove the battery door. 3 Requires 3 -AA (LR06-1.5V) batteries (not included). Place 2-AA (LR06-1.5V) batteries into the lower battery compartment. Note the proper orientation of the batteries. Place 1-AA (LR06-1.5V) battery into the top battery compartment.
4 Place the battery door back on the unit. 5 Insert the 2 battery door tabs into the slots on the back of the Parent Units as shown. 6 Push battery door tab into slot as shown. 7 Make sure battery door is completely closed. • Please remove a dead battery promptly. A dead battery left in the unit may leak, damaging your unit. • Do not attempt to recharge a non-rechargeable battery. • A rechargeable battery CANNOT be recharged by plugging the AC adapter into the Nursery Unit.
Using AC Adapters 1 CH VIBE • To use AC adapters, plug the connector on the cord into the AC adapter jack on the side of the Parent Unit, then plug adapter into a standard wall outlet. 2 CH • To use AC adapters, plug the connector on the cord into the AC adapter jack on side of the Nursery Unit, then plug adapter into a standard wall outlet. • Use ONLY the Graco adapters included with the unit. Do not use these adapters with other equipment under any circumstances.
Using Antenna For best connection rotate the antenna UP when using the Nursery Unit. MAKE sure to lower the antenna whenever the product is not in use for long periods of time or for storage. VOL To Power Units ON/OFF Push the power button UP as shown to turn unit ON, push DOWN to turn OFF. Push the power button as shown to turn Unit ON/OFF.
Selecting Channels CH CH VIBE • In case you are experiencing some interference, the channel on the Nursery Unit can be changed by switching the channel button on the side of the unit. The Parent Units and Nursery Unit must be set to the same channel, either channel “A” or “B” (“X” or “Y”). Night Light • Some models have a night light on the Nursery Unit that will illuminate when the button on the side of the unit is activated. Push the power button as shown to turn night light ON/OFF.
Vibration CH VIBE To activate the Vibe function push button UP to the ON position as shown. Push button DOWN to turn OFF. VOL Volume To adjust the volume push button UP/DOWN. • The Sound Lights on the Parent Units will illuminate as your child (or other objects) make noise near the Nursery Unit. Please note that the Sound Lights and volume control on the Parent Units are independent of each other.
Setting Up the Baby Monitor 1. For optimum operation, it is best to use new batteries in the Parent Unit. 2. Place the Nursery Unit within 10 feet (3 meters) of your baby. Plug an AC adapter into the jack on the side of the Nursery Unit. Plug adapter into a working 120 volt AC outlet. 3. Aim the Nursery Unit toward your baby. Check that there are no walls or large objects that could block sound transmission. 4. Set both the Nursery Unit and the Parent Unit to the same channel, “A” or “B” (“X” or “Y”). 5.
Troubleshooting DO NOT ATTEMPT to modify the unit. Any modifications to the transmitter and/or receiver can void the operator’s authority to operate the equipment. Most problems have a simple solution. First, check that: • Power is turned ON for both units • Both units are plugged in (or fresh batteries are in Parent Unit. • Electrical outlet works • Volume is turned up on Parent Unit • Parent Unit is in range of the Nursery Unit • Both Units are on the same channel.
Notes 15
Replacement Parts Warranty Information (USA) To purchase parts or accessories or for warranty information in the United States, please contact us at the following: Graco Children’s Products 150 Oaklands Blvd. Exton, PA 19341 www.gracobaby.com or 1-800-345-4109 Product Registration (USA) To register your Graco product from within the U.S.A. visit us online at www.gracobaby.com /productregistration We currently do not accept product registrations from those living outside the United States of America.