Safety Guide

ManualsBrandsGOSAFE ManualsElectronicsGPS tracker

Instruction for GAT-1000

Revision History

Date Changes

2019.09.15

Initial Release

2019.12.03

Update parameters regarding

communication item

The document is subject to change without notice.

This document is a confidential document, Gosafe reserves all rights to this document and the

information contained herein. Any individual or organization is strictly prohibited to reproduce,

use or disclose any of the information contained herein to the third party without permission in

any form or by any means, whether electronic or paper, including photocopying and records.

Otherwise, we hold the right to initiate the legal procedures.

Gosafe will not be responsible for any direct, indirect, special or consequential damages

(including financial loss, personal injury and property damage).

Safety Guidelines

This chapter explains how to operate the "GAT1000" product safely.

By reading the following suggestions and requirements, you will effectively avoid dangerous

situations.

You must read this guide carefully and strictly follow it during operation!

The external battery pack of the device needs to be periodically recharged (battery recharging for

every two months to avoid over-discharge) if the external battery pack is not in use for a long

period.

Do not disassemble the device without authorization. The device must be operated and installed

by professionals.

To charge the battery pack, you must use a charger or adapter.

Summary of content (20 pages)

PAGE 1
Instruction for GAT-1000 Revision History Date Changes 2019.09.15 Initial Release 2019.12.03 Update parameters regarding communication item Copyright and Disclaimer The document is subject to change without notice. This document is a confidential document, Gosafe reserves all rights to this document and the information contained herein.
PAGE 2
Instruction for GAT-1000 Table of contents 1. GAT1000 Introduction ..................................................................................................................... 3 2. GAT1000 product parameters .......................................................................................................... 3 3. Product overview............................................................................................................................. 5 3.1 Unpacking ..................
PAGE 3
Instruction for GAT-1000 1. GAT1000 Introduction The GAT1000 device is a powerful GPS positioning tracker that supports remote sensing technology and has both safety and convenience. It is an ultra-low-power, water splash proof product. The device can detect motion, harsh driving behavior, collision and rollover events.         Report on fixed timing, fixed distance, fixed turning angle, events.
PAGE 4
Instruction for GAT-1000 GPS Detector Input / output Serial port Built-in (External type is optional) 72 search channels Ublox M8 engine GNSS / GPS / GLONASS / BEIDOU -162 dBm SBAS 2.
PAGE 5
Instruction for GAT-1000 3. Product overview 3.1 Unpacking Before you start using the device, please check that the following standard accessories are complete. If anything is missing, please contact the supplier.
PAGE 6
Instruction for GAT-1000 3.
PAGE 7
Instruction for GAT-1000 3.
PAGE 8
Instruction for GAT-1000 3.4 Product status identification and indicators GAT1000 provides three LED indicators, which refer to the status of GPS, COMM (wireless network status) and external power.
PAGE 9
Instruction for GAT-1000 4. User Guide 4.1 Disassembly Before disassembly, check if there are screws on the back side of the shell. If there are screws, use a cross screwdriver to loosen the eight screws on the back side of the shell.
PAGE 10
Instruction for GAT-1000 ② Install SIM card Insert the SIM card as shown in the picture below. ③Plug the Battery  If use for the first time, please plug in the battery connector as shown below.
PAGE 11
Instruction for GAT-1000  Plug in the connector as below picture shows ③ Closing the device  Close the shell and tighten the screws
PAGE 12
Instruction for GAT-1000 4.2 Device installation direction The 3D sensor of device can monitor accident and events of harsh driving behavior. The accuracy of 3D sensor is limited by the installation direction. Please follow the instructions given on the sticker pasted on the device. Note: The front side of the shell must be facing upwards as shown in the picture below. If it is placed upside down than the GPS reception will be affected and the device will not be able to get an accurate GEO location. 4.
PAGE 13
Instruction for GAT-1000 4.4 Engine Ignition ON/OFF detection IGN stands for ignition switch, when the ignition input status is off, the device may be configured into a sleep mode. Mode Ignition ON Ignition OFF Voltage > 5.7V <= 5.
PAGE 14
Instruction for GAT-1000 4.5 Digital Input port Detect the input signal level on digital input pins of the device. The input signal level could be at High or Low level. Mode High Level Input Low Level Input Voltage > 5.7V <= 5.
PAGE 15
Instruction for GAT-1000 Action Status input low No Pin number, value is 0-15 Switch from high level to low level ◇ At command AT Command AT+GEM Input? Description Query the level status of input pin 4.6 Analog signal input The device has two analog signal inputs, and the analog multi-channel input can be configured as digital input detection. Channel AD1 AD2 Input voltage range 0-36V 0-36V 4.7 Digital Output ports The device can output periodic digital signals through its output ports.
PAGE 16
Instruction for GAT-1000 Output Reset ; Output Oneshot ; Output Blink 1; Output Blink 4; Output Pulse ; Pin number, value is 0-8 Output low level Pin number, value is 0-8 Output high level for one second then turns low level Pin number, value is 0-8 Flash, 1 time per 1 second Pin number, value is 0-8 Flash, 1 time per 0.25 second bit0-bit3: Times of the pulses, bit4-bit7: define the pin number.
PAGE 17
Instruction for GAT-1000 4.8 Serial port(s) There are three lines for serial communication port (TXD, RXD and the GND). This port can have RS232, TTL, or RS485 level translation. Default speed is 115200 bps for communication. Normally RS232/RS485 levels are used for communication with the external MDT devices while TTL level is required for communication with the computer devices. Any MDT device can send data through device serial port to the backend server. They can also receive commands from the server.
PAGE 18
Instruction for GAT-1000 4.9 1-WIRE Interface: 1 WIRE can be connected to DS18B20 temperature sensor or the iButton to detect temperature or detect which driver is on duty. The device temperature signal can trigger a temperature alarm event, and the iButton signal can trigger an iButton touch event. The device can be connected to eight sensors at a time or one iButton. The cable for the temperature sensor can be 20 meters long.
PAGE 19
Instruction for GAT-1000 AT + GEM OneWire PWR ON AT + GEM OneWire PWR OFF AT + GEM OneWire? AT + GEM DID List AT+ GEM DID Add AT + GEM DID RM AT + GEM DID Eq 1 WIRE power ON 1 WIRE power OFF Query the value on 1WIRE. Temperature value in the temperature mode. iButton ID in the iButton mode. Print contents of driver ID list Add Driver ID to the list Remove Driver ID from the list Match Driver ID from the list 5.
PAGE 20
Instruction for GAT-1000 This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.