Config Guide

340-00072-06
01 02
Wi-Fi Configuration
Option I /Via Browser
Preparation
Configure Wireless Network
Friendly Tips
1. Power Wi-Fi inverter (or Ezlogger Pro WiFi) on;
2. If you are configuring Wi-Fi inverter, make sure the yellow led on front cover is blining;
3. Power Wi-Fi router on;
4. Switch on the Wi-Fi of laptop.
1. Connect Wi-Fi to "Solar-WiFi" or "Solar-WiFi*"
Password: 12345678
(*means the last 8 characters of the inverter serial number)
In the following sections, we will use “Solar-WiFi”
instead "Solar-WiFi" and "Solar-WiFi*"
Brwose website: http//10.10.100.253
2. Enter User name: "admin". Password: "admin"
3. Click "Start Setup"
Note: If “Unauthorization Login” apperas, please refresh the
web browser.
Note: The AP "Solar-WiFi" might disappera after inverter connects to WiFi router. Turn off router or do "WiFi
Reload" operation via button on inverter if you need connect to Solar-WiFi once again.
4. Select Wi-Fi router's SSID and click "Next"
5. Fill in the password for your WiFi network. 6. Click "Complete" and the configuration process completes.
You can modify the Wi-Fi module’s SSID or/and
password in the "Advanced" interface.
SKIP THIS STEP UNLESS IT IS NECESSARY!
http//10.10.100.253
admin
OK CANCEL
Admin(U):
Password:
Remember the password(R)
Firmware verison
MAC address
Wireless AP mode
SSID
IP address
Wireless STA mode
Router SSID
Encryption method
Encryption algorithm
Router Password
1.6.9.38.2.1.38
60:C5:A8:60:33:E1
Enable
Solar-WiFi
10.10.100.253
Disable
WiFi_Burn-in
WAP / WAP2-PSK
AES
WiFi_Burn-in
SSID
WIFI Test
Network name (SSID)
Encryption method
Encryption algorithm
Network name (SSID)
Encryption mod
Encryption algorithm
Password (8 to 63 characters)
Click "Complete", the current configuration will take effect after
restart.
If you still need to configure the other pages of infrmation,
please go to complete your required configuration.
Configuration is completed, you can log on the Management
page to restart device by Click on ‘OK’ button.
Confirm to complete?
WiFi-Test
WPA/WPA2-PSK
AES
WiFi-Test
WPA/WPA2-PSK
TKIP/AES
1245678
DHCP
192.168.78.2
255.255.255.0
192.168.78.1
0.0.0.0
hellogoodwe
show psk
Password (8-63 bytes)
Sec mode
WAP2-PSK
Enc type
AES
Channel
6
RSSI
54%
Device information
Please select your current wireless network:
Go to SEMS Portal (www.semsportal.com) or SEMS Portal APP,
register and create your Power Station.
Add wireless network manually
Access point setting
DHCP setting for STA
Save success!
Wizard
Management
Advanced
Please enter the wireless network password
Cannot join the network, may be caused by:
Help: Wizard will help you to complete setting within one mimute.
Note: When RSSI of the selected WiFi Network is lower than 50%,
the connection may be unstable, please select other available
network or shorten the distance between the device and the
router.
Note: Case sensitive for SSID and password
Please make sure all parameters of wireless network are matched
with router, including password.
Note: config the device’s parameter under the access point mode.
Note: After changing the settings, the device must be restarted.
If your wireless router does not broadcast SSID, please click
“Next” and add a wireless network manually.
router doesn’t exist, or signal is too week, or password is incorrect
The Wi-Fi module parameters please refer to
‘Device information’ column above.
The Wi-Fi module parameters please refer to
‘Device information’ column above.
Please make sure all parameters of wireless network are
matched with the router, including password.
Start Setup
Back Next
Back
Save
Save
Back Complete
Next