CSCF Evaporator Installation Instructions

ManualsBrandsGoodman ManualsEvaporator Coils2.5 to 3 Ton Horizontal Slab Evaporator Coil

Important Safety Instructions

The following symbols and labels are used throughout this

manual to indicate immediate or potential safety hazards. It is

the owner’s and installer’s responsibility to read and comply

with all safety information and instructions accompanying these

symbols. Failure to heed safety information increases the risk

of personal injury, property damage, and/or product damage.

HIGH VOLTAGE!

Failure to do so may cause property

damage, personal injury or death.

Disconnect ALL power before servicing or

installing this unit. Multiple power sources

may be present.

Only personnel that have been trained to install,

adjust, service or repair (hereinafter, “service”) the

equipment specified in this manual should service

the equipment. The manufacturer will not be

responsible for any injury or property damage arising

from improper service or service procedures. If you

service this unit, you assume responsibility for any

injury or property damage which may result. In

addition, in jurisdictions that require one or more

licenses to service the equipment specified in this

manual, only licensed personnel should service the

equipment. Improper installation, adjustment,

servicing or repair of the equipment specified in this

manual, or attempting to install, adjust, service or

repair the equipment specified in this manual without

proper training may result in product damage,

property damage, personal injury or death.

Shipping Inspection

Upon receiving the product, inspect it for damage from ship-

ment. Shipping damage, and subsequent investigation is the

responsibility of the carrier. Verify the model number, specifi-

cations, electrical characteristics, and accessories are cor-

rect prior to installation. The distributor or manufacturer will not

accept claims from dealers for transportation damage or in-

stallation of incorrectly shipped units.

HORIZONTAL COILS

INSTALLATION INSTRUCTIONS

Codes & Regulations

This product is designed and manufactured to comply with

national codes. Installation in accordance with such codes and/

or prevailing local codes/regulations is the responsibility of the

installer. The manufacturer assumes no responsibility for equip-

ment installed in violation of any codes or regulations.

The United States Environmental Protection Agency (EPA)

has issued various regulations regarding the introduc-

tion and disposal of refrigerants. Failure to follow these

regulations may harm the environment and can lead to

the imposition of substantial fines. These regulations may

vary by jurisdiction. A certified technician must perform the

installation and service of this product. Should you have any

questions please contact the local office of the EPA.

Replacement Parts

When reporting shortages or damages, or ordering repair parts,

give the complete product model and serial numbers as stamped

on the product. Replacement parts for this product are avail-

able through your contractor or local distributor. For the loca-

tion of your nearest distributor consult the white business

pages, the yellow page section of the local telephone book or

contact:

HOMEOWNER SUPPORT

GOODMAN MANUFACTURING COMPANY, L.P.

19001 KERMIER ROAD

WALLER, TX 77484

877-254-4729

Pre-Installation Instructions

Carefully read all instructions for the installation prior to install-

ing product. Make sure each step or procedure is understood

and any special considerations are taken into account before

starting installation. Assemble all tools, hardware and sup-

plies needed to complete the installation. Some items may

need to be purchased locally. Make sure everything needed to

install the product is on hand before starting.

IO-283J

02/2018

Summary of content (4 pages)

PAGE 1
HORIZONTAL COILS INSTALLATION INSTRUCTIONS Important Safety Instructions Codes & Regulations The following symbols and labels are used throughout this manual to indicate immediate or potential safety hazards. It is the owner’s and installer’s responsibility to read and comply with all safety information and instructions accompanying these symbols. Failure to heed safety information increases the risk of personal injury, property damage, and/or product damage.
PAGE 2
Application Information to prevent damage to the drain pan connection. An insertion depth between .355 to .485 inches (3-5 turns) should be expected at this torque. If using a copper drain line, solder a short piece of pipe to the connector before installing a drain fitting. DO NOT over torque the 3/4” copper connector to the plastic drain connection. Coil must be installed downstream (discharge air) of the furnace. Allow a minimum of 18" from the furnace outlet to the coil for adequate transition.
PAGE 3
Tee. The manufacturer does not prohibit this type of drain but we also do not recommend it due to the resulting air leakage. Regardless of the condensate drain design used, it is the installer’s responsibility to ensure the condensate drain system is of sufficient design to ensure proper condensate removal from the coil drain pan. PITCH TOWARDS DRAIN All cut ends are to be round, burr free, and cleaned. Any other condition increases the chance of a refrigerant leak.
PAGE 4
Aluminum Indoor Coil Cleaning 9. AFTER THE TAILPIECE HAS COOLED, confirm position of the white Teflon® seal and hand tighten the 13/16" flare nut. (Qualified Servicer Only) This unit is equipped with an aluminum tube evaporator coil. The safest way to clean the evaporator coil is to simply flush the coil with water. This cleaning practice remains as the recommended cleaning method for both copper tube and aluminum tube residential cooling coils.