User's Manual

ManualsBrandsGood Mind Industries ManualsElectronicsIR EXTENDER

LFIRX2

OWNER’S MANUAL

by AUDIOVOX by AUDIOVOX

Transmitter (TX): The Transmitter converts the infrared

signals from your remote control into long-range RF (radio

frequency) signals that are sent to the Receiver. The LED

lights when the unit is powered and flashes during signal

transmission. The unit has a built-in antenna.

Receiver (RX): The Receiver converts the RF (radio

frequency) signals from the Transmitter back to the

infrared signals used to control your components. The unit

has a built-in antenna and a jack for an Infrared Extension.

The LED lights when the unit is powered and flashes during

signal transmission. The Receiver Unit can be placed up to

100 feet away from the Transmitter Unit.

Infrared Extension: The Infrared Extension can be used in

situations where the Receiver can not be placed in front of

the component(s) it is controlling. This device consists of 1

Infrared diode connected to a 10 ft. extension wire and plug.

EXTENDER

JACK

12V

100mA

System Contents

Your TERK LFIRX2 Remote Control Extender consists of two units

(Transmitter(TX) Receiver (RX)), an infrared extension, and two AC

adapters.

Summary of content (18 pages)

PAGE 1
LFIRX2 OWNER’S MANUAL by AUDIOVOX System Contents Your TERK LFIRX2 Remote Control Extender consists of two units (Transmitter(TX) Receiver (RX)), an infrared extension, and two AC adapters. Transmitter (TX): The Transmitter converts the infrared signals from your remote control into long-range RF (radio frequency) signals that are sent to the Receiver. The LED lights when the unit is powered and flashes during signal transmission. The unit has a built-in antenna.
PAGE 2
STEP 1: Setting Up the Transmitter LFIRX2 Where to Use: Set up the Transmitter in the room where you wish to use your remote control (example: use in the additional room wired to receive a satellite signal from your primary receiver). How to Install: 1. Plug the Transmitter into a standard electrical outlet. 2. Place the Transmitter on a level, stable Transmitter surface, with its remote sensor facing you.
PAGE 3
STEP 2: Setting Up the Receiver LFIRX2 Where to Use: Use in the room where the AUDIO/VIDEO equipment’s infrared sensor is located. How to Install: 1. Plug the Receiver power cord into a standard electrical outlet. 2. Point the Receiver's blaster window toward the infrared remote sensor(s) on the audio/video component. IMPORTANT: Make sure the Receiver is located within 18 feet of the components you want to control.
PAGE 4
STEP 3 (IF NECESSARY): Setting Up the Infrared Extender LFIRX2 Where to Use: • It is only necessary to use the Infrared Extender when the Receiver cannot be easily placed in front of the equipment. (Example: when the component is located in a closed cabinet.) • Use when you would prefer to conceal the Receiver in a cabinet or behind furniture. How to Use: 1. Plug the Infrared Extender into the EXTENDER JACK on the back of the Receiver. 2.
PAGE 5
LFIRX2 5
PAGE 6
Troubleshooting: LFIRX2 1. Make sure both units are plugged into a standard electrical outlet. 2. If the LED light inside the Transmitter does not flash when the Remote Control is operated: • Make sure you are pointing at the front of the Transmitter (the remote sensor is on the front). • Make sure you are within 18 feet of the front of the Transmitter (depending on the range of your individual remote control, it may be necessary to move closer to the Transmitter).
PAGE 7
LFIRX2 5. Move the Unit that appears not to be working to another location and try it again. 6. Attach the Infrared Extender to the Receiver for situations where there is an obstruction (TV Cabinet, etc.) between the Receiver and the component Notice: Any change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
PAGE 8
For customer service and technical information:: 1.800.290.6650 LFIRX2 IB 01 For Customer Service Visit Our Website At www.terk.com Product Information, Photos, FAQ’s, Owner’s Manuals For customer service and technical information:: 1.800.290.
PAGE 9
Para Servicio al Cliente Visite nuestro sitio web en www.terk.com Para servicio al cliente e información técnica: 1.800.290.
PAGE 10
LFIRX2 4. Si la luz LED en el Transmisor destella cuando usted usa el control remoto, pero el LED en el Receptor no destella: • Extienda totalmente la antena hacia arriba o mueva la antena a una posición diferente para mejorar la recepción. • Cerciórese de que el Transmisor no esté a más de 100 pies (30.5 metros) del Receptor. 5. Mueva la unidad que parece estar defectuosa a otra posición e intente nuevamente. 6.
PAGE 11
Resolución de problemas: LFIRX2 1. Asegúrese que ambas unidades estén enchufadas en un tomacorriente eléctrico estándar. 2. Si la luz LED que está dentro del Transmisor no destella cuando se usa el Control Remoto: • Asegúrese que esté apuntando hacia el frente del Transmisor (el sensor del control remoto está en el frente del Transmisor). • Asegúrese que esté situado a no más de 18 pies (5.
PAGE 12
LFIRX2 5
PAGE 13
PASO 3 (SI ES NECESARIO): Instalación de la Extensión de Infrarrojos LFIRX2 Ubicación de uso: • La Extensión de Infrarrojos sólo se debe usar cuando no se pueda situar fácilmente el Receptor en frente del equipo. (Por ejemplo: cuando el componente está situado en un gabinete cerrado). • Utilice la extensión de infrarrojos cuando usted quiera ocultar el Receptor en un gabinete o detrás de un mueble. Cómo usar: 1.
PAGE 14
LFIRX2 s 00 pie o 1 etros) im áx 0.5 m M (3 PASO 2: Instalación del Receptor Ubicación de uso: Utilice el Receptor en la habitación donde se encuentre el sensor de infrarrojo del equipo de AUDIO/VIDEO. Cómo instalar: 1. Enchufe el cordón de alimentación del Receptor en un tomacorriente eléctrico estándar. 2. Oriente la ventana del repetidor de infrarrojos hacia el sensor(es) del control remoto Receptor infrarrojo en el componente(s) de audio/video.
PAGE 15
PASO 1: Instalación del Transmisor LFIRX2 Ubicación de uso: Instale el Transmisor en la habitación donde usted desee utilizar su control remoto (por ejemplo: utilícelo en la habitación adicional cableada para recibir la señal de satélite de su receptor primario). Cómo instalar: 1. Enchufe el Transmisor en un tomacorriente eléctrico estándar. 2. Coloque el Transmisor en una Transmisor superficie estable y nivelada, con el sensor del control remoto orientado hacia usted.
PAGE 16
LFIRX2 MANUAL DEL PROPIETARIO by AUDIOVOX Contenido del sistema Su Extensor de Control Remoto LFIRX2 TERK consta de dos unidades (Transmisor (TX) Receptor (RX)), una extensión de infrarrojos, y dos adaptadores de CA. Transmisor (TX): El Transmisor convierte las señales infrarrojas provenientes de su control remoto en señales de radiofrecuencia (RF) de largo alcance que se envían al Receptor. El LED se ilumina cuando se enciende la unidad y destella durante la transmisión de la señal.
PAGE 17
Important Information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Important Safety Instructions 1. Some of the following information may not apply to your particular product; however, as with any electronic product, precautions should be observed. during handling and use. 2. Read these instructions. 3. Keep these instructions. 4.
PAGE 18
Información Importante ATENCIÓN RIESGO DE CHOQUE ELÉCTRICO. NO ABRIR. Atención: Para reducir el riesgo de un choque eléctrico, no retire la tapa (ni la parte posterior). No contiene piezas que el usuario pueda reparar. Sólo personal calificado de servicio puede hacer reparaciones. Importantes Instrucciones de Seguridad 1. Alguna de la siguiente información quizá no se aplique a su producto en particular.