Installation Instructions

Pair your remote with your smart shade
②
③
④
⑥
⑤
⑦
⑧
⑨
①
Remote Control
Part
①
Description
LED Light
②
③
Left Channel Select
Up/Open
④ Up tilt/75%position
⑨
Channel setting
⑤ Down/Close
⑥
⑦
Right Channel Select
Down tilt/25% position
⑧ Stop/Horizontal 50% position
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
● This device may not cause harmful interference.
● This device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio/TV technician for help.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
HOMEDEPOT.COM/HUBSPACE
Please contact 1-877-592-5233 for further assistance.
Whilst shade is in pairing mode (or if
upper and lower limits have not yet
been set), short press the [down] button
to have shade close continuously.
Long press the [down] button (for up
to 15 seconds) for the shade to move
down continuously. Shade will stop
when the button is let go of.
③ ④
③
Hold the [Channel setting] button for 4 seconds to complete
defining the lower limit. Note that action must be completed
within 3 minutes or the setting will time out.setting will time
out.
Long press the [Channel setting]+[Up]
buttons together for 4 seconds to enter
setting mode for the upper limit. The
motor will jig and the LED will light up.
①
4s
②
Long press the [Channel setting]+[Up]
buttons together for 4 seconds to enter
setting mode for the upper limit. The
motor will jig and the LED will light up.
4s
Setting upper shade limits
③
Hold the [Channel setting] button for 4 seconds to complete
defining the lower limit. Note that action must be completed
within 3 minutes or the setting will time out
Long press [Channel setting]+[Down]
buttons together for 4 seconds to enter
setting mode for the lower limit. The
motor will jig and the LED will light up.
①
4s
②
Inch the blind by long pressing or short
pressing the [Up] or [Down] button to the
desired lower limit position.
4s
Setting lower shade limits
①
②
①
②
①
Whilst shade is in pairing mode (or if
upper and lower limits have not yet
been set), short press the [up] button
to have shade open continuously.
Long press the [up] button (for up to
15 seconds) for the shade to move up
continuously. Shade will stop when
the button is let go of.
②
Inching Shade Up or Down
for setting upper and lower limits
Long press the motor [Up] [Down] key for 3
seconds, motor will jitter and LED indicator will
long light.
Press the channel setting button on back of the
remote control, shade will jig and motor LED
will flash 4 times, indicating the pairing is
completed. The motor LED will go out.
10s
Long press the motor [up] [Down] key for 3
seconds to enter the learning / pairing state.
Motor will jitter and the LED will be long lit.
Long press motor [up] & [down] button togeth-
er for 10 seconds. Motor will jitter, motor LED
will go out, all existing remote control pairings
will be wiped on motor.
Hold the [channel left selection]+[Stop] button
simultaneously. After the signal has been
received, the motor will shake once and the
motor LED will blink 3 times.
3s
Only applicable for remote control that is already successfully
paired with existing shades. Useful for adjusting the top and
bottom shade limits. On the remote control that has paired
successfully, long press the [channel setting] button of the
remote control for 4 seconds. The motor of the shade will jig,
and the shade LED will begin flashing and shade will be sent
into pairing mode.
4s
Entering Pairing / Setting Mode
Entering Setting Mode
For shades already paired
Removing Existing Pairing
Reversing Roll Direction
only needed for over-the-roll direction shade install
3s
NOTE:
1.Before using remote control, each remote must be paired with motor
2.Each motor can record up to 16 remote control channels.