Product Name : Transmitter Models : TE-310 GOLD APOLLO CO., LTD. Rm 1, 3th F1.,No .77, Secretary. 1 , Hsin Tai Wu .,Rd., Hsi-Chih Hsien, Taiwan, R. O. C. Tel : 886-2-2698-8888 Web site : http\\www.apollo.
VHF UHF Transmitter Models : TE-310 16KEY Transmitter
TE-310 Transmitter is used to page guests or staffs in a limited area, especially suitable for factory, restaurant and hospital. The operation is simple and friendly to keep good communication with your guests and staffs. Attention There are 19 push buttons for your choice. Each button is able to independently page a single person and also available to page more than one person at the same time, as well.
Function \ Location Outlook 9 2 10 3 11 4 12 5 13 6 14 7 15 8 F1 16 F2 F3 TX PWR 12 1.TX (Rad) Transmit LED 2.PWR(Orange) Power LED 1 2 3 4 1. Antenna Connect (BNC 50 ohm) 2. Power Connect (8.4V/1.5A) 3. RS232 D-SUB (FEMALE 9PIN) 4. RJ-11 Telephone Jack To Cancer parer. Function \ Location 1
System Specifications System Specifications 1. Frequency range : 147~170MHz, 450~470MHz. 2. Modulation Type : F S K 3. Channel spacing : 12.5 / 25MHz 4. Output power (ERP): 1W 5. Maximum deviation: +/-4.5KHz 6. Harmonic Radiation : less - 25dBm 7. Frequency stability : 2.5ppm at -10C~60C 8. Output Connect : BNC (F) 9. Current Consumption : Standby : 100mA ; Transmit : 400mA 7. Dimensions : 23.2 (W)*50 (H)*17(D) 8.
INSTRUCT ION FOR OPERATIO N: 1.Activate paging: Press any button among these 50 push buttons, the light will flash and enter active mode, then send the signal out. To repeat paging : In the active mode, it can be programmed to send the same message every 30 sec. or 45 sec, or 60 sec, or 2 minutes, or 5 minutes or continuo v To page more than one person : More than one button can be activated at the same time to page more than one person. w LED Sign Display: It's an option on the software.
2. l buttons ControOperation Stop paging: In the active mode or Time out mode, pressing the same button again to stop paging, at the same time the repeating and the number on the LED sign will be cancelled. 3. "Time out" Message display: Once the option of "Time Out " message display is enable, the button will be flash after being pressed for a certain time, and will also send the message to the assigned location or person as a reminder 4.
Instruction for Flash Light: 2. Stop mode: Re-pressing the button to turn off the light represented " Stop mode ". Under the active mode or "Time Out " mode, to press the button again can also enter stop mode. 3. Time Out mode: After repeating paging for a certain time, the light of button will be flashing, then go to Time out mode, Instruction for Flash Light 1.
Instruction for programming: Instruction for programming 1. Activate screen: to set up basic configurations , such as cap code and frequency from button No. 1 to button No.
Instruction for programming 2. To set up the cap codes and type from button No. F1,F2,F3 . butt Please be sure to click " Canned " first to type the content of message.
3.
3. Configuration Instruction: • BEEP OFF : to enable this option, this button has no beep sound Ž Time Out : to enable this option represent the button has been pressed for a certain time and not been delete yet, the light of button can be flash or send out the message to an assigned location or person as reminder. It can be programmable for 5 min, 10 min, 15 min, 30 min, or disable.
Instruction for programming • TX Repeat time : to set up time-gap for repeating page before Time out , it can be programmable for 30sec retary , 45 sec, 60 sec, 2 min, 5 min or disable • LED Msg, enable : to enable this option, the number you press will be shown on the LED display. ‘ LED SIGN CAPCODE: to set up the cap code of LED sign display ’ Head of LED Sign massage : the title displayed on the LED Sign “ Timeout Msg.
5. Read: please see the above in the main menu of the window to execute the command of "To Flash\Read" to read the data. Instruction for programming 4. Write: please see the above In the main menu of the window to execute the command of " To flash\Write" for programming