English Table Call System User Manual
Contents Intr oduc tion.................................................................................1 Devic e & Specif ic ation........................................................... 2 Tr ansmit t er: Ser vic e Call TB- A 06................................. 2 R ec eiv er: RE-300.............................................................. 4 Oper ation & Set ting.................................................................. 6 Manual Pr ogr amming..................................................
Introduction Introduction TABLE C ALL is an easy, smar t wir eless ser vic e bell with 800 met er c o v er age in diamet er. User s c an manually pr ogr am the t able c all sy st em without using the PC. It helps r est aur ant s t o e xpedit e their t able turno v er and ser vic e ef f icienc y. The sy st em c apacit y is up t o 200 pc s t able c all TB- A 06 with 4 pc s r ec eiv er RE-300 that y ou may inst all f r om a small r est aur ant t o bigger ones, which is v er y f le xible.
Device & Specification Transmitter – TB-A06 (The service bell) The but t on: • Ser vic e c all → Blue LED light on • Canc el the c all → Push again and Blue light o f f LED indic at or • Under Char ging: Red LED on • Bat t er y lo w: Red LED blinking • when push the but t on, under char ging or in bat t er y lo w • Char geable, 10 pc s ma x.
Device & Specification Transmitter – TB-A06 (The service bell) This is a t able c all with one ser vic e but t on. With it s ey e-c at ching LED it obt ains w ait er ’s at t ention at visual onc e it is pushed, meanwhile, sending aler t page t o the r ec eiv er in or der t o get ser vic e in shor t est time. It c omes with “Monit or c all” f unc tion t o k eep r ec eiv er a w ar e o f it s av ailabilit y.
Device & Specification Receiver – RE-300 (The desk receiver) Po w er Sy st em NO.
Device & Specification Receiver – RE-300 (The desk receiver) This is a 50-k ey r ec eiv er that user s c an lay it on r ec eption desk or mount ed on the w all. It notif ies the st af f o f which t able is in need o f ser vic e.
Device & Specification RE-300 Specifications Frequency RX Baud Rate(bps) Channel spacing Paging Sensitivity(dBm) Selectivity (25KHz) Spurious & Image Rejection Frequency Stability Receiver Type 430 ~ 470MHz 1200 12.5KHz / 25KHz -122dBm @1200 >=50dB >=50dBm <= +/- 3ppm Synthesized Frequency Deviation ±2.5KHz / ±4.5KHz Alert Tone SPL Operation Temperature Storage Temperature Power Supply Dimensions (mm) >= 80dB@ 10cm -10º~+60º C -10º to +60ºC DC 9V / 2.
Device & Specification TBA06 Specifications Frequency TX TX output High power Transmission radius Channel spacing Maximum Deviation Baud Rate(bps) Conducted Spurious Emission Frequency Stability Operating power Standby Transmit Operation Temperature Storage Temperature Ni-MH Rechargeable battery Low Battery Alert level Dimensions (mm) Charger 430 ~ 470MHz 10mW 400mm 12.5KHz / 25KHz ±2.5KHz / ±4.5KHz 1200 less - 55dBc < ±1ppm 3.6~4.5V Battery package (3 pcs Ni-MH Rechageable battery 1.2V) < 0.
Operation & Setting 5 f unc tion k e y s f or simple manual set ting: How to do Number + Setting 1 Frequency 2 Beep on / off 3 Waiting Time 4 Erase or Add a TBA06 5 TB-A06 in total Power on During setting, if you heard sharp beep it means setting is void. Please reset RE-300 again if so. Always press “50” as confirmation button Until hearing short “beep” and let go, you will see number “1-10” blue LED light-on. Key in frequency and press “50” until you hear long beeping “b-e-e-p” to save it.
Operation & Setting How to do Number + Power on 1+21 Setting Program pagers During setting, if you heard sharp beep it means setting is void. Please reset RE-300 again if so. Command 1-4, 6: Always press “50” as confirmation button 1. Until you hear short beep and let go, you will see that all blue lights turn on. 2. Place SAP-T programmer on the table call, pressing its “number” then “50” until you hear long beeping “b-e-e-p”. (During programming: the light of number turns out to red) 3.
Manual Programming 1. Pr ess “1 + 21” and turn on po w er t o ent er the pr ogr amming mode. 50 blue LED all turn on shor tly. 2. Inser t the pr ogr ammer kit SAP-T on f ir st TB- A 06 f or pr ogr amming. Pr ess the number r epr esenting the f ir st t able c all, then pr ess 50 until y ou hear long beeping. For e x ample: Pr ess NO# “1”, f ollo w ed by “50” until y ou hear the long beeping. You will see the LED indic at or turn out t o RED which means the number is under pr ogr ammed.
Trouble Shooting Due t o wir eless devic e, the int er f er enc e might happen. Each c all ar e guar ant eed t o r ec eiv e within 15 t o 45 sec onds 1.
Warning • • RISK OF EXPLOSION IF BAT TERY IS REPL A CED BY AN INCORRECT T YPE. DISPOSE OF USED BAT TERIES A CCORDING TO THE INSTRUCTIONS.
Make sure to read this manual before using the machine. Please keep it in hand for future reference.