® HDBaseT HDMI Extender over CAT5e/6/7 with IR - 70m P/N: HDbaseT-Ext G4-0018A
Congratulations for owning a gofanco product. Our products aim to meet all your connectivity needs wherever you go. Have fun with our products! Please read this manual carefully before first use. If you need more information about our products, please visit www.gofanco.com. For technical support, please email us at support@gofanco. com. For drivers/manuals download, please go to http:// www. gofanco.com/download.
Introduction gofanco HDBaseT HDMI Extender over CAT5e/6/7 with IR 70m (part# HDbaseT-Ext) extends HDMI signals over one Cat5e/6/7 cable up to 70m (230ft) with bi-directional IR support.
Layout Note: With PoE technology, only one power adapter is needed to power both the Transmitter and Receiver. HDMI In IR In IR Out Figure 1: Transmitter (TX) - HDMI Device Input • HDMI In: Connect your HDMI source here with an HDMI cable (cable not included) • IR In: Infrared 3.5mm socket. Plug IR Receiver extension cable here. See instructions on page 7. • IR Out: Infrared 3.5mm socket. Plug IR Blaster extension cable here. See instructions on page 7.
• Power Jack: Connect the included 12V DC power adapter here (or the Receiver's power jack) • Power LED: On when the Transmitter is powered • Link LED: On when the Cat5e/6/7 cable is connected/ linked properly between the Transmitter and Receiver • LED Indicator: On when Receiver's HDMI out is connected to an HDMI display and the HDMI signal is outputted • RJ45: Link to the Receiver's RJ45 via a Cat5e/6 cable 1: Power LED 2: Link LED 3: LED Indicator Power Jack RJ45 Figure 3: Receiver (RX) - RJ45 Input
HDMI Out IR In IR Out Figure 4: Receiver (RX) - HDMI Display Output • HDMI Out: Connect to your HDMI display here with an HDMI cable (cable not included) • IR In: Infrared 3.5mm socket. Plug IR Receiver extension cable here. See instructions on page 7. • IR Out: Infrared 3.5mm socket. Plug IR Blaster extension cable here. See instructions on page 7.
• IR Blaster cable: Plug into the Transmitter's or Receiver's IR Out to emit IR signals • IR Receiver cable: Plug into the Receiver's or Transmitter's IR In to receive IR signals Control your media player (such as DVD) at the TV side using the media player's remote controller • Plug the IR Receiver cable to the Receiver's IR In port. • Plug the IR Blaster cable to the Transmitter's IR Out port.
Hardware Installation Note: To achieve optimal performance, a CAT6 or CAT7 cable is recommended. 1. Power off all devices including your HDMI source and display. 2. Connect your HDMI source to the Transmitter's HDMI IN connector with an HDMI cable (not included). 3. Optional: Connect the IR Receiver or Blaster extension cable according to the instructions on page 7. 4. Connect your HDMI display to the Receiver's HDMI OUT connector with an HDMI cable (not included). 5.
Application Extend HDMI signals such as game consoles, DVD players or computers up to 70m (230ft) and supports bi-directional IR.
FAQ & Solutions Q: The HDMI display doesn't display images: A: Check the LED indicators' status to make sure all connections are connected properly. If the status is abnormal, check the followings: 1) Whether the power adapter is connected to the Transmitter (TX) or Receiver (RX) securely. 2) Make sure the Network cable (CAT5e/6/7) is firmly connected between TX and RX. 3) Make sure the HDMI cables are securely connected. - Between the HDMI source and the TX. - Between the HDMI display and the RX.
Blank Page 11
® Thank you for choosing gofanco www.gofanco.