TTL 无线引闪器 TTL Wireless Flash Trigger 深圳市神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd. 地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋 Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 Instruction Manual 邮箱/E-mail: godox@godox.
Contents Foreword Thanks for your purchase of this XProO wireless flash trigger. 22 Foreword Mode Settings This wireless flash trigger is suitable for using Olympus & Panasonic cameras to 23 Warning Magnification Function control Godox flashes with X system e.g. camera flash, outdoor flash, and studio flash.
Warning Names of Parts Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. Always keep this product dry. Do not use in rain or in damp conditions. Keep out of reach of children. Do not use the flash unit in the presence of flammable gas. In certain circumstance, please pay attention to the relevant warnings. Do not leave or store the product if the ambient temperature reads over 50℃.
Battery Names of Parts AA alkaline batteries are recommended. Installing Batteries As shown in the illustration, slide the battery compartment lid of the flash trigger and insert two AA batteries separately. Battery Level Indication Check the battery level indication on the LCD panel to see the remaining battery level during the usage.
Using the Flash Trigger Using the Flash Trigger 1.2 Long press the button to set M M Zoom mm channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”). CH19 SLAVE A 1.3 Turn on the camera flash, press the < > 1/128 wireless setting button and the < > wireless icon and slave unit icon will be Zm/C.Fn ± Gr CH displayed on the LCD panel.
Using the Flash Trigger Using the Flash Trigger 3. As a Wireless Studio Flash Trigger Take GS400II as an example: 3.1 Turn off the camera and mount the transmitter on camera hotshoe. Then, power on the flash trigger and the camera. 3.2 Long press the button to set channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”). 3.3 Connect the studio flash to power source and power it on.
Setting the Flash Trigger Setting the Flash Trigger Wireless ID Settings Power Switch Slide the Power Switch to ON, and the device is on and status indicator lamp will not reveal. Note: In order to avoid power consumption, turn off the transmitter when not in use. Change the wireless channels and wireless ID to avoid interference for it can only be triggered after the wireless IDs and channels of the master unit and the slave unit are set to the same. Press the
Setting the Flash Trigger Setting the Flash Trigger Magnification Function Flash Exposure Compensation Settings Switch between multi-group and one-group mode: choose a group in multi-group mode 1. Multi-group displays in the TTL mode and press the button to magnify it to one-group mode. Then, press the to confirm the setting. Output Value Settings 1. 1.2 Press button to choose all groups’ FEC value, turn the select dial, and all Multi-group displays in the M mode 1.
Setting the Flash Trigger Setting the Flash Trigger 6. Until all the amounts are set. Or during any value setting, short press the button to exit the setting status. No values will blink. 7. In the multi flash setting submenu, short press the button to return to main ZOOM Value Settings Short press the button and the ZOOM value will be CH1 displayed on the LCD panel.
Setting the Flash Trigger Setting the Flash Trigger Sync Socket Settings SHOOT Function Settings 1. Press the
Setting the Flash Trigger Setting the Flash Trigger C.Fn: Setting Custom Functions Custom Function Function Setting Signs Settings and Description The following table lists the available and unavailable custom functions of this flash. SHOOT One-shoot Custom Function Function Setting Signs Settings and Description STBY ON ON OFF OFF ON ON OFF OFF BEEP STEP Sleep Beeper Power output 1/128 1/256 The minimum output is 1/256 (change in 0.3 step) 1/128 (0.
Compatible Flash Models Compatible Flash Models The relationship of XT wireless system and X1 wireless system: Transmitter Receiver Flash XProO -- Compatible Flash Models Note AD600Pro/AD600 series/AD400Pro XT-16 (Code Switch) ON ON ON ON ON ON ON ON CH01 CH02 CH03 CH04 CH05 CH06 CH07 CH08 ON ON ON ON ON ON ON ON CH09 CH10 CH12 CH13 CH14 CH15 CH16 AD360II series/AD200/ X1 (Display Screen) V860II series/V850II/TT685 series TT600/TT350O XT-16 (Code Switch) QuickerII
Technical Data Technical Data Model XProO Compatible cameras Olympus/Panasonic cameras (TTL autoflash) Model XProO Firmware upgrade Upgrade through the Type-C USB port Memory function Settings will be stored 2 seconds after last operation Support for the cameras that have PC sync socket. Power supply 2*AA batteries and recover after a restart Wireless Flash Flash Exposure Control Transmission range (approx.) 0-100m TTL autoflash TTL Built-in wireless 2.
3. Attentions As the products needs to do firmware upgrade, please refer to instruction manual of the newest electric version as final. 1. 2. 3. Unable to trigger flash or camera shutter. Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the hotshoe mount or connection cable is well connected, or if the flash triggers are set to the correct mode. Camera shoots but does not focus.
FCC Statement A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. B. Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. C.