Product Info

ManualsBrandsGodox ManualsCamera & PhotoThinklite TTL Camera Flash

Conventions used in this Manual

●This manual is based on the assumption that both the camera and

camera flash’s power switches are powered on.

●Reference page numbers are indicated by “p.**”.

●The following alert symbols are used in this manual:

The Caution symbol indicates a warning to prevent shooting problem.

The Note symbol gives supplemental information.

'PSFXPSE

8BSOJOH

Thank you for purchasing this product.

This TT685IIC camera flash applies to Canon EOS series cameras

and is compatible with E-TTL II autoflash. With this E-TTL II

compatible flash, your shooting will become simpler. You can

easily achieve a correct flash exposure even in complex

light-changing environments. This camera flash features:

●Approx. GN60 (m ISO 100, @200mm), 81 steps from 1/1 to 1/128.

●Fully support Canon E-TTL II camera flash. Workable as

Transmitter or Receiver unit in a wireless flash group.

●Use dot-matrix LCD panel to make clear and convenient

operations.

●With built-in 2.4GHz wireless remote system to support

transmitting and receiving.

●Provided multiple functions, include HSS (up to 1/8000s), FEC,

FEB, etc.

●Stable consistency and color temperature with good even

lighting.

●Support with firmware upgrade.

Always keep this product dry. Do not use in rain or in damp

conditions.

Do not disassemble. Should repairs become necessary, this

product must be sent to an authorized maintenance center.

Keep out of reach of children.

Stop using this product if it breaks open due to extrusion, falling

or strong hit. Otherwise, electric shock may occur if you touch

the electronic parts inside it.

Do not fire the flash directly into the eyes (especially those of

babies) within short distances. Otherwise visual impairment

may occur.

Do not use the flash unit in the presence of flammable gases,

chemicals and other similar materials. In certain circumstance,

these materials may be sensitive to the strong light emitting

from this flash unit and fire or electromagnetic interference may

result.

Do not leave or store the flash unit if the ambient temperature

reads over 50℃. Otherwise the electronic parts may be

damaged.

Turn off the flash unit immediately in the event of malfunction.

*3GXQ/< *3GXQ// *3GXQ// * * *

* 3 3

5D Mark III 5D Mark 6D 7D 60D 50D 30D

600D

500D

*

- 25 -

- 26 -

Thinklite TTL Camera Flash

Godox

TT685IIC

Summary of content (14 pages)

PAGE 1
Godox 'PSFXPSE Thinklite TTL Camera Flash TT685IIC 5D Mark III 5D Mark * 3GXQ /< * 3GXQ // 500D * 3 3 6D 7D 60D 50D 30D 600D * 3GXQ // * II * * * Thank you for purchasing this product. This TT685IIC camera flash applies to Canon EOS series cameras and is compatible with E-TTL II autoflash. With this E-TTL II compatible flash, your shooting will become simpler. You can easily achieve a correct flash exposure even in complex light-changing environments.
PAGE 2
/BNF PG 1BSUT $POUFOUT Ύ 31 Foreword 32 Warning 35 Name of Parts ΍ Body Ε Control Panel Dot-matrix LCD Panel LCD Panel in Three Modes Ώ What's in the Box of TT685IIC Kit? ΐ Γ Separately Sold Accessories 40 Attaching to a Camera 40 Power Management 41 Flash Mode — E-TTL Autoflash Α Β Ζ FEC (Flash Exposure Compensation) FEB (Flash Exposure Bracketing) Δ FEL: Flash Exposure Lock High-Speed Sync Second-Curtain Sync 44 M: Manual Flash 45 Multi: Stroboscopic Flash 46 Wireless Flash Sho
PAGE 3
● LCD Panel ● Receiver Unit (RX) (1)E-TTL Autoflash Zoom : zoom display (Page 54) RX Focus length (Page 54) : High-speed sync (Page 43) : Second curtain sync (Page 43) : Automatic : Manual(Page 44) ETTL : E-TTL II : Receiver :Receiver icon CH autoflash ● LCD Panel in Three Modes ● Attached to the Camera Distance indicator display : Flash exposure compensation (Page 41) Effective Flash Range Flash exposure compensation amount ●The display will only show the settings currently applied.
PAGE 4
● Loading and Unloading the Battery 1 2 To unload the battery, hold down the battery and press compartment and push the battery downwardly to take it out. Put 4 batteries in with the correct polarity after opening the battery compartment, then close and push it to the top. "UUBDIJOH UP B $BNFSB 1 2 3 Attach the Camera Flash. ● Rotate the hotshoe fixing buckle to the left and insert the camera flash into the camera's hotshoe. Secure the Camera Flash.
PAGE 5
1 2 3 Press function button 3 < >. The icon < > and the exposure bracketing amount will be highlighted on the LCD panel. Set the flash exposure compensation amount. ● Turn the Select Dial to set the amount. ● “0.3”means 1/3 step, “0.7”means 2/3 step. Press Set Button again to confirm the setting. Then your FEC and FEB settings are displayed on the LCD panel. ● FEB will be cancelled after three photos are taken.
PAGE 6
. .BOVBM 'MBTI .VMUJ 4USPCPTDPQJD 'MBTI The flash output is adjustable from 1/1 full power to 1/256th power in 1/10th stop increments. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output. 1 Press < MODE > button so that < M > is displayed. 2 Turn the Select Dial to choose a desired flash output amount. 2 Press Set Button again to confirm the setting. With stroboscopic flash, a rapid series of flashes is fired.
PAGE 7
.BYJNVN 4USPCPTDPQJD 'MBTIFT Flash output Hz 1 2 3 4 5 6-7 8-9 1/4 8 6 4 3 3 2 2 1/8 14 14 12 10 8 6 5 1/16 30 30 30 20 20 20 10 1/32 60 60 60 50 50 40 30 1/64 90 90 90 80 80 70 60 1/128 100 100 100 100 100 90 80 1/256 100 100 100 100 100 90 80 Flash output Hz 20-50 60-199 10 11 12-14 15-19 1/4 2 2 2 2 2 2 1/8 4 4 4 4 4 4 1/16 8 8 8 8 8 8 1/32 20 20 20 18 16 12 1/64 50 40 40 35 30 20 1/128 70 70 60
PAGE 8
● Shooting with a Different Flash Mode set for Each Group 3. Setting the Communication Channel Ceiling If there are other wireless flash systems nearby, you can change the channel IDs to prevent signal interference. The channel IDs of the Transmitter unit and the Receiver unit(s) must be set to the same. A E-TTL II Manual flash D B Auto external test flash C Manual flash 1 Press
Button to enter C.Fn CH setting. 2 In C.Fn CH, turn the Select Dial to choose channel ID from 1 to 32.
PAGE 9
1 2 CH 3 4 5 6 7 - 41 - Transmitter Unit Setting ●Attach a TT685IIC camera flash on the camera and set it as the Transmitter unit. ●X1T-C can also be used as Transmitter unit. X1T-C can control TT685IIC 's ZOOM value when the ZOOM is adjusted to auto (A) mode. Receiver Unit Setting ●Set wireless controlled TT685IIC as the wireless Receiver Unit. Check the communication channel. ● If the Transmitter unit and Receiver unit(s) are set to a different channel, set them to the same channel.
PAGE 10
7. M: Wireless Flash Shooting with Manual Flash This describes wireless (multiple shooting) using manual flash. You can shoot with a different flash output setting for each Receiver unit (firing group). Set all parameters on the Transmitter unit. 1 2 3 Setting the flash mode to . Setting flash output. ●Press FunctionButton 1/2/3/4. Turn the Select Dial to set the flash output of the groups. Press Set Button to confirm. Taking the picture. ● Each group fires at the set flash ratio.
PAGE 11
In Manual Zoom mode, press the button. ● Turn the Select Dial to change the flash coverage. ● If < > is displayed, the flash coverage will be set automatically. q q If you set the flash coverage manually, make sure it covers the lens focal length so that the picture will not have a dark periphery. Low Battery Warning If the battery power is low, < > will appear and blink on the LCD panel. Please replace the battery immediately.
PAGE 12
LCD LCD contrast ratio - 3~+ 3 7 levels FEB ACL FEB auto cancel ON ON OFF OFF TX Transmitter unit control 1SPUFDUJPO 'VODUJPO OFF ON 1. Press
Button until C.Fn menu is displayed. The “Ver x.x” in the top-right corner refers to the software version. 2. Select the Custom Function No. ● Turn the Select Dial to select the Custom Function No. 3. Change the Setting. ● Press Set Button and the Setting No. blinks. ● Turn the Select Dial to set the desired number.
PAGE 13
Prompts on LCD Panel E1 E2 E3 E9 • Dimensions Meaning A failure occurs on the recycling system so that the flash cannot fire. Please restart the flash unit. If the problem still exists, please send this product to a maintenance center. The system gets excessive heat. Please allow a rest time of 10 minutes. The voltage on two outlets of the flash tube is too high. Please send this product to a maintenance center. There are some errors occurred during the upgrading process.
PAGE 14
'JSNXBSF 6QHSBEF 'JSNXBSF 6QHSBEF ●The USB port is a Type-C USB socket. Type-C USB connection line is applicable. ●As the firmware upgrade needs the support of Godox G3 software, please download and install the "Godox G3 firmware upgrade software" before upgrading. Then, choose the related firmware file. ●As the product needs to do firmware upgrade, please refer to instruction manual of the newest electric version as final. This device complies with part 15 of the FCC Rules.