闪光灯功率遥控触发器 Wireless Power-Control Flash Trigger For Canon 深圳市神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd 地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋 Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 邮箱/E-mail: godox@godox.
目录 前言 感谢您购买XT32C闪光灯功率遥控触发器。 设置发射器 该触发器适用佳能相机控制神牛闪光灯,远程直接控制具备神牛X无线系统的闪光灯(如 02 前言 02 安全须知 电源开关 04 部件 AF对焦辅助灯开关 X无线系统但带有USB无线端口的神牛闪光灯(如V860系列、V850、AD360、QT系列、 机身 频道设置 SK系列等),可以使用XTR-16或者XTR-16S接收器实现功率调节和引闪等控制。信号稳 LCD显示屏 组别设置 定,反应灵敏,方便摄影师灵活布光,满足多种拍摄需求。同时可以连接具有PC接口的相机 电池 功率设置 使用。支持高速闪光同步,最大闪光同步速度达1/8000s*。 安装电池 试闪 *:限制条件——相机的最大快门速度为1/8000s。 低电池电量指示 控制造型灯 使用引闪器 控制声音 使用热靴触发闪光灯 锁定功能 使用PC接口无线触发闪光灯 设置自定义功能 05 06 07 11 注意事项 11 引闪器的保养 12 产品参数 13 兼容相机列表 TT685系列、V860II系列、AD360II
部件 安全须知 请勿在儿童伸手可及之处保管本产品 本产品包含可能引起窒息的零件。如果儿童不小心吞食了零件,请立即送往医院救治。 若发生任何故障,请立即关闭触发器电源 若发现本产品冒烟或发出异味,请立即取出电池并将本产品送至授权的维修中心进行检 查维修,以避免燃烧。若在此情景下继续使用,可导致受伤。 请勿置于高温中 请勿将本产品放置于阳光直射下的封闭车辆内或其他极高温的地方,否则可能导致火灾 或损坏本产品的外壳或内部部件。 机身 LCD显示屏 组别/PC口设置按钮 频道/睡眠设置按钮 TEST触发按键 声音/延时设置按钮 值设定拨盘 造型灯/锁定设置按钮 使用电池的注意事项 操作不当可能导致电池漏液或爆裂,因此在使用本产品时,请注意以下事项,正确使用 STATUS状态指示灯 电池: --红色LED显示 SET设置按钮 只能使用本手册中列出的电池。请勿混用新旧电池或不同类型的电池。 请仔细阅读并遵守由厂商提供的警告或指示。 切勿使电池短路或拆卸电池。 电池仓(背) 切勿将电池投入火中或加热升温。 切勿试图以反方向安装电池。 AF辅助对焦灯开关 当电量用尽时,电池容易漏液。所以为了
部件 使用引闪器 LCD显示屏 A 1. 使用热靴触发闪光灯 B 使用方法: 1.1 关闭相机电源,将发射器放置于相机热靴插座上, B 打开发射器电源开关和相机电源。 1.2 通过“频道设置按钮”选择频道,使发射器与接收端 C 选择的频道一致。 1.3 按下相机快门即可引闪,同时发射器“状态指示 灯”闪亮红色。 D (A)组别 (B)频道 (G)声音符号 E (C)档位值 (H)造型灯符号 F G H (D)锁定符号 I (E)PC输出符号 (F)延时符号 (I)低电量符号 电池 2. 使用PC接口无线触发闪光灯 使用方法: 安装电池 2.1 设置好发射端和接收端的频道和组别。 滑开发射器与接收器背面的电池盒 2.2 发射器端缺省将PC接口作为输入口,控制接收 盖,根据电池盒内的正负极指示, 器端的闪灯进行闪光。 分别装入2节AA电池。 2.3 正常方式按下快门。将使用PC接口信号控制闪 光。 低电池电量指示 2.4 PC接口可以设置为输出口,具体操作:长按 电池电量较低时(2节电池<2.
设置发射器 设置发射器 电源开关 组别设置 把电源开关拨至“ON”即可打开电源, 状态指示 1. 短按< 灯不显示。在没有操作引闪器的情况下, 产品会在 2. 拨动拨盘选择合适的组别值。再次按< 设置时间段(1分钟/3分钟/10分钟/30分钟)进入睡 眠, 按下按键或者半按相机可以唤醒引闪器。 > 按钮,组别值闪烁。 >按 钮,当前组别值被选定。 3. 引闪器共16个组别,可以在0~9、A~F频道之 间切换。调整功率前请务必将发射器和接收器 睡眠时间设置: 长按< >2秒以上, 直至屏幕显 置于相同组别。 示设置界面, 旋转旋钮调整睡眠时间。 注意:长时间不使用时请关闭电源, 以免耗电! 功率设置 1. 旋转拨盘可以调整档位大小。 *由于XT32C可以无线控制神牛的机顶闪光灯、外 AF对焦辅助灯开关 把电源开关拨至“ON”, 允许输出AF对焦光线。 相机无法对焦时, 对焦灯会自动点亮; 对好焦,对焦 灯会自动熄灭。 异,所以在档位显示模式上做了6种模式。客户可 以根据需求选择。 长按按钮2秒以上,直至屏幕显示功率设 置界面,旋转旋钮调节档位模式。 频道设置 1.
设置发射器 设置发射器 设置显示 说明 锁定功能 1/128+0.3(默认) 档位范围: 1/128~1/1; 档位调节: 1/3 1. 长按< 1/128+0.1 档位范围: 1/128~1/1; 档位调节: 1/10 1/256+0.3 档位范围: 1/256~1/1; 档位调节: 1/3 1/256+0.1 档位范围: 1/256~1/1; 档位调节: 1/10 1.0 档位范围: 1.0~7.0; 档位调节: 0.1 5.0 档位范围:5.0~10; 档位调节:0.1 试闪 < >按钮可以锁定当前设置; 再长按 >按钮可以解锁。 设置自定义功能 操作(长按2秒以上) < 1. 按触发按钮,可以测试闪光是否 < 正常。 > 2. 按下触发按键,此时状态指示灯亮 红色,引闪接受器端闪光灯。 3. 发射器端的设置值将同时同步到接收端中。 < 控制造型灯 1. 短按< >按钮可以控制造型灯的开启和关 闭。 控制声音 1.
注意事项 规格参数 1. 如不能正确引闪或拍摄, 请检查电池是否正确安装以及是否打开引闪器电源; 引闪器是否设 置在同一频道; 连接线或热靴口是否已正确牢固连接到位; 功能模式是否设置正确。 2. 如相机出现只能拍摄不能对焦现象, 请检查机身或镜头是否设定为MF手动对焦, 请设置为 型号 XT32C 兼容相机 Canon相机 支持所有具有PC输出口的相机 AF自动对焦。 3. 如您的引闪器受到他人干扰引闪或拍摄, 改变引闪器的频道设置即可。 内置无线 2.4G频率 4.
Contents 兼容相机列表 本机可兼容以下佳能EOS系列的相机型号: 1DX 5D Mark III 5D Mark II 40D 400D Digital 30D 650D 1000D 6D 7D 60D 50D 600D 550D 500D 450D 1100D 此表格仅列举目前已测试的相机型号, 未涵盖所有佳能EOS系列相机。其他相机型 15 Foreword 16 For Your Safety 18 Names of Parts Power Switch of AF Assist Beam Body Channel Settings LCD Panel Group Settings Battery Power Output Settings 19 21 Setting the Transmitter Power Switch 号, 用户可自行测试。 Installing Batteries Test Flash 本公司保留未来修改此表格内容的权利。 Low Battery Level Indication Modelin
For Your Safety Foreword Thanks for your purchase of this XT32C wireless power-control flash trigger. This flash trigger applies to Canon cameras. It can also directly control flashes which have built-in Godox wireless X system (e.g. TT685 series, V860II series, AD360II series, AD600 series, QuickerII series, etc.). As to the flashes which do not have Godox wireless X system but have USB wireless control port (e.g.V860 series, V850, AD360, QT series, SK series, etc.
Names of Parts For Your Safety extremely high temperature. Failure to observe this precaution could result in fire or damage to the casing or internal parts. Body Observe precautions when handling batteries LCD Panel Batteries may leak or explode if improperly handled. Observe the following precautions when handling batteries for use in this device: Use only batteries listed in this manual. Do not use old and new batteries or batteries of different types at the same time.
Names of Parts A LCD Panel Using the Flash Trigger B 1. As a Wireless Flash Trigger through Hot Shoe 1.1 Mount the transmitter on camera hotshoe and turn it on before turning on the camera. 1.2 Set the transmitter and the receiver to the same channel by pressing Channel Setting Button. 1.3 Press the camera shutter button, and the flash will be triggered simultaneously. Status Indicator Lamp of transmitter turns red.
Setting the Transmitter Setting the Transmitter Power Switch Channel Setting Slide the Power Switch to ON, and the device is on and Status Indicator Lamp will not blink. When in idle use, the flash trigger will enter sleep mode after a period of time (set as 1 minute/3 minutes/ 10 minutes/30 minutes). Press any button or half press the camera can wake it up. 1. Short press the < > Button until the channel amount blinks. 2. Turn the Select Dial to choose the appropriate channel.
Setting the Transmitter Setting the Transmitter Power Output Settings Test Flash 1. Turn the Select Dial to adjust the power output level. 1. Press the Trigger Button to see the whether flash will fire normally or not. 2. Fully press the Trigger Button, and the Status Indicator Lamp turns red and the flash on the receive end can be triggered. 3. The settings on the transmitter end will synchronize to the receiver end at the same time.
Setting the Transmitter Setting Custom Functions Operation Display Settings and Description (Long press the button over 2 seconds) < < < > > SL > 00 OFF 1~100 Synchronization delay N*100 us 01 Enter sleep mode after 1 minute of idle use 03 Enter sleep mode after 3 minutes of idle use 10 Enter sleep mode after 10 minutes of idle use 30 Enter sleep mode after 30 minutes of idle use OF Do not enter sleep mode IN PC Sync socket connect with camera OU PC sync socket connects wit
Compatible Camera Models Technical Data This flash trigger can be used on the following Canon EOS series camera models: Model XT32C Compatible Cameras Canon cameras 1DX Support for the cameras that have PC sync socket. 40D Built-in remote system 2.