User's Manual

ManualsBrandsGODOX PHOTO EQUIPMENT ManualsElectronicsTTL Wireless Flash Trigger(TX)

-13 -

Contents

15 Foreword

15 For Your Safety

17 Names of Parts

Body

LCD Panel Accessories

19 Battery Installing

Batteries

Low Battery Level Indication

20 Using the Flash Trigger

As a Wireless Studio Flash Trigger

As a Wireless Speedlite Trigger

As a Wired Shutter Release

As a Wireless Studio Flash Trigger or Speedlite

Trigger with PC Sync Socket

21 Setting the Transmitter

Power Switch

Power Switch of AF Assist Beam Channel

Settings Mode Settings Current Group Settings

Group Settings Test Flash

Setting GR Grouping Mode Automatically Enter

Power Saving Mode C.Fn: Setting Custom Functions

Wireless Shutter Release Mode Setting the Camera 25

Setting the Receiver

Channel Settings Group Settings

Automatically Enter Power Saving Mode

27 Attentions

27 Caring for Flash Trigger

28 Technical Data

Summary of content (9 pages)

PAGE 1
Contents 15 15 17 Foreword For Your Safety Names of Parts Body LCD Panel Accessories 19 Battery Installing Batteries Low Battery Level Indication 20 Using the Flash Trigger As a Wireless Studio Flash Trigger As a Wireless Speedlite Trigger As a Wired Shutter Release As a Wireless Studio Flash Trigger or Speedlite Trigger with PC Sync Socket 21 Setting the Transmitter Power Switch Power Switch of AF Assist Beam Channel Settings Mode Settings Current Group Settings Group Settings Test Flash Setting GR Groupi
PAGE 2
Foreword For Your Safety Thanks for your purchase of this X1C TTL wireless flash trigger. This TTL wireless flash trigger can be used with a transmitter and one or more receivers for studio flash, speedlite, and camera shutter. Featuring multi-channel triggering, stable signal transmission, and sensitive reaction, it gives photographers unparalleled flexibility and control over their strobist setups.
PAGE 3
Names of Parts Names of Parts • Body Transmitter TEST Trigger Button Receiver TEST Trigger Button --Half Press --Fully Press Battery Compartment AF Assist Beam Switch --ON(AF Assist Beam outputs) --OFF(AF Assist Beam do not output) Battery Compartment Micro USB Port Power Switch --ON (Power On) --OFF (Power Off) PC Sync Socket Hot Shoe Speedlite Connection Status Indicator Lamp --LED Red Color Lamp Power Micro USB Port Switch --ON (Power On) --OFF (Power Off) 2.
PAGE 4
Names of Parts Using the Flash Trigger • Accessories I.Remote Cable(C1, C3) Cable The flash trigger features the following functions: 2.Sync 3.Sync Adapter Battery • Installing Batteries As shown in the illustration, slide the battery compartment lid of the transmitter and receiver and insert two AA batteries (sold separately) separately. • Low Battery Indication When the battery power (2 AA batteries <2.0V) gets low, Status Indicator Lamp blinks quickly (blink cycle=0.5s).
PAGE 5
Setting the Transmitter Using the Flash Trigger 4. As a Wireless Studio Flash Trigger or Speedlite Trigger with PC Sync Socket 4.1 The connection method of the receiver can be found in As a Wireless Studio Flash Trigger and As a Wireless Speedlite Trigger section. 4.2 The transmitter will control the flash on the receiver end to fire via using PC Sync Socket as input by default. 4.3 Press the camera shutter and use the PC Sync Socket’s signal to control the flash. 4.
PAGE 6
Setting the Transmitter group is in the TTL mode, all the other groups which are in the M mode will change their FEC amount simultaneously. The FEC amount is changeable from -3 to 3 in 0.3 stop increments, until one of the group’s setting turns to the maximum(3) or the minimum(-3). If the current group is in the -- mode (flash off), the amounts will not change. 4. Short press the Button again to confirm the setting. • Test Flash Setting the Transmitter • Automatically Enter Power Saving Mode 1.
PAGE 7
Setting the Receiver Setting the Transmitter • Wireless Shutter Release Mode • Group Settings Half press the Trigger Button to focus. Fully press the Trigger Button, and the Status Indicator Lamp turns red. Now camera is ready to shoot. When releasing the button, the Status Indicator Lamp turns off. 1. 2. • Setting the Camera Use the External Flash Function on the camera to do the setting. Note: 1. GR mode can only be used normally when attaching to the CANON EOS cameras that issued 3.
PAGE 8
Attentions Technical Data 1. Unable to trigger flash or camera shutter. Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the hotshoe mount or connection cable is well connected, or if the flash triggers are set to the correct mode. 2. Camera shoots but does not focus. Check if the focus mode of the camera or lens is set to MF. If so, set it to AF. 3. Signal disturbance or shooting interference.
PAGE 9
FCC warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.