User's Manual

ManualsBrandsGODOX PHOTO EQUIPMENT ManualsElectronics2.4G Flash Remote Control(TX)

Foreword

Thank you for purchasing this Godox product!

This product adopts 2.4 GHz wireless remote system and features single-channel triggering, stable signal transmission, and sensitive

reaction. Composed of transmitter and receiver, this product can function as a remote studio trigger, a speedlite trigger and a camera

shutter release. This product is compatible with all brands of studio flash, outdoor flash, and camera flash. It can work with almost any

camera brands such as Canon, Nikon, Sony, Pentax, etc by changing the camera remote cable. We provide different models of camera

remote cables. Based on the models of camera remote cables we include in the package, this product is divided into 3 models: for

Canon, for Nikon, and for Sony.

Contents

Foreword

For Your Safety

Parts

♦ Body

♦ Accessories

Battery

♦ Installing Batteries

♦ Replacing Batteries

Connecting to Camera/Flash/Light Stand

Function Switch

Channel Settings

Using the Remote Control

♦ Wirelessly Triggering Studio Flash

♦ Wirelessly Triggering Speedlite

♦ Wirelessly Controlling Shutter Release

Technical Data

Models of Camera Remote Cable

Troubleshooting

Maintenance

For your safety

To prevent damage to your product or injury to you orto others,

read the following safety precautions in their entirety before

using this product. Keep these safety instructions where all

those who use this equipment will read them.

Failureto observe the precautions listed in this section could

result in damage to the product.

The following icon indicates warnings that should be read

before using this device in case of possible damage or injury.

▲ Do not disassemble or modify

Failure to observe this precaution could result in electric shock

or product malfunction. Should the product break open as the

result of a fall or other accident, remove the batteries and take

the product to an authorized maintenance center.

▲ Keep dry

Do not handle with wet hands, immerse in water, or expose to

rain. Failure to observe this precaution could result in fire or

electric shock.

▲ Do not use around flammable gases

Failure to observe this precaution could result in

explosion orfire.

▲ Keep out of reach of children

This device contains small parts which may pose a choking

hazard. Consult a physician immediately if a child swallows

any part ofthis device.

▲ Turn off immediately in the event of malfunction Should

smoke or an unusual smell come from this device, remove the

batteries immediately and take the device to an authorized

maintenance center, taking care to avoid burning. Injuries

could occur if it is further used.

A Do not expose to high temperature

Do not leave the device in a closed vehicle in the sun or in

other areas subject to extremely high temperatures. Failure to

observe this precaution could result in fire or damage to the

casing or internal parts.

Summary of content (8 pages)

PAGE 1
Foreword For your safety Thank you for purchasing this Godox product! This product adopts 2.4 GHz wireless remote system and features single-channel triggering, stable signal transmission, and sensitive reaction. Composed of transmitter and receiver, this product can function as a remote studio trigger, a speedlite trigger and a camera shutter release. This product is compatible with all brands of studio flash, outdoor flash, and camera flash.
PAGE 2
A Observe precautionwhen handling batteries Batteries may leak or explode if improperly handled. Observe the following precautions when handling batteries for use in this device: • Use only batteries listed in this manual. Do not mix new and old batteries. Neither use batteries of different brand. • Read and follow all warnings and instructions provided by the battery manufacturer. • Batteries cannot be short-circuited ordisassembled. • Do not put batteries into a fire or apply direct heat to them.
PAGE 3
• Accessories 1. Camera Remote Cable 2. Flash Sync Cable 3. PC Sync Cord 4. Sync Adapter Compartment. * Replacing Batteries Low battery powerwill result in no case occurs, replace new good batteries as soon as possible. 1. Power the camera off and disconnect it from this product. 2. Take out the batteries and insert new good ones. • Mounting the receiver on a light stand The receiver has a 1/4^ Mounting Bracket Hole (16) atthe bottom. Therefore, the receiver can be directly mounted on a light stand.
PAGE 4
Using the Remote Control ■ The device features the following functions: Wirelessly Triggering Studio Flash Wirelessly Triggering Speedlite Wirelessly Controlling Shutter Release (normal shooting, longexposure shooting and delay shooting) ■ Wirelessly Triggering a Studio Flash 1. Connection Turn offthe camera. Mount the transmitter on a camera and turn on the camera. Turn offthe studio flash.
PAGE 5
transmit the auto-focus signal and the Transmitter Indicator Lamp turns yellow. Fully press the Triggering Button to transmit the shooting signal and its LED light turns red. Afterthe receiver gets the auto focus signal from the transmitter, its LED light turns yellow. After getting the shooting signal from the transmitter, the receiver LED light turns red. 2.2 Long-exposure setting (with camera setto "bulb" mode) 2.2.
PAGE 6
Models of Camera Remote Cable Cable Models C3 N1 N3 Cable Models Compatible Camera Brands and Models c Canon EOS 1100D(RebelT3),1000D(RebelXS),700D, 650D(T4i),600D(RebelT3i),60Da,60D,550D(Rebel T2i),500D(RebelT1i),450D(RebelXSi),100D Pentax K200,K110DSuper ， K110D,K100D,K20D,K10D,K- 7, K-5, Kr, Kx, *istDS2, *istDS, *istD, *ist, MZ-6, MZ-L d Compatible Camera Brands and Models Canon EOS 1D Mark IV,1D(s) Mark lll,1DMark III, 5D Mark III, 5DMarkll,1D(s)Markll,1DMarkll(N),1DMarkll, 50D,40D,30D,20D,10D
PAGE 7
Troubleshooting 1. Your camera has no hot shoe. —^*^Use the included PC Sync Cord to connect the camera and the remote control. 2. Unable to triggerthe flash or camera shutter. —^*^Make sure batteries are well installed. —^*^Make sure the transmitter and the receiver are both powered on. >*Make sure the transmitter and the receiver are set to the same channel. •—**Make sure the hot shoe or cables are securely connected.
PAGE 8
FCC warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.