Parts List

ManualsBrandsGODOX PHOTO EQUIPMENT ManualsCamera & PhotoTTL Li-ion Round Head Camera Flash

Always keep this product dry. Do not use in rain or in damp

conditions.

Do not disassemble. Should repairs become necessary, this

product must be sent to an authorized maintenance center.

Keep out of reach of children.

Stop using this product if it breaks open due to extrusion, falling

or strong hit. Otherwise, electric shock may occur if you touch

the electronic parts inside it.

Do not fire the flash directly into the eyes (especially those of

babies) within short distances. Otherwise visual impairment

may occur.

Do not use the flash unit in the presence of flammable gases,

chemicals and other similar materials. In certain circumstance,

these materials may be sensitive to the strong light emitting

from this flash unit and fire or electromagnetic interference may

result.

Do not leave or store the flash unit if the ambient temperature

reads over 50℃. Otherwise the electronic parts may be

damaged.

Turn off the flash unit immediately in the event of malfunction.

Thank you for purchasing this product.

This V1C camera flash applies to Canon EOS series cameras and is

compatible with E-TTL II autoflash. With this E-TTL II compatible

flash, your shooting will become simpler. You can easily achieve a

correct flash exposure even in complex light-changing environments.

This camera flash features:

● With round flash head to achieve soft, even and more creative light

effects. It has a 2W LED modeling lamp, which can be used off the

camera.

● 76Ws power output at the max step. 81 steps from 1/1 to 1/128.

● 6 max 480Pro 2 00mAh Li-ion Battery- .1.5s recycle- full power pops.

● Fully support Canon E-TTL II camera flash. Workable as Master or

Slave unit in a wireless flash group.

● Use dot-matrix LCD panel to make clear and convenient

operations.

● With built-in 2.4GHz wireless remote system to support

transmitting and receiving.

● Provided multiple functions, include HSS (up to 1/8000s), FEC,

FEB, etc.

● Stable consistency and color temperature with good even lighting.

● Support with firmware upgrade.

Warning

Foreword

- 31 -

- 32 -

Summary of content (16 pages)

PAGE 1
Foreword Warning Thank you for purchasing this product. Always keep this product dry. Do not use in rain or in damp conditions. This V1C camera flash applies to Canon EOS series cameras and is compatible with E-TTL II autoflash. With this E-TTL II compatible Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. flash, your shooting will become simpler. You can easily achieve a Keep out of reach of children.
PAGE 2
Contents 31 Foreword 32 Warning 35 Name of Parts Body Control Panel Dot-matrix LCD Panel LCD Panel in Three Modes What's in the Box of V1C Kit? Separately Sold Accessories 39 Battery 40 LED Modeling Lamp 40 Attaching to a Camera 40 Power Management 41 Flash Mode — E-TTL Autoflash FEC (Flash Exposure Compensation) FEB (Flash Exposure Bracketing) FEL: Flash Exposure Lock High-Speed Sync Second-Curtain Sync 44 M: Manual Flash 45 Multi: Stroboscopic Flash 46 Wireless Flash Shooting: Radio (
PAGE 3
● LCD Panel Name of Parts (1)E-TTL Autoflash Zoom : zoom display (Page 54) : Automatic Focus length (Page 54) : Manual(Page 44) : High-speed sync (Page 43) ETTL : E-TTL II : Second curtain autoflash 01 sync (Page 43) 09 02 : Master unit flash ON Distance indicator display : Master unit 10 04 03 flash OFF : Flash exposure 11 05 06 07 compensation (Page 41) Flash exposure compensation amount 08 ● Body ● The display will only show the settings currently applied.
PAGE 4
● What’s in the Box of V1C Kit? (4) Radio Transmission Shooting ● Master Unit Flash mode 1. Flash Unit 2. Lithium Battery 3. USB Battery Charger 4. USB Line 5. Charger 6. Mini Stand 7. Protection Case 8.
PAGE 5
LED Modeling Lamp Battery ● Features Press the Modeling Lamp Setting button to set the modeling lamp. 1. This flash unit uses Li-ion polymer battery which has long runtime. The available charge-and-discharge times are 500. 2. It is reliably safe. The inner circuit is against overcharge, overdischarge, overcurrent, and short circuit. 3. Take only 3.5 hours to fully charge the battery by using the standard battery charger. Short press the Set Button to turn on or off the modeling lamp.
PAGE 6
C.Fn Disabling Auto Power Off function is recommended when the flash is used off camera. (C.Fn-STBY, Page 55) C.Fn Slave Auto Power Off Timer is set to 60 minutes by default. Another option “30 minutes” is available. (C.FnSv STBY, Page 55) FEB: Flash Exposure Bracketing You can take three flash shots while automatically changing the flash output for each shot from -3 to +3 in 1/3rd stops.
PAGE 7
● If the subject is too far away and underexposure, the < > icon will blink in the viewfinder. Move closer to the subject and try the FE lock again. ● If is not displayed on the LCD panel, FE lock cannot be set. M: Manual Flash The flash output is adjustable from 1/1 full power to 1/256th power in 1/10th stop increments. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output. ● If the subject is too small, FE lock might not be very effective.
PAGE 8
Multi: Stroboscopic Flash With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture a multiple images of a moving subject in a single photograph. You can set the firing frequency (number of flashes per sec. expressed as Hz), the number of flashes, and the flash output. 1 2 Press button so that < MULTI > is displayed. Set the flash frequency and flash times. ● Press the Function Button 2 to select the flash times. Turn the Select Dial to set the number.
PAGE 9
● Shooting with a Different Flash Mode set for Each Group Positioning and Operation Range (Example of wireless flash shooting) ● Autoflash Shooting with One Slave Unit Ceiling A D E-TTL II B Transmission distance is about 100m. Manual flash C Manual flash Manual flash ● Use the supplied mini stand to position the slave unit. ● Before shooting, perform a test flash and test shooting.
PAGE 10
3. Setting the Communication Channel If there are other wireless flash systems nearby, you can change the channel IDs to prevent signal interference. The channel IDs of the master unit and the slave unit(s) must be set to the same. 1 Press
Button to enter C.Fn CH setting. 2 Slave Unit Setting ● Set the other camera flash as the wireless slave Unit. 3 Check the communication channel. ● If the master unit and slave unit(s) are set to a different channel, set them to the same channel.
PAGE 11
Using Automatic Wireless Flash with Multiple Slave Units When stronger flash output or more convenient lighting operation is needed, increase the number of slave units and set it as a single slave unit. To add slave units, use the same steps as setting “automatic wireless flash with a single slave unit”. Any flash group can be set (A/B/C/D/E).
PAGE 12
Other Applications Sync Triggering The Sync Cord Jack is a Φ2.5mm plug. Insert a trigger plug here and the flash will be fired synchronously with the camera shutter. Modeling Flash If the camera has a depth-of-field preview button, pressing it will fire the flash continuously for 1 second. This is called modeling flash. It enables you to see the shadow effects on the subject and the lighting balance. You can fire the modeling flash during wireless or normal flash shooting.
PAGE 13
C.Fn: Setting Custom Functions The following table lists the available and unavailable custom functions of this flash. C.Fn Custom Functions Custom Function Signs Function m/ft Distance indicator Setting No. Settings & Description m m Control with the Camera’s Menu Screen If the camera flash is attached to an EOS camera which has a speedlite control function, the flash can be controlled using the camera’s menu screen. For the menu operation procedure, refer to your camera’s instruction manual.
PAGE 14
Technical Data Protection Function 1. Over-Temperature Protection Model ● To avoid overheating and deteriorating the flash head, do not fire Compatible Cameras Canon EOS cameras (E-TTL II autoflash) Power 76Ws more than 30 continuous flashes in fast succession at 1/1 full power. After 30 continuous flashes, allow a rest time of at least 10 minutes. (1/1 output) Flash Coverage ● If you fire more than 30 continuous flashes and then fire more is shown on the LCD display.
PAGE 15
Troubleshooting Firmware Upgrade If there is a problem, refer to this Troubleshooting Guide. ● The USB port is a Type-C USB socket. Type-C USB connection The Camera Flash does not fire. ● As the firmware upgrade needs the support of Godox G3 line is applicable. ● The camera flash is not attached securely to the camera. →Attach the camera’s mounting foot securely to the camera. ● The electrical contacts of the Camera Flash and camera are dirty. →Clean the contacts.
PAGE 16
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.