USER GUIDE 800.788.5572 GraphicProducts.
Graphic Products®, DuraLabel®, PathFinder®, Toro® and Lobo® are Registered Trademarks of Graphic Products, Inc. © 2015 Graphic Products, Inc.
Before You Begin Safety Warnings Before connecting Bronco to a power outlet, check the voltage of the power source, and ensure that the power switch on the printer is in the OFF position. Only use the included power supply with the Bronco (rated for 24V/2.5A output, model WDS060240). If a replacement is needed, please contact your DuraLabel representative. To avoid electrical shock, DO NOT pour any liquid onto the printer or printer parts.
Contents 1. Getting Started 1.1 Know Your Bronco 1.1.1 Exterior 1.1.2 Connection Panel 1.1.3 Interior – Print Head Carriage Locked 1.1.4 Interior – Print Head Carriage Released 1.2 Loading Supplies 1.2.1 Loading Ribbon 1.2.2 Loading Label Stock 1.3 Initial Setup 1.3.1 Physical Connections 1.3.2 Installing Driver Software 4 5 5 5 5 6 6 7 7 8 8 8 8 2. Using Your Bronco 2.1 Printing and Pausing 2.2 Driver Settings 2.2.1 Size and Orientation 2.2.
1. Getting Started 1.1 Know Your Bronco 1.1.1 EXTERIOR Pause/Feed Button and Indicator Light Lid Release Tabs Cutter Module 1.1.2 CONNECTION PANEL Power Switch Power Supply Connection USB Connection GraphicProducts.com | 800.788.5572 1.
GETTING STARTED 1.1.3 INTERIOR – PRINT HEAD CARRIAGE LOCKED Ribbon Take-Up Holders Carriage Release Tabs Print Head Carriage 1.1.4 INTERIOR – PRINT HEAD CARRIAGE RELEASED Print Head Ribbon Supply Holders Adjustable Supply Guides 6 | 1.1 Know Your Bronco GraphicProducts.com | 800.788.
GETTING STARTED 1.2 Loading Supplies To load your Bronco with supplies, turn the system off using the power switch at the back, near the power cord. Then, press inward at the textured areas on both sides of the system, and raise the hinged cover. The cover will rest at the fully-opened position, requiring about 12 inches of vertical clearance. You need two supplies to print: the printing ribbon, or “ink,” and the label stock, or “vinyl.” 1.2.
GETTING STARTED 1.2.2 LOADING LABEL STOCK Fresh label stock comes in a roll with plastic end caps on each side. The material typically has a glossy print surface on one side, and a disposable paper backing on the other side. When printing, Bronco will feed some of the label stock from its roll and cut off the printed label. 1. If you haven’t already done so, raise the print head carriage by pressing the two green carriage release tabs. 2. Place the roll of label supply onto the supply spindle.
2. Using Your Bronco 2.1 Printing and Pausing To print a label, open or create a label design in your preferred label design program. (For help with the DuraSuite software, see the documentation for that program.) Use the program’s File menu to select Print. In the Print window, select the DuraLabel Bronco as the printer, choose appropriate settings with the Properties or Preferences button, and click Print.
USING YOUR BRONCO 2.2.2 SETTINGS FOR PRE-PRINTED OR DIE-CUT MATERIAL When using supplies that are pre-printed or die-cut, the printer will need to be properly set and calibrated to line up the print on the label stock. There are two parts to this process: setting the driver settings, and calibrating the printer’s sensors. Your Bronco’s driver settings for these types of material are located on the Stock tab of the Printing Preferences window.
USING YOUR BRONCO 2.2.4 DARKNESS Depending on the supplies that you are using, you may need to adjust the Darkness setting to maintain print quality. Most frequently, this comes up when changing from a Premium ribbon to a Chemical-Resistant ribbon, or vice-versa. Specialty ribbons typically require a higher Darkness setting. This option is found as a slider on the Options tab of the Printing Preferences. 2.2.
3. Warranty and Compliance Statements 3.1 5-Year DuraLabel Printer Warranty Graphic Products’ DuraLabel printers are warrantied to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase. Within this period, Graphic Products, Inc. will, at its sole option, repair or replace any components which fail in normal use.
WARRANTY AND COMPLIANCE STATEMENTS 3.2 FCC Compliance Statement for Users in the United States This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
4. Contact Us Graphic Products, Inc. has been a leader in custom labeling, signage, and visual communication solutions since 1970. Our commitment to providing world-class service is at the heart of everything we do. If you have any further questions, or if any problems arise that are not addressed in this User Guide, please let us know. Graphic Products proudly offers free support to all of our customers. Call us at: 800.788.5572 (U.S.A. and Canada only) 1.503.644.
THIS PAGE IS INTENTIONALLY LEFT BLANK
800.788.5572 | DuraLabel.com © 2015 Graphic Products, Inc.
