Digital Radio User's Manual 335100413_RevA
To Users Thank you for purchasing out product! This Manual (contains both analog and digital radios) is designed to make you quickly grasp the use of the device. In order to avoid physical injury or property loss due to improper operation, please read this Manual carefully before using the device. Notice The device meets the requirements of FCC PART 90, PART 97 and PART 15.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and. 2. this device must accept any interference received, including interference that may cause undesired operation. ISEDC RSS warning This product meets the applicable Industry Canada technical specifications. / Le présent matériel est conforme aux specifications techniques applicables d’Industrie Canada.
may cause minor burns when it comes into contact with the skin. ·Do not expose the radio to direct sunlight for a long time or place it near the heating Radio. ·If you wear a portable radio, make sure the antenna is at least 2.5 cm away from your body when the radio is transmitting. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• • Using Tips • • • To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50 % of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). Hold the radio in a vertical position in front of face with the microphone (and the other parts of the radio, including the antenna) at least one inch (2.5 cm) away from the nose.
European Union (EU) Waste of Electrical and Electronic Equipment (WEEE) directive： The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries. EU Frequency Range and the Max. Transmit Power Frequency Range 446.0~446.2MHz The Max. Transmit Power 0.
Using Tips • Les instructions de sensibilisation des utilisateurs doivent accompagner l'appareil lors de leur transfert à d'autres utilisateurs. • N'utilisez pas cet appareil si les exigences opérationnelles décrites ici ne sont pas remplies. Mode d'emploi: • Ne transmet pas plus que le facteur de marche nominal de 50% du temps. Pour transmettre (parler), appuyez sur le bouton Push-ToTalk (PTT). Pour recevoir des appels, relâchez le bouton PTT.
INFORMATION CONCERNING SAR FOR CE Max. SAR Level(s) Measured Limit (W/Kg) 0.164 W/kg 10g Head SAR 0.181 W/kg 10g Body SAR 2.0 INFORMATION CONCERNING SAR FOR FCC Max. SAR Level(s) Reported Limit (W/Kg) 0.85 W/kg 1g Head SAR 8.0 1.
Product Control Antenna Power key LED Indicator Know the Radio Up key PTT key Headset Port Down key USB Port Menu key Programmable key Display Microphone Speaker Charging contacts 8
Display Guide Channel display Signal strength Battery Level icon Volume icon VOX icon DCS Code icon CTCSS Code icon Channel indication Digital mode Analog mode Scan icon Radio Status LED Indication Standby Green Slow Flash Low Battery Red Fast Flash Transmit (TX) Solid Red Receive (RX) Solid Green Programming Mode (Read from Radio) Red Fast Flash Programming Mode (Write to Radio) Red Fast Flash 9 Know the Radio Radio LED Indicators
Battery Installation 1. Use finger tip to pull the latch as shown in picture below to remove battery cover. 2. Put the battery pack into the battery compartment, close the battery cover with snap fit all latches. Ensure the battery cover is fully fix to radio. 熟悉本 机Radio Know the Note: To remove the battery pack, please turn off the radio first. 3. Install the belt clip holder using a coin or screwdriver as shown in the picture.
Belt Clip Installation 1. Align the guide groove of the belt clip to the belt clip holder on the battery cover and install it appropriately. Note: The belt clip can be installed from any direction, clip on the belt, and the radio can rotate 180 degrees. 2.Take out the belt clip to the following angle with belt clip bottom face up, and remove it toward the top. 熟悉本 机Radio Know the Figure 1 Figure 2 Accessory Installation 11 Step 1: Open the accessory connector cover.
Charging Function 1. This device can support charging with charger tray or direct USB charging. During charging, the battery icon flashing on the display; when complete charging, the icon stops scrolling and shows battery full. 熟悉本 机Radio Know the Device charging Charging precautions: USB charging ·Please use the matching charging base of the model for charging. ·When charging the device, it is recommended to turn off the radio first.
·During charging, it is not recommended to transmit the radio. ·The battery pack may slightly heat up during charging, which is a normal phenomenon. Power On/Off To turn on radio, press and hold [Power] key 3 seconds. To turn off radio, press and hold the [Power] key to turn off the radio and prompt tone will be sounded. Check Channel and Battery Level status Volume Control press [+] or [-] key to increase or decrease the volume. the volume is adjustable from level 0 to 10.
and keep the microphone 2.5-5 cm away from the mouth. When transmitting, the radio should be at least 2.5 cm away from the head or body. ·Do not turn on/off the radio repeatedly during use, and adjust the volume to a level suitable for your hearing. ·Before using the radio for communication, please set the transmitter and receiver to the same frequency point. ·For the analog channel that requires intercom, please set the transmitter and receiver to the same sub-audio frequency. ·For digital channel, 1.
the [+] or [-] key to start/stop channel scanning, and the speaker will give a voice prompt "Scan on" or "Scan off".During scanning, the digital radio scans the channels in the list and the current main channel. When any channel in the scan list is transmitting a signal, it will stay on that channel after scanning the signal. If press the [+] key again will skip the current channel and continue scanning.
Voice Control Function (preset by [Program] key) 1. Preset the [Program] key to [VOX On/Off] key through programming software. 2. Press the preset [VOX On/Off] key to turn on/off the voice control function. VOX levels can be preset through programming software: Level 1, Level 2, and Level 3, where Level 3 is the most sensitive. When the radio VOX function is on, the preset VOX level is used. Monitoring mode (preset by [Program] key) 功能 介绍 Features 1.
Program Key 1. Configure the functions of [Program] key through programming software. 2. The [Program] key of analog Mode includes the following functions: VOX On/Off, Monitoring Mode, Sub-audio Frequency On/Off. 3. The [Program] key of digital Mode includes the following functions: High/Low Power Switch, VOX On/Off, Monitoring Mode, One Touch Call, Emergency Alarm, etc. 4. Write the set parameters to the radio and press the corresponding [Program] key to enter the corresponding function.
Squelch Step (SQ) 1. SQ is only valid for analog channels. 2. After SQ is set to 0, the speaker will automatically turn on and be in the monitoring state. 3. The higher the SQ step, the better the noise floor suppression effect. 4. SQ can be configured through programming software only. Radio Name Configuration and Modification 功能 介绍 Features 1. Enter the basic setting interface of programming software to configure or modify the Radio name. 2.
or re-burn it. DTMF Function 1. The DTMF interface of the programming software can configure the DTMF function, such as side tone, duration, interval time, online telegram code, offline telegram code, transmission start sound, transmission end sound, transmission start and end sound. 2. After the transmitter turns on the side tone, when the [PTT] key is pressed to transmit, the transmitter itself will also give DTMF sound; 3. DTMF coded content only supports numbers 0-9, letters: ABCD, and characters: * #.
3. The same encryption template must be configured for transmitter and receiver for normal intercom, otherwise the speech content cannot be heard clearly. 4. The main purpose is to prevent the content of the speech from being monitored by other people at the same frequency. Color Code 1. For digital channels, the color code must be same to call. 2. The color code range of this product can be set: 0-15. Contacts 功能 介绍 Features 1. Contacts are only valid for digital channels. 2.
3. The transmitter's red indicator stays on for a few seconds, and then press the [PTT] key to transmit. 4. The receiver's green indicator stays on for a few seconds, and then it can receive normally. Remote Monitor(private call only) 1. Configure monitor feature through programming software. 2. Press the programmable key to monitor the other party remotely. 3. After successful monitoring, the green indicator will always be on, and the sound around the other party can be clearly monitored. 4.
4. Backlight time can be written directly by programming software. Language Settings 1. Language supports: Chinese and English. 2. Language can be set by programming software. 3. After switching the language, all voice broadcast will be changed to the language. 4. The radio voice announcement is defaulted to English. Optional Accessories Features The main accessories of the Radio are included in the product packaging box. For more information about accessories, please consult your local dealer.
Model Number： Telephone： Post Code： User’s Name： Chop b y Dealer 4.Warranty void if seal broken. 5.1 year guarantee for product, 6 months for charger,battery and antenna . 6.The user can get repairing service from the following ways: a.Go to the shop where you buy the machine b.Our local repairing agent REMARKS: 1.This guarantee card to be kept by the user ,no replenishment if lost. 2.This guarantee card to be filled & chopped by the dealer,or it is invalid. 3.
+
