Digital Radio User's Manual Rev.
To Users Thank you for purchasing our product! This Manual is designed to make you quickly grasp use of this device. In order to avoid physical injury or property loss due to improper operation, please read this Manual carefully before using this device. Notice The device meets the requirements of FCC PART 90, PART 97 and PART 15. Local laws and regulations shall be complied with when setting up or using the equipment, and corresponding qualifications and relevant procedures shall be obtained if necessary.
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ISEDC RSS warning This product meets the applicable Industry Canada technical specifications. / Le présent matériel est conforme aux specifications techniques applicables d’Industrie Canada.
·In vehicles with airbags, do not place the radio in the area where airbag deployment may be involved. ·Please turn off the radio before entering flammable or explosive environment. ·Do not replace or charge the battery in a flammable or explosive environment. ·Please turn off the radio before approaching the blasting area and the detonator area. ·Do not use the radio with damaged antenna. A damaged antenna may cause minor burns when it comes into contact with the skin.
RF Exposure Compliance and Control Guidelines and Operating Instructions 4 Using Tips To control your exposure and ensure compliance with the occupational/ controlled environment exposure limits always adhere to the following procedures. Guidelines: • Do not remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. • Do not use this device if the operational requirements described herein are not met.
• For a list approved accessories please consult your local dealer for information. European Union (EU) Waste of Electrical and Electronic Equipment (WEEE) directive: The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries.
lors de la transmission (en termes de mesure pour la conformité aux normes). • Tenez la radio en position verticale devant le visage avec le microphone (et les autres parties de la radio, y compris l'antenne) à au moins 2,5 cm du nez. Garder la radio à la bonne distance est important car les expositions RF diminuent avec la distance de l'antenne. L'antenne doit être tenue à l'écart des yeux.
User Interface Know the Radio 7
About the Device 1 2 3 4 5 6 Antenna P1 key PTT key P2 key Channel knob Power switch/volume control knob 7 8 9 10 11 12 Alarm key LED indicator Accessory port Speaker Microphone Battery Latch Radio LED Indicators LED Indication Standby Blinking Green Low Battery Transmit (TX) Receive (RX) Programming Mode (Read from Radio) Programming Mode (Write to Radio) 8 Blinking Red Solid Red Solid Green Fast Blinking Red Fast Blinking Red Know the Radio Radio Status
Power On/Off and Volume Control Power on/off: Turn the power switch knob to turn on/off the radio normally. Note: The battery needs to be charged, otherwise the radio cannot be turned on under low power state. Volume control: In standby state, turn the knob clockwise/ counterclockwise to adjust the volume that fits your ears. Know the Radio Battery Installation Note: If you need to remove the battery, please turn off the radio first, then lift up the bottom battery latch and take out the battery pack.
Antenna Installation Note: Do not hold the radio by its antenna; otherwise, the performance and service life of radio may be affected. Belt Clip Installation screws from the device. Step 2: Align the radio screw holes on the belt clip, and then tighten the screws. Accessory Installation Step 1: Open the accessory connector cover. Step 2: Align the plug of the accessory (matching headset or programming cable) with the accessory connector.
Charging Function The charger tray can support to charge either radio or battery pack. Know the Radio Device charging Battery pack charging Charge Indicator LED lndicator LED no light LED glows red LED glows green Charge Status No load Charging Fully Charged Charging precautions: ·Please use the original charger tray of the model for charging. · When charging, it is recommended that the radio remain powered off during charging.
· The battery pack should be stored in a cool and dry place after being fully charged. Do not expose the battery pack near the fire or to the sun, otherwise there are safety risks. ·During charging, it is not recommended to transmit the radio. ·The battery pack may slightly heat up during charging, which is a normal phenomenon. Channel and Zone Selection Zone: A zone is a group of channels.
Transmitting/Receiving After starting up successfully, the user can conduct various call operations. Precautions for radio use: ·When the radio is transmitting, keep the radio in a vertical position, and keep the microphone 2.5-5 cm away from the mouth. When transmitting, the radio should be at least 2.5 cm away from the head or body. ·Do not turn on/off the radio repeatedly during use, and adjust the volume to a level suitable for your hearing. Precautions for radio operation: 功能 介绍 Features 1.
Program Button User can configure program button functions via programming software. Corresponding features as below: - Emergency Alarm - Zone Selection - One Touch Call - DM On/Off - High/Low Power Switch - Scan On/Off - VOX On/Off 1. Enter the basic setting interface of programming software to configure or modify the device name. 2. Device name can support: Letters, numbers, Chinese, special characters, etc. Device ID 1.
3. To cancel the password, clear the password and confirm. 4. To change the password, key in the old password first, and then enter the new password to rewrite. 5. When you forget the password, you can perform factory reset or reprogram it. Sub-Code Frequency Configuration 1. The sub-code frequency supports CTCSS, DCS positive code, DCS reverse code, standard sub-code and non-standard sub-code. 2. Only when the transmitting sub-code and receiving sub-code are the same can they communicate to each other. 3.
4. If set to low power, the transmission distance is short, but the low power consumption. DTMF Configuration 1. The DTMF interface of the programming software can configure the DTMF function related parameters, such as side tone, duration, interval time, online telegram code, offline telegram code, transmission start sound, transmission end sound, transmission start and end sound. 2.
lowercase letters. 3. The same encryption template must be configured for transmitter and receiver for normal intercom, otherwise the speech content cannot be heard clearly. 4. The main purpose is to prevent the content of the speech from being monitored by other people at the same frequency. Color Code The color code can identify a system. Users who need to communicate with each other must set the same color code. The radios does not respond to channel activities that do not match the preset color code.
respond, the recipient can talk back. 1. Configure “One touch call” through CPS and send “Call Alert”. 2. After “Call Alert” is sent successfully, it will prompt a beep sound ,otherwise error tone will sound. 3. When “Call Alert” is received, alert tone will continue to sound. Remote Monitor (Private call only) Radio Check (Private call only) Radio check is used to check whether it can communicate normally with the other party. 1. Configure “One touch call” through CPS to send “Radio Check”. 2.
Activate (Private call only) 1. The activation command is to remove kill status. 2. After sending activation command, it can change the other party from remote kill state to active state. After restarting, it can be used normally. Voice Control Function 功能 介绍 Features 1. Preset the [Program] key to [VOX On/Off] key through programming software. 2. Press the [VOX On/Off] key to turn on/off the voice control function.
Power saving function To extend battery life, the user can enable power saving mode. In the power saving mode, the user can press [PTT] key to transmit or the radio can receive normally when a signal is detected. The power saving function can be enabled/disabled by programming software. GPS Function (for specific models only) Vibration Function (for specific models only) You can set whether to enable the vibration function, which will be applicable to short message, private call prompt, call prompt, etc.
Disclaimer This manual strives for the accuracy and completeness of its content during the preparation. Repeated review has been carried out, and the company will not assume any responsibility for errors or omissions that may occur during the output and printing process. In addition, due to the continuous development of technology, the company reserves the right to change the product design and specification without prior notice.
Model Number: Telephone: Post Code: User’s Name: Chop b y Dealer 4.Warranty void if seal broken. 5.1 year guarantee for product, 6 months for charger,battery and antenna . 6.The user can get repairing service from the following ways: a.Go to the shop where you buy the machine b.Our local repairing agent REMARKS: 1.This guarantee card to be kept by the user ,no replenishment if lost. 2.This guarantee card to be filled & chopped by the dealer,or it is invalid. 3.
*Use an authorize audio accessories compatible to device. For more information about accessories, please consult your local dealer.