Analog Radio User's Manual Rev.
FCC Warning Using Tips Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless devices. Important FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the FCC RF exposure guidelines when used with accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use only the supplied antenna.
ISEDC Radiation Exposure Statement Using Tips For face up operation, this model device has been tested and meets the ISED RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that Contains no metal and that positions the handset a minimum of 25mm from the face.
Product Control Antenna Power key LED Indicator PTT key Accessory Port Down key Charging Port Menu key Programmable key Microphone Speaker Charging contacts 4 Know the Radio Up key
Radio LED Indicators Know the Radio Radio Status LED Indication Standby Blinking Green Low Battery Blinking Red Transmit (TX) Solid Red Receive (RX) Solid Green Programming Mode (Read from Radio) Fast Blinking Red Programming Mode (Write to Radio) Fast Blinking Red 5
Battery Installation 1. Use finger tip to pull the latch as shown in picture below to remove battery cover. 2. Put the battery pack into the battery compartment, close the battery cover with snap fit all latches. Ensure the battery cover is fully fix to radio. 3. Install the belt clip holder using a coin or screwdriver as shown in the picture. 6 熟悉本 机Radio Know the Note: To remove the battery pack, please turn off the radio first.
Belt Clip Installation 1. Align the guide groove of the belt clip to the belt clip holder on the battery cover and install it appropriately. Note: The belt clip can be installed from any direction, clip on the belt, and the radio can rotate 180 degrees. 2.Take out the belt clip to the following angle with belt clip bottom face up, and remove it toward the top. 熟悉本 机Radio Know the Figure 1 Figure 2 Accessory Installation Step 1: Open the accessory connector cover.
Charging Function 1. This device can support charging with charger tray or direct USB charging. During charing, radio LED indicator lit red. When complete charging, LED indicator will turn green. Charging precautions: ·Please use the designated charging base of the model for charging. ·When charging the device, it is recommended to turn off the radio first. ·To obtain the best battery performance, please charge for at least 5 hours for the first time.
·During charging, it is not recommended to transmit the radio. ·The battery pack may slightly heat up during charging, which is a normal phenomenon. Power On/Off Press and hold [Power] key to power on the radio. Repeat the step to power off the radio. Check Channel and Battery Level Status In standby mode, briefly press the power button to check channel and battery level status. 功能介 绍Radio Know the Volume Control Press [+] to increase the volume. Press [-] to decrease the volume.
·Do not turn on/off the radio repeatedly during use, and adjust the volume to a level suitable for your hearing. ·Before using the radio for communication, please set the transmitter and receiver to the same frequency point. ·For the analog channel that requires communication, please set the transmitter and receiver to the same sub-audio frequency. Menu Selection 1. The [Menu] key were set to (i) Switch channel, (ii) Set high/low power, and (iii) Turn on/off scanning. 2.
Setting High/Low Power (US Only) Press the [Menu] key thrice to enter high/low power setting, and press [+] or [-] key again to switch high/low power. If the radio is not operated for 3 seconds or [PTT] key is pressed, it will exit the menu mode. TOT (Time out Timer) Function 功能 介绍 Features In order to prevent some users from occupying the same channel for a long time, users can set to enable the TOT function.
Monitor (Default on Programmable Button) Monitor feature is pre-programmed on 'Program' button. Press and hold to enter monitor mode. Release the button to exit. Power Saving Function The power saving function can be enabled/disabled by programming software. Low Battery Alert Program Button User can configure program button functions via programming software.
Squelch Level(SQ) User can configure SQ setting via programming software. If SQ is set to 0,the radio will be in receiving mode. Setting New Read/Write Password To further enhance privacy and security, user can configure password. through programming software interface. 1. Set new read/write 8-digits password. 2. To change password, first input old password, press to confirm in order to unlock and input new password. 3. To remove password, leave it blank and press confirm.
14 Model Number: Telephone: Post Code: User’s Name: Chop b y Dealer 4.Warranty void if seal broken. 5.1 year guarantee for product, 6 months for charger,battery and antenna . 6.The user can get repairing service from the following ways: a.Go to the shop where you buy the machine b.Our local repairing agent REMARKS: 1.This guarantee card to be kept by the user ,no replenishment if lost. 2.This guarantee card to be filled & chopped by the dealer,or it is invalid. 3.
+